Amico M-FILL-OXY-S Manual

Operation & Maintenance Manual
Emergency Oxygen Inlet Station
Surface Mount High Pressure

Contents
Introduction 3
Medical Facility Responsibility 3
Installation of Emergency Oxygen Inlet Station 4
Ordering Information 4
Schematic Drawing 4
2 Amico Pipeline

Introduction
Medical Facility Responsibility
www.amico.com 3
As required by NFPA 99 (National Fire Protection Association) “Health Care Facilities”, oxygen systems having the source
of supply outside the building shall have an inlet to connect a temporary, auxiliary source of supply for emergency or
maintenance situations. This connection shall include necessary valves and to allow for an emergency supply of oxygen
and isolation of the normal source of supply. The inlet connection shall be a 1” female npt connection and be provided
with a plug to prevent entry of foreign matter into the oxygen system when not in use.
Amico Emergency Oxygen Inlet Station will perform in conformity with the descriptions contained in this manual and
accompanying labels and/or inserts, when assembled, operated, maintained and repaired in accordance with the
instructions provided.
Emergency Oxygen Inlet Stations must be inspected periodically. A defective product should not be used. Parts that
are broken, missing, plainly worn, distorted or contaminated, should be replaced immediately. Should such repairs or
replacements become necessary, please contact your local distributor.

4 Amico Pipeline
1. Anchor the oxygen inlet station on a nished wall with the appropriate necessary hardware.
2. Before brazing, wrap wet rags around the tube extension next to the valve to prevent overheating and
possible damage to the valve seals. Connect copper tubing to the copper extension using brazing methods
and materials in accordance with NFPA 99 or CSA Z7396.1. Once the valve extension is cool, remove rags.
3. Test the system for leaks (per appropriate standards).
Emergency High Pressure Oxygen Inlet Station Surface Mounted M-FILL-OXY-S
EMERGENCY OXYGEN FILL STATION ENCL. SURF. 00-M-X-OXFIL-BOX-S
EMERGENCY OXYGEN FILL STATION LABEL 00-M-X-MAN-18-SIMP
REGULATOR SR450ME-996 FOR SIMPLEX 00-M-X-MAN-18-SIMP
B-50 ADAPTOR CGA-540 - 1/4” NPT 00-M-X-MAN-20
1/4-20 HEX FINISHED NUTS 00-C-H-HEXNUT-02
962 CGA-540 NUT & PLUG 00-M-X-MAN-36
138R-1/2”CLAMP 00-M-X-MAN-48B
PLATED THREADED 3/8-16*1-3/4”TAP BOLT 00-M-X-MAN-49
NIBCO BALL VALVE THREADED 1” 00-V-X-VLV-NIB-10T
VALVE HANDLE SLEEVE FOR 3/4”TO 1-1/4” 00-V-C-VLV-HAND-M
3/8”- 16 HEX NUT 00-H-NHF-37NC
ELBOW 90 DEG, 1/4”* 1/4”FEM (HP) 00-M-X-OXF-HP-ELB
110-HB REDUCING BUSHING 1/4”F * 1”M 00-M-X-OXF-HP-MFSELB
ELBOW MALE 1”NPT * 1”SOLDER 00-M-X-OXF-MFSELB
EMERGENCY OXYGEN FILL STN. BRACKET 00-M-X-OXFIL-BRKT
FOAM SPONGE FOR MANIFOLD DOOR 00-M2-X-FOAM-02
1/4-20 x 3/4”PAN PHIL.MACH.SCRW.PLTD 00-H-RPH-0220-10
8-32 PLATED HEX NUT 00-H-NHM-08NC
1/4-20 * 1/2”HEX CAP SCREW GRADE-2 00-C-H-CST-0220-05
POWDER COAT PAINTING - OXY FILL STATION SURF. 00-M-X-OXFIL-PNT-S
OXY FILL PIPE WITH ELBOW SOLDERED 1” 00-M-X-OXFIL-END-E
1/4”-20 x 3/4” PAN HD. PHIL. PLATED STEEL 00-H-MPP-025UNC-075PLTD
#2 x 1/4” PAN PH. PLATED SELF TAP SCREW 00-H-MPP-0204-TAP
Optional Check and Relief Valves (to be ordered separately):
Check Valve 1” VV-CHK-10
Check Valve 1-1/2” VV-CHK-15
Check Valve 2” VV-CHK-20
Relief Valve M-X-MAN-72W-075
Relief Valve Pipe Away Adapter 1/2”NPT M-X-PIPEAWAY-05
Installation of Emergency Oxygen Inlet Station
Ordering Information

www.amico.com 5
Shuto
Valve
16
[406]
Schematic Drawing
Inlet
Oxygen
connection
2” NPT
2”Type “K”
Copper Outlet Pipes
9
[228.6]
6
[152]
12
[305]
Main Line
Shuto Valve
Pressure
Switch
Relief Valve
75 PSIG
Turn Down
and Screen
Emergency Low
Pressure Oxygen
Inlet Box
Main Oxygen
Supply Check Valve
(2 required)
Check Valve
(2 required)
11
[280]

Amico Pipeline | www.amico.com
85 Fulton Way, Richmond Hill
Ontario, L4B 2N4, Canada
Toll Free Tel: [phone]
Toll Free Fax: [phone]
Tel: [phone]
Fax: [phone]
APE-OPER-MAINT-EOISHPSURFMNT-V1.0 PRINTEDAUG11
www.amico.com