Ampac Wagner Titanus PRO SENS User manual

MAN3057-3
Wagner Titanus PRO•SENS® Item Number: 7010-1010 & 7010-1110
Conventional Line Interface (CLI)
Installation guide
Please observe anti-static precautions at all times.
Installation:
To complete installation you will need at least:
•A PRO•SENS® Unit
One or two Detector Heads
Note: 2 Head setups trigger the common Zone
An Air Filter Unit per Detector Head
•A Balanced Pipe System
Refer to the PRO•SENS® Technical Manual
MAN3046, and the “TranspTimeTITANUS”
pipe transport time calculator.
•A 27V Power Feed
Wiring to a Conventional Detection Zone
Setup PRO•SENS® Detector Head(s) & Base Board:
1. Ensure power is not connected to the PRO•SENS®.
2. Set the Detector Head DIP switches as required (see
the PRO•SENS® Technical Manual Section 4.3.1.1)
General recommended Detector Head settings are:
Sensitivity: As required for the installation.
Alarm Delay: As required to suit the installation.
Air Flow Range: Medium.
Fault Delay: 30 Seconds.
Fault Latched: As Required.
LOGIC•SENS: Off for Transit Time testing.
Note: Before selecting suitable settings consult
applicable local standards, regulations and job
specifications requirements.
3. Install the of the Detector Head(s):
Figure 2: Detector Head Installation
3.1 With a flat blade screwdriver, carefully undo
the snap-in housing closures by
simultaneously pressing in the clips located on
the top or bottom of the unit. Carefully lift the
housing lid. Pull the cable from the display
board and remove the lid.
3.2 If fitting the 2nd detector carefully remove the
plastic self-adhesive cover(s) on the aspirator
chamber to allow air flow to the detector head.
If necessary use a screwdriver to assist. (The
1st position ventilator cover is already
removed).
NOTE: The right hand side location is for when
only one detector is fitted. The left is for a
second detector.
3.3 Carefully break the corresponding knockouts
for the pipe system(s) required, again using a
screwdriver if required. (Marked as “I” and “II”
on the enclosure).
3.4 Note the correct detector head orientation
(figure 2) and install the detector by spreading
the support clamps and placing the detector
head between them. Both clamps should fit
tightly against the module and snap in audibly.
Press the support clamps together.
3.5 If two detector heads are being fitted, remove
the jumper JU4 from the base board (see Fig

MAN3057-3
Wagner Titanus PRO•SENS® Item Number: 7010-1010 & 7010-1110
Conventional Line Interface (CLI)
Installation guide
3) and move the jumper for pins 2+3 on JU3 to
pins 1+2 on JU3(see Fig 4)
3.6 Connect the detector module to the base
board via the supplied ribbon cable.
Connection: X1 for the 1st detector. X3 for the
2nd detector.
3.7 Set the ventilator voltage (See Fig 5) as
specified by the TranspTimeTITANUS
calculation. Remove the jumper for higher 9V
operation and leave in for 6.9V (default).
Figure 3: Jumper Setting: Two Detector Operation
Figure 4 Location of JU3
Figure 5: Ventilator Voltage Setting
Mount the PRO•SENS® Unit:
See Figure 6 for hole locations on the PRO•SENS®
box. Cylinder or flat head screws should be used with
a:
•Diameter of thread: max. 6 mm
•Diameter of head: 10 mm
Figure 6: Back Box Mounting Hole Positions
When selecting a position for the unit, make sure that
the air outlet of the PRO•SENS® and adjacent objects
is at least 10 cm. Please refer to Section 5.5 of the
PRO•SENS® Technical Manual.
The middle inlet in Fig 2 is for the first pipe (1st
detector) and the outer for the 2nd detector if fitted.
Note: Do not glue the Pipe connection to the
PRO•SENS® Unit. See Section 5.5.2 of the
PRO•SENS® Technical Manual.
Ensure there is room for the filter box (the filter box
contains a mounting template) and then connect
through to the air sampling pipe network.

MAN3057-3
Wagner Titanus PRO•SENS® Item Number: 7010-1010 & 7010-1110
Conventional Line Interface (CLI)
Installation guide
Wiring:
Bring the field cabling in through a suitable knockout
and terminate cabling to the CLI (See Fig 7). Power is
already pre-wired through to the PRO•SENS® Main
Board power supply terminals (See Fig 8).
Figure 7: CLI External Connections and Settings
Figure 8: PRO•SENS® Power Connection
Operation:
Check the installation over, and then apply power.
The Wagner Titanus Diagnostics Tool can be
connected to the APID Diagnostics Port “X2 Diag” on
the PRO•SENS® Main Board for display of detailed
system information.
Set 1 of the 4 DIP Switches “ON” for the required value
End Of Line (EOL) of the Conventional circuit from the
Main Panel (See Fig 7).
Go to Section 7 of the PRO•SENS® Technical Manual
for the Commissioning Procedure, ensuring that the
signals tested transmit through to the Main Fire Panel
system.
Once the unit is commissioned fit the front lid cover,
ensuring that the front lid ribbon cable does not clash
with the CLI buttons. Route the cable to the right hand
side of the CLI board.
Finally, check the button operations. The Disable button
toggles the disable condition for each Detector Head.
The LEDs are lit steady yellow when the corresponding
Detector Head is Disabled.
The Reset button resets the local PRO•SENS® alarm.
It does not reset latched alarms registered at the Main
Panel. This can be used for local testing. A reset at the
Main Panel performs a reset at the panel and the
PRO•SENS® device.
Flash Code Fault Reference:
The status of a detector head can be determined by a
flash code of the LED to the side of the DIP switches
on a detector head.
Detector Head Flash Code Reference:
Flashes:
Meaning:
Steady Lit
Hardware defect in the Detector Head
2 Flashes
Air Flow Too Small (Blockage)
3 Flashes
Air Flow Too Large (Fracture)
4 Flashes
Stabilising after Power On
Fault Diagnosis:
1. A CLI Reset or Isolate button is not operating.
Remove the front cover, check for free operation of buttons.
Route cables away from the switches before replacing cover.
2. The Smoke Level indication on the DIAG tool is
responding slowly.
Check if LogicSens is enabled. This can delay response.
Check the flow rate for low flow/pipe system air leaks.
3. A Detector Head is reporting low flow.
Check the detectors aspirator cover guard is cleanly removed.
Check for any blocks in the pipe system or aspiration holes.
4. A Detector Head is reporting high flow.
Check the detector module is seated properly.
Check for any breaks in the pipe system.
5. The CLI or PRO•SENS® is not responding.
Power down, check all cables are firmly connected, repower.
Measure the supply voltage.
For further information please refer to the PRO•SENS®
Technical Manual MAN3046 section 8 “Maintenance”
or contact your local Ampac branch for technical
assistance