Ampac ZoneSense Plus Guide

Fire detection and evacuation solutions that save lives.
ZoneSense PLUS
Installation & Commissioning
MAN1563-5

MAN1563-5
2
Contents
1 About This Manual.............................................................................................................................. 4
1.1 Introduction ................................................................................................................................. 4
1.2 General Requirements.................................................................................................................. 4
1.3 References ................................................................................................................................... 4
1.4 Symbols........................................................................................................................................ 4
2 System Overview................................................................................................................................. 5
3 ZoneSense PLUS Description ............................................................................................................... 6
4 Placing the Basic System into Operation ............................................................................................. 7
4.1 Unpacking .................................................................................................................................... 7
4.2 Anti-Static Precautions ................................................................................................................. 7
4.3 Working On The System ............................................................................................................... 7
4.4 The Cabinet.................................................................................................................................. 7
4.5 Mounting The Cabinet.................................................................................................................. 8
5 PCB Removal / Replacement............................................................................................................... 9
5.1 Power Supplies and AC Mains Installation....................................................................................10
5.1.1 Primary Power Supply..........................................................................................................10
5.1.2 Mains wiring........................................................................................................................10
5.1.3 Connecting the Panel...........................................................................................................10
5.1.4 Connecting the Mains Earth.................................................................................................10
5.1.5 Connecting the Mains Power to the Power Supply...............................................................11
5.2 Battery Charger...........................................................................................................................12
5.2.1 Connecting the Stand-By Batteries.......................................................................................12
6 Main Control Board............................................................................................................................13
6.1 Connector numbering..................................................................................................................14
6.2 Terminal Block Numbering ..........................................................................................................15
6.3 Earth Monitoring.........................................................................................................................17
6.4 Communications (TB2) ................................................................................................................17
6.4.1 Main Card Comms Link (K1) .................................................................................................17
6.5 Inputs –Monitored (TB3).............................................................................................................18
6.5.1 Common Terminal (TB3 Com) ..............................................................................................18
6.5.2 Door Switch Input (TB3 Com / 1)..........................................................................................18
6.5.3 MCP (TB3 Com / 2)...............................................................................................................18
6.5.4 Fault Input (TB3 Com / 3).....................................................................................................18
6.6 Detector Zones (TB13 & TB14).....................................................................................................19
6.6.1 Detector Configuration ........................................................................................................19
6.7 Outputs - Monitored (TB4) ..........................................................................................................21
6.7.1 Alarm Outputs .....................................................................................................................21
6.7.2 External Bell Output (TB4 1 / 2)............................................................................................21
6.7.3 Warning System Output (TB4 3 / 4)......................................................................................22
6.7.4 Ancillary Control Facility (ACF Output) (TB4 5 / 6) ................................................................22
6.7.5 Alarm Signalling Equipment (ASE Output) (TB4 7 / 8) ...........................................................22
6.7.6 Conventional Sounder Circuit Wiring (TB4) ..........................................................................23
6.7.7 Sounder Loading and Distribution........................................................................................23
6.8 Outputs –Monitored Open Collector (TB5)..................................................................................24
6.8.1 Alarm Output (TB5 1 / 2)......................................................................................................24

MAN1563-5
3
6.8.2 Fault Output (TB5 3 / 4) .......................................................................................................24
6.9 Outputs –Volt Free Relay Programmable ....................................................................................24
6.9.1 Alarm Output (TB5 5 / 6 / 7).................................................................................................24
6.10 Outputs –Volt Free Relay Non-Programmable.............................................................................24
6.10.1 Fault Output (TB5 8 / 9 / 10) ................................................................................................24
6.11 Auxiliary Power Output (TB12 1 / 2).............................................................................................24
6.11.1 Reset Terminal / Buzzer Output. (TB12 / 3) ..........................................................................25
6.11.2 Buzzer..................................................................................................................................25
7 Expanding the FACP with compatible Ancilliary Board.......................................................................26
7.1 Installation and Wiring of Add On Cards and Boards ....................................................................27
7.2 Internal Communications Connector (RS485)...............................................................................28
8 Battery Capacity Calculation...............................................................................................................29
8.1 Description..................................................................................................................................29
8.2 Power Supply Rating....................................................................................................................29
8.3 Power Supply & Battery Calculator ..............................................................................................30
8.4 Primary Power Source Calculations..............................................................................................31
9 Battery Guidelines..............................................................................................................................33
10 Trouble Shooting Chart ......................................................................................................................34
11 Installation and Commissioning Report..............................................................................................35
11.1 Procedure....................................................................................................................................36
11.2 System Information.....................................................................................................................37
12 Statement of Installation Compliance ................................................................................................40
13 Installation Details .............................................................................................................................42
14 Certification Information....................................................................................................................43
15 Specifications .....................................................................................................................................44
16 Glossary of Terms...............................................................................................................................45
17 Definitions..........................................................................................................................................46
18 Quick Reference Guides .....................................................................................................................47
19 Front Panel Configuration Labelling ...................................................................................................50

MAN1563-5
4
1About This Manual
1.1 Introduction
This manual contains all the information required to install, commission and operate the ZoneSense PLUS Fire Alarm
Control Panel (FACP) and is only available to and for the use of personnel engaged in its installation, commissioning
and operation.
1.2 General Requirements
The ZoneSense PLUS FACP has been designed and manufactured from high quality commercial components so as to
comply with major world standards. To ensure these standards are not compromised in any way installation staff and
operators should;
➢Be qualified and trained for the task they undertake;
➢Be familiar with the contents of this manual prior to the installation, commissioning or operation of a
ZoneSense PLUS control system;
➢Observe anti-static pre-cautions at all times; and
➢Be aware that if a problem is encountered or there is any doubt with respect to the operational parameters
of the installation the supplier should be contacted.
1.3 References
ZoneSense PLUS Technical Manual
ZoneSense PLUS Operation and Programming
Australian Standards:
AS4428 - Fire Detection, Warning, Control and Intercom Systems –Control and Indicating Equipment. Part 1 and Part 5
1.4 Symbols
Important operational information
Note: Configuration considerations
Observe antistatic precautions
Mains supply earth
DANGER mains supply present

MAN1563-5
5
2System Overview
The ZoneSense PLUS 4 and 8 zone FACP complies with the highest level of approval for any applicable code and can be
connected to an appropriate Fire Service monitoring facility.
As a Minimum, the conventional panel meets the following Standards;
➢AS4428
➢AS4214
Only devices compatible with ZoneSense PLUS should be used in an installation. These are listed in this document.
Features
➢The front panel 8 x 2 line LCD, navigation keys and the Menu/Enter keys allow the ZoneSense
PLUS to be programmed “on site”. The same LCD and keys are also used for panel operation and
interrogation.
➢Four monitored conventional Alarm circuits.
➢Two optional auxiliary input connections.
➢Two open collector outputs (fire and fault).
➢Two relay outputs (ancillary and fault).
➢Optional external buzzer or reset output.
➢System expansion capabilities / options:
➢Password entry to a wide range of programming and diagnostic functions which include;
•Zone configurations;
•MCP Zone assignment;
•Default display; and
•Zone labels;
➢A wide range of secure user functions. This includes the ability to isolate / de-isolate a large number of
system functions.
➢Flush or surface mountable enclosure. A surround is required for the metal cabinet
➢Controls have tactile and audible feedback of operation.
➢All terminals cater for 2.5mm cables.

MAN1563-5
6
3ZoneSense PLUS Description
The ZoneSense PLUS Fire Alarm Control Panel (FACP) is approved to AS4428 and is available in ABS (BX1) or
metal cabinets (BX20) with either four (4) or eight (8) zone conventional detection circuits.
The 2 line LCD display allows the user to view system status, faults/isolates, prompts for system commands; and
guides the user during on-site programming.
➢Key features of the ZoneSense PLUS FACP include:
➢Multi-purpose expansion capabilities
➢Multi-level password access
➢Tactile-feedback controls
➢Selectable end-of-line
➢Keyed entry
Each zone can accommodate up to 40 conventional detectors that can be programmed to function in one of the
following modes:
➢Normal (latching)
➢Alarm Verification Facility (AVF)
➢Non-latching
➢Self Reset
➢Dual selectable Agent Release
The standard ZoneSense PLUS FACP comprises of a main printed circuit board and a power supply unit.
The main board provides:
➢The visual indication and control
➢Two Relays with volt-free Alarm and Fault changeover contacts
➢Termination for zones
➢Monitored outputs
➢Power supply monitoring
➢RS485 communications port
The ZoneSense PLUS can be quickly converted to an AS4214 approved Agent Release System with the use of the
Agent Release Module and if required a remote Local Control Station (LCS). Up to four LCS’s can be connected to
the FACP via a dedicated RS485 communications port.
CN4CN3
CN2
CN1
0V +27V
POWER
CN4CN3
CN2
CN1
0V +27V
POWER
BRD25MCB
CN6
CN10
CN8
CAB1905
CAB2117
CN9
CN5
CN1CN2 CN2 CN1
CAB1905
CAB1902
CAB1926
TO BATTERIES
CAB2290
TB3 INPUTS
COM
MCP
DS
FLT
10K EOL
NOTE CAB 2074:
GREEN + BLACK TO 'COM'
RED TO 'DS'
CAB2074
CAB2289
BLACK
RED
A
N
CAB1911
TO EARTH OUTPUT
OF 25PSU
EXTERNAL EARTH
TO EARTH INPUT
OF 25PSU
FRONT PANEL
ADD ON 1
BACK PANEL
ADD ON 1
TB4
KNOCKOUTS
BOTTOM MOUNTING HOLES
POWER
SUPPLY
KEYHOLES MOUNTING HOLES
FRONT PANEL
ADD ON 2
BACK PANEL
ADD ON 2
Figure 1: Typical Example of LoopSense Plus –AR

MAN1563-5
7
4Placing the Basic System into Operation
4.1 Unpacking
Carefully unpack the ZoneSense PLUS
The package should include:
➢Main Card, with all controls and indicators mounted directly onto it;
➢a switch-mode power supply;
➢2 X 12 Volt batteries connected in series.
➢2 X 003 keys
4.2 Anti-Static Precautions
To prevent damage to components, modules and boards, anti-static precautions MUST be observed while performing
any task within the FACP. The same applies to those situated in the field
4.3 Working On The System
Prior to unplugging any connector, connecting or disconnecting any wiring, removing or replacing any module or
board, ensure that both the Mains and Batteries have been isolated to prevent damage to panel components.
4.4 The Cabinet
Features:
➢The cabinet is available in three different styles. Each style has the capability of being either surface or flush
mounted. With flush mounting though a surround is required.
➢Normally painted Arch White Ripple. Other colours are available on request.
➢The inner and outer door hinges are mounted on the left-hand side of the cabinet which allow the doors
open to an angle of 100º. Locking is normally keyless though keyed entry is available on request.
➢Knockouts are positioned at the top and rear of the cabinet to simplify cable entry.

MAN1563-5
8
4.5 Mounting The Cabinet
Note: It is recommended the cabinet should be installed in a clean, dry, vibration-free area.
Open the front door. Use the keyhole mounting holes in the top corners and in the lower middle of the unit to mount
it on the wall. Cables to connect the system to its external actuating devices are brought in through the knockouts on
the top or bottom of the cabinet.
R 6mm.
12 mm
Tap lightly around the
rim of the knockout
3 mm
Figure 2: Example ZoneSense PLUS Mounting & Removing Knockouts
POWER
SUPPLY
BRIDGE
ASSEMBLY
TO REMOVE FRONT DOOR
SLIDE THE DOOR UPAND
AWAY FROM THE
HINGES
NOTE: BATTERY TRAY SITS HERE IN THE BOTTOM OF THE CABINET
REMOVING
KNOCKOUTS
ABS KEY SLOTS
Figure 3: Exploded and Assembled View of the Basic ABS Model FACP with 003 Key Entry
AMPAC
DOOR RELEASE PINS
DOOR RELEASE PINS
FRONT PANEL
ADD ON CARD
SURROUND
RELEASE CLIP
FRONT PANELADD ON
CARD SURROUND
RELEASE CLIP BEHIND
Figure 4: ABS Door Key and Front Panel Add On Card Surround Release Clip

MAN1563-5
9
5PCB Removal / Replacement
If the PCB’s have to be removed the following precautions should be observed;
➢Removing the door will provide better access to the boards and ensure the hinges are not accidentally
stressed.
➢Personal anti- static procedures must be followed.
➢When disconnecting the 20 way connecting cable from the PCB, make sure that the cable remains connected
to at least one board to prevent it being misplaced.
Note: Care should be taken when detaching this connector as it is necessary to depress the small locking tab to
unlock the connector from its base. To reconnect the cable the connector must first be correctly aligned then pushed
into the socket so it locks into position.
➢Carefully remove the retaining screws at each corner of the board taking care not to damage any of the
components.
➢Place each board into anti- static storage once removed.
Push Tab Inwards
and Gently Pull
the Connector
From the Socket
Connector

MAN1563-5
10
5.1 Power Supplies and AC Mains Installation
5.1.1 Primary Power Supply
The ZoneSense PLUS Supply PCB combines the functions of;
➢A mains to D.C. switched mode power supply unit that operates from a supply of; 204 - 264VAC @ 47 –63Hz
supplying the system while all zones are in alarm
➢A battery charging and monitoring unit
➢A mains fail is detected when the PSU voltage drops below 24V.
5.1.2 Mains wiring
The requirement for the Mains supply to the FACP is fixed wiring, using three core cable (no less than 0.75mmand no
more than 2.5mm) or a suitable three conductor system, fed from an isolating switch fuse spur, fused at 3A. This
should be secured from unauthorised operation and be marked 'FIRE ALARM: DO NOT SWITCH OFF. The Mains supply
must be exclusive to the FACP.
5.1.3 Connecting the Panel
Connecting ZoneSense PLUS internal connections and boards is best undertaken immediately prior to Commissioning.
Before beginning ensure all devices on the circuits are correctly connected and that cable integrity is verified
throughout the installation.
Important: DO NOT use an insulation tester ('Megger') with any electronic devices connected. Faults occurring in
the wiring which are not picked up at this stage will almost certainly result in spurious and intermittent faults when the
equipment is energised.
Important: Under no circumstances should the ZoneSense PLUS panel be operated without the Power Supply
correctly mounted in the enclosure and the retaining screws securely tightened.
5.1.4 Connecting the Mains Earth
All earth cabling shall be terminated to the panel Chassis Earth Terminal in a star configuration.
The earth cable closest to the cabinet body shall have an M4 SPW beneath the lug then an M4 SPW and M4 nut.
Each additional earth cable shall be terminated with an M4 SPW and M4 nut.
An additional M4 nut and M4 SPW are fitted to the Chassis Earth Terminal for installers to connect their Mains Earth.
M4 Shake Proof Washer
M4 Shake Proof Washer
CHASSIS EARTH TERMINAL
M4 Nut
Earth Cable
Earth Cable
M4 Nut
M4 Shake Proof Washer *
M4 Nut *
Note:
* Extra M4 Nut and M4 SPW are
provided finger tight on the Earth bolt.
Figure 5: Panel Earthing

MAN1563-5
11
5.1.5 Connecting the Mains Power to the Power Supply
CHASSISEARTH
TERMINAL
+BATT-
CAUTION:
FORCONTINUEDPROTECTION
AGAINST RISK OF FIRE REPLACE
ONLYWITH SAME TYPE 2AFUSE
O
F
F
O
N
METAL
COVER
DCOUTPUT
ETH+27V 0V
1
12
6
8
4
3
5
7
(ACIN)
CN5TOTHERMISTOR
EXTENSIONSOF PIN 1
(TEMPSENSE RTN)AND PIN6
(TEMPSENSE) OF RJ45
CN2: RJ45 PINOUTCONNECTIONS
1.TEMP SENSE RTN
2.SUPPLYSENSE
3.PSUVADJ
4.CHARGERON
5.LOAD ON
6.TEMPSENSE
7.BATTERYVSENSE
8.OV
CABLEDTOTHE
MAIN BOARD
Battery 2
12Volts
Battery 1
12 Volts
+
--+
2
PROTECTIVE PERSPEX
COVER
HIGH VOLTAGEPRESENT
INDICATOR UNDERCAGE
COMBINEDMAINS SWITCH
& MAINSINDICATION
NEUTRAL(BLUE)
EARTH (GREEN)
ACTIVE (BROWN)
NOTE: MAINS CABLE
SHOULD BE NO LESS
THAN 0.75mm
1 2 3
CN5
CN2
TB2
TB1
SW1
F1: 2A
Fuse
27VTOTHE MAINCARD
(3 WAYPANDUIT)
A
LED
AC ON
DC ON
LED
DANGER
N
MAINS CABLE
Figure 6: Power Supply Battery Charger Wiring (3A PSU SHOWN)

MAN1563-5
12
5.2 Battery Charger
The battery charger is an integral part of the Power Supply and is capable of
➢Recharging standard sized system batteries within 24 hours
➢Detecting a missing, damaged or undercharged battery
➢Protecting the battery against reverse or a short circuit condition
➢Charging batteries in line with Sealed Lead Acid battery manufacturers circuit temperature compensation
guidelines
The following table contains the thresholds for the corresponding battery faults:
Battery Voltage
Battery Fault Condition
VBATT < 23.5V
BATTERY LOW
*VBATT < 22V
BATTERY DAMAGED
VBATT < 20V
BATTERY MISSING
Note: Battery disconnect has been incorporated to prevent the battery from discharging through the battery
charger should the charging voltage be less than the battery voltage.
5.2.1 Connecting the Stand-By Batteries
The capacity of the batteries to be installed depends on the panel configuration and required stand-by time. To
calculate the required AH capacity of the batteries, refer to the calculation guide located in the rear of this manual.
Two new, good quality and fully charged 12V Sealed Lead Acid batteries are required as the emergency stand-by
power supply for the Panel. They are to be mounted in the bottom of the cabinet. In the ABS version a protective tray
is supplied in the packaging.
The batteries should be connected in series using the series link wire provided and located within the panel enclosure.
The red and black battery leads from the Power Supply (see Figures 4 & 5) should be run to the batteries in such a way
that there is no risk of them being damaged, and then connect the red wire to the positive terminal and the black wire
to the negative terminal.
The panel's sophisticated battery monitoring protects the batteries against deep discharge by activating a cut off
circuit when the stand-by supply voltage reaches approx 21 volts. If batteries are not fitted, are discharged or in poor
condition, the “FAULT" LED will be illuminated.

MAN1563-5
13
6Main Control Board
The Main Control Card and its front display panel combined with the Power Supply / Battery Charger and batteries
form the basis for the ZoneSense PLUS FACP.
DECAL
BRIDGE
PCB
SHIELD
ASSEMBLED
BRIDGE
Figure 7: Exploded view of the Control Panel
///
NO NC
C
///
NO NC
C
FUSE:5A.
OUTPUTS
NO C NC
MON.
COMMS
DC
OUT
INPUTS
ZONES
OUTPUTS
K1
U12
U7
TB14
TB13
SW12
SW11
SW10
SW9
SW8
SW7
SW6
SW5
SW4
SW3
SW2
SW1
R22
CN2
D2 D3
D4 D5
D6 D7
D8 D9
D10
D11
D12
D13
D14
D16
D17
D18 D19
D20 D21
D22 D23
D24 D25
D26 D27
D28
D29
D31
D38
TB2 TB3
CN7
TB4 TB12
TB5
BZ1 FS1
RL2 RL3
U2
U3
U6
U18
U20
U19
U1
X1
EXT
RS485
COMMS INPUTS
DISABLE
EARTH
ZONES
1 2 3 4
+ A -
+2-
+1-
+2+4-
+3-
+Z4-
+Z2-
3
OUTPUTS
C 1 +Z7-
-+Z8-+Z6-
+Z1- +Z5-
+Z3- + F -
MON.
TOP OVERLAY
ZONES
5 6 7 8
MON O/Ps 1 - 4
Ext Warn
Bell Sys ACF ASE ALM FLT
NO C NC
FLTALM
+ -
RST
or BZ
MON
O/Ps
COM DS MCP FLT
LCD
Power
Power Fault
System Fault
Earth Fault
External Bell Fault
Warning System Fault
ACF / Isolate
ASE Fault
External
Bell
Isolate
Warning
System
Isolate
Alarm
Acknowledge
Fault
Reset
Isolated
Isolate / De-isolate
Fault / Isolate
Alarm
ZONE 1 ZONE 2
ZONE 3 ZONE 4
ZONE 5 ZONE 6
ZONE 7 ZONE 8
ACF
Isolate Cancel
Menu
Enter
RELAY
OUTPUTS
Figure 8: Main Control Card Front PCB View

MAN1563-5
14
CN5: Comms & 27VDC ( 400mA Current
Limit ) To Backpan Boards. If the FACP
Backpan Configuration Exceeds 400mA
the 27VDC MUST BE TAKEN FROM CN10
CN9: Comms & 27VDC To Any
Cards Fitted To The Front Panel
( 400mA Current Limit )
Keyswitch
Link
CN1
CN8 CN10
TP61
TP60 TP59 TP58
TP40
TP39
TP37 TP36 TP35 TP34 TP33 TP32 TP31 TP30 TP29 TP28
TP27 TP26 TP25TP24 TP23 TP22 TP21 TP20 TP19 TP18 TP17 TP1
TP2
TP3TP4
TP5
TP6
TP7
TP8
TP9
TP10
TP11
TP12
TP13
TP14
TP15
TP16
MON.
+ - +Z3-
+Z5- +Z1-
+Z6-
+Z8- -
+Z7- 1 C
OUTPUTS
3
+Z2-
+Z4-
+3-
+4- 2+ +1-
+2-
+ -
REV._1
ZONES
+- +- - + - +
EARTH
DISABLE
INPUTS
COMMS
BOTTOM OVERLAY
CN1: The Link is inserted when the
Front Panel Keyswitch is not used
CN8: 27VDC In From the Power Supply
CN10: 27VDC ( P/S Current Limit ) to the Backpan Boards
CN6: Monitoring Comms from the Power Supply
TP 1 to 44
( See the Terminal Block
Quick Reference for Detail )
Cutout
Figure 9: Main Control Card Rear PCB View
Note: When connecting to the Brigade PSU Monitor board transient and “Flyback” (Back EMF) protection
methodologies MUST be applied.
6.1 Connector numbering
Connector
Purpose /Pins
CN1
Link pins & •when the front panel keyswitch is NOT used.
CN2
LCD Driver
CN3 & 4
LCD Back Lighting
CN5
Comms and +/- 27V and earth to the backpan boards. (Imax = 400mA)
Pins
& 0V
•& +27V,
& RS 485 Bus,
Tx. Enable
CN6
Monitoring / Comms from the Power Supply.
Pins
& 0V
•PSU Sense
PSU Adjust
Charger ON
Batt Load
Temp sense
Batt V Sense.
CN7
Factory Use Only
CN8
+/- 27V and earth from the Power Supply / Charger.
Pins
0V
•+27V
Earth
CN9
Comms to the internal front panel cards. (Imax = 400mA)
Pins
Pin connections are the same as CN5
CN10
+27V and •0V to the Sounder, Agent Release and Fan Termination back plan boards (Imax =
P/S limit). All other backpan boards, 27VDC supply is via the RJ45 Comms cable.

MAN1563-5
15
6.2 Terminal Block Numbering
Terminal Block
TP Number
AS4428
COMMUNICATIONS EXTERNAL
TB2/1
RS485 +
2
28
RS485 -
3
29
Shield
INPUTS
TB3/1
Common
2
25
Door Switch (monitored)
3
26
Manual Call Point (monitored)
4
27
Fault Input (monitored)
ZONES ( 25mA / Zone )
TB13/1
1
+ Zone 1
2
2
- Zone 1
3
3
+ Zone 2
4
4
- Zone 2
5
5
+ Zone 3
6
6
- Zone 3
7
7
+ Zone 4
8
8
- Zone 4
TB14/1
9
+ Zone 5
2
10
- Zone 5
3
11
+ Zone 6
4
12
- Zone 6
5
13
+ Zone 7
6
14
- Zone 7
7
15
+ Zone 8
8
16
- Zone 8
MONITORED OUTPUTS ( 500mA / O/p )
TB4/1
17
External Bell +
2
18
External Bell -
3
19
Warning System +
4
20
Warning System -
5
21
ACF + Aux Control Function
6
22
ACF -
7
23
ASE + Alarm Signaling Equipment
8
24
ASE -
OPEN COLLECTOR OUTPUTS ( 30 mA /O/P )
TB5/1
25
Alarm +
2
26
Alarm -
3
27
Fault +
4
28
Fault -
OUTPUTS VOLT FREE RELAY ( 1A @ 30V )
5
29
NO Alarm
6
30
C Alarm
7
31
NC Alarm
8
32
NO Fault
9
33
C Fault
10
34
NC Fault
AUX, RESET / BUZZER
TB12/1
35
Aux 24VDC + (Mon 500mA)
2
36
Aux 24VDC –
3
37
Reset/Buzzer 100mA max

MAN1563-5
16
+ -
RS485 MONITORED
INPUTS
COM DS MCP FLT
+ Z1 - + Z2 - + Z3 - + Z4 - + Z5 - + Z6 - + Z7 - + Z8 -
DETECTOR ZONES
+1 - +2 - +3 - +4 - + -
ALARM
+ -
FAULT N/O C N/C
ALARM
FAULT
N/O C N/C
AUX 24VDC
+ -
RST
BZ
EARTH
DISABLE
LAM 8 Way Remote Relay Board
EOL 3K3
Maximum of 40 Devices per Zone
ALL Un-used Zones MUST be Individually
Terminated with an EOL
ALARM OUTPUTS
Comms
Link
3 Sec Reset Pulse
Note: Comms Link is required when only one Systems Comms board is used
EOL
Resistor
EOL
Resistor
EOL
Resistors
EOL Termination Values Zone = 10uf, 3K3, 4K7, 6K8, 10K Monitored O/P's = 10Kohms
CN8:27V In from CN4 of the P/S
CN10: 27V Out to Backpan Termination Boards
CN6 PSU Control from CN2 of the P/S
Current Limited to 25mA. and
Detector Removal Facility Available Maximum 500mA / 24V Monitored Open
Collector
30 mA O/P's
Voltage Free
Contacts 1A/30V 500mA O/P
+24v / 100mA
0v
12v Batt 12v Batt
+
--
+
-BATT+
DC OUTPUT
OV +27V GND
12
12
6
8
4
3 5 7
TO THERMISTOR EXTENSIONS OF PIN 1 (TEMPSENSE RTN) AND PIN 6 (TEMPSENSE) OF RJ45
RJ 45 PINOUT CONNECTIONS 1.TEMP SENSE RTN 2.SUPPLY SENSE 3.PSU V ADJ 4.CHARGER ON 5.LOAD ON 6.TEMPSENSE 7.BATTERY V SENSE 8.OV
1 2 3
CN2
CN5
CN5
CN2
LED
CN4
CN3
Power Supply Unit ( PSU )
Rear of Main Card
Front of Main Card Illustrated External Cabling
Power Supply / Main Board Internal Wiring
Programmable Un-programmable
RST / BZ O/P is Programmable
as a Reset or Buzzer but not both
Fault Input
Door Switch
Fire MCP
ACF
Warn Sys
Bell
TB2 TB3 TB13 TB4 TB5 TB12
EOL
Resistor
Shield
Note: Bases are fitted with diodes if the detector removal facilty is used
EOL
Resistor
ASE
Terminate all 3 Optional
I/P's with EOL Resistor
TB14
Note: If a diode is NOT fitted
internally to the Bell / Sounder a
diode MUST be fitted as
shown - fit 1N4004 or similar
Bell
EOL
10K
Ohms
Warn Sys
EOL
10K
Ohms
Figure 10: General Wiring Diagram ZoneSense PLUS

MAN1563-5
17
6.3 Earth Monitoring
The earth monitoring disable/enable feature is accessible via the SYSTEM menu at access level 3. Disabling the earth
monitoring does not illuminate the Earth Fault LED on the control panel.
Note: If ZoneSense PLUS is connected to a third party system which has earth monitoring and it’s earth
monitoring is being affected by ZoneSense PLUS even after being disabled through programming the resistor R22 on
the Main Card in ZoneSense PLUS can be removed.
6.4 Communications (TB2)
External Communications Terminals (RS485) TB2 1, 2 & 3
The RS 485 output drives the remote cards and mimics up to a distance of 1.2km from the FACP. The external cabling
(1 pair twisted shielded cable plus power) is wired to TB2 +, - and earth.
Note: If a fault occurs on the communications line the common FAULT and SYSTEM FAULT LED’S will be
illuminated. Selecting the Faults Menu will display the fault details on the LCD.
6.4.1 Main Card Comms Link (K1)
K1 MUST be inserted when;
➢Front door panel cards and the Main Card are used as an FACP; or
➢Backpan boards and the Main Card are used as an FACP; or
➢Remote boards and the Main Card are used as an FACP.
K1
Comms
+ -
Comms Link
TB2
Earth Disable
Top Left Hand
Corner of the
Main Card
To LAMs and/or
Remote Relay Boards
TB3
D/SW MCP FLT
Manual Call Point
Door Switch Fault
Inputs
RS485 Com 1 2 3
Note: Terminate the 3 I/P's in 10K EOL
Figure 11: Comms Wiring Details

MAN1563-5
18
6.5 Inputs –Monitored (TB3)
6.5.1 Common Terminal (TB3 Com)
The COM terminal is used as the common for the following three 0v potential inputs.
6.5.2 Door Switch Input (TB3 Com / 1)
This optional input is used for connecting the FACP’s door switch. Connection is to TB3 COM & 1
6.5.3 MCP (TB3 Com / 2)
The optional external MCP I/P is monitored for normal operation and must be mapped to a particular zone.
To test the input insert the test key provided into the MCP. Removal of the key resets the MCP.
10K ohms
Termination
Resistor
12
3
Wiring to an MCP
K1
Comms
+ -
Comms Link
TB2
Earth Disable
Front Door
TB3
D/SW MCP FLT
Manual Call Point
Door Switch Fault
Inputs
RS485 Com 1 2 3
Note: Terminate the 3 I/P's in 10K EOL
Top Left Hand
Corner of the
Main Card
Figure 12: Typical MCP Wiring
6.5.4 Fault Input (TB3 Com / 3)
This optional input is used to bring a fault into the system from an external source. Requirements for the input are an
open collector or 0 volt, voltage free contact to initiate a fault. Connection is to TB3 COM & 3

MAN1563-5
19
6.6 Detector Zones (TB13 & TB14)
Zone circuit connections are made directly to TB13 & TB14 on the Main Card and if screened cabling is used the screen
is terminated at the panel's chassis earth terminal. All zones can be programmed to operate in one of the 5 different
configuration modes each with a reset time in the order of > 1 second < 2 seconds.
D/SW MCP FLT
Com 1 2 3 5 6 7 8
TB3 TB13 TB14
+ Z2 - + Z3 - + Z4 -
Detector Zones
L1 In
+
L2
-R
APOLLO SERIES 60 STANDARD BASE WIRING
EOL
Earth
L1 Out
L1 In
+
L1 In
+
L1 Out L1 Out
-
L2
-
L2
-
-R
Earth
-R
Earth
+ Z1 -
1 2 3 4
Selectable EOL Values:
10uF Capacitor
3K3 (Factory default)
4K7
6K8
10K
EOL EOL EOL
Figure 13: Typical Detector Wiring
6.6.1 Detector Configuration
The operating configuration modes are:
Operating Configuration
LCD
Normal
Normal
Alarm Verification Facility
AVF
Non Latching
No Latch
Self Reset
Self Reset
Agent Trigger Zone 1, 2, 3, & 4
T1, 2, 3, & 4
Note: AS1670 SECTION 8.6 ALARM VERIFICATION FACILITY states that alarm zone facilities used for the following
shall not be subject to alarm verification:
➢Manual call points.
➢Detectors used to activate fire suppression systems.
➢Detectors installed in hazardous areas.
➢Fire suppression systems.
➢Beam detectors where a beam-interrupt fault overrides the alarm state.
➢AZF’s containing fixed temperature detectors only.
➢Detectors that have integral alarm confirmation delays such as some multipoint aspirated smoke detector
systems.

MAN1563-5
20
Since the provision of alarm verification delays transmission of a signal to the monitoring service, it is desirable that it
only be provided where other efforts to eliminate unwanted alarm signals have been unsuccessful.
Note: EOL type (capacitive / resistive) and value are set in the Programming Menu
Note: A maximum of 40 ZoneSense PLUS compatible Optical / Heat and Ionisation Detectors or Manual Call
Points can be fitted to each circuit and mixed in any order.
Note: An End of Line EOL (Factory set default = 3K3) device must be connected across the terminals of the last
device on each zone circuit to allow the circuit to be monitored. Zones that are not used must also have an EOL fitted to
the zone terminals on the Main Control Board.