Amigo APH50C User manual

APH50C
Internal antenna
IndoorAccess Point:APH50C/APH51C
QuickInstallationGuide

APH51C
External antenna
STEP1. PackageContent
(1)Access Point: APH50C/APH51C/
(2)PowerAdapter
(3)Wall Mounting screw set
(4)Ceiling mounting bracket
(9/16” and 15/16” flat T-bar included)
(5)Dipole 2.4Gantennasx2, Dipole5Gantennasx2(APH51C/)

STEP2. Mounting Kits Installation
ForWall Mount Installation
ForCeiling mount Installation

STEP3. Connectingthe DeviceforConfiguration
(1)Connectone endof the Ethernet cable into the LAN1 port of the Access
Point and the otherend to the Ethernet port onthe computer.
(2)Plug in powersource by different ways that depends on user setup
environment
(A) PoESwitch(Plug in fromLAN1 Port)
(B) PoEInjector(Plug in fromLAN1 Port)
(C) DCPowerAdapter(Plug in fromDC Jack)
- Connectthe PowerAdapterto the DC-IN port of the Access Point
and plug the otherend into an electricaloutlet.
Note:The Access Pointsupports both IEEE802.3atPoE(Powerover Ethernet)orthe
included poweradapter.You may use either oneas the powersource.DONOTuseboth at
the sametime.
STEP4. IPAddressConfiguration
(1) Once your computer is on, ensure that your TCP/IPis enabled.Open
NetworkConnectionsandthen click Local Area Connection.Select
Internet ProtocolVersion4 (TCP/IPv4).
(2)If your computer is alreadyon a network,ensurethat youhave set it to a
StaticIPAddress on the interface. (Example: 192.168.1.2,the Subnet
Maskaddress as 255.255.255.0.andDefaultGatewayis 192.168.1.254)

STEP5. AccessPointSetup
(1)Open a web browseron your computer. In the address bar of the web
browser,enter192.168.1.1andenter.
(2)Aloginscreenwill appear.The device do not have usernameand the
passwordsettingsand canclickloginto access.
(3)The accesspointuser interface will appear.This device canoperate in
AccessPointoperating mode. Usercanstartto complete the device setup.

Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.

Professional installation instruction
1. Installation personal
This product is designed for specific application and needs to be installed by a qualified
personal who has RF and related rule knowledge. The general user shall not attempt to install
or change the setting.
2. Installation location
The product shall be installed at a location where the radiating antenna can be kept 20cm
from nearby person in normal operation condition to meet regulatory RF exposure
requirement.
3. External antenna
Use only the antennas which have been approved by the applicant. The non-approved
antenna(s) may produce unwanted spurious or excessive RF transmitting power which may
lead to the violation of FCC limit and is prohibited.
4. Installation procedure
Please refer to user’s manual for the detail.
5. Warning
Please carefully select the installation position and make sure that the final output power
does not exceed the limit set force in relevant rules. The violation of the rule could lead to
serious federal penalty.