Ampak AP6330 User manual

User Manual
MODEL No.:AP6330

2

1. Introduction
AMPAK Technology would like to announce a low-cost and low-power consumption module
which has all of the WiFi and FM functionalities. The highly integrated module makes
the possibilities of web browsing, VoIP , FM radio functional applications and other
applications. With seamless roaming capabilities and advanced security, also could
interact with different vendors’ 802.11a/b/g/n Access Points in the wirelessLAN.
The wireless module complies with IEEE 802.11 a/b/g/n standard and it can achieve up to a
speed of 72.2Mbps with single stream in 802.11n draft, 54Mbps as specified in
IEEE 802.11g, or 11Mbps for IEEE 802.11b to connect to the wireless LAN. The
integrated module provides SDIO interface for WiFi, UART / PCM interface for FM.
This compact module is a total solution for a combination of WiFi + FM technologies. The
module is specifically developed for Smart phones and Portable devices.
The module is limited to being installed in a fixed device and cannot be used in amobile
device. While the module is being installed to the platform, the pertaining rule with regardsto
15B must be evaluated. Further to the RF exposure, the device shall be installed tothe
mobile platform with 20cm, and not collated with othertransmitters

3

2. Features
802.11a/b/g/n dual-band radio — non-simultaneous dual-band operation
Concurrent FM (RX) RDS/RBDS, and WLAN operation
Simultaneous WLAN receive with single antenna
WLAN host interface options:
- SDIO v2.0 — up to 50 MHz clock rate
FM multiple audio routing options: PCM, eSCO,A2DP
IEEE Co-existence technologies are integrated die solution
ECI — enhanced coexistence support, ability to coordinate SCO transmissions
around WLAN receives
Asimplified block diagram of the module is depicted in the figure below.

4

3. Deliverables
3.1 Deliverables
The following products and software will be part of the product.
Module with packaging
Evaluation Kits
Software utility for integration, performance test.
Product Datasheet.
Agency certified pre-tested report with the adapter board.
3.2 Regulatory certifications
The product delivery is a pre-tested module, without the module level certification. For
module approval, the platform’santennas are required for the certification.
4. General Specification
4.1 General Specification
Model Name AP6330
ProductDescription Support WiFi/FMfunctionalities
Dimension L x W x H: 12 x 12 x 1.5 (typical)mm
WiFi Interface SDIOV2.0
Humidity Operating Humidity 10% to 95%Non-Condensing

5

5. WiFi RF Specification
Characteristics Description
IEEE 802.11 WLAN
Mode Supported
802.11b
802.11g
802.11n(20MHz channelbandwidth)
Data Rate 802.11b:1,2,5.5,11Mbps;
802.11g:6,9,12,18,24,36,48,54Mbps;
802.11n(HT20):MCS0-MCS7;
Modulation DSSS with DBPSK/DQPSK/CCK for802.11b;
OFDM with BPSK/QPSK/16QAM/64QAM for802.11g/n;
Operating Frequency
Range 2412-2462MHz for802.11b/g;
2412-2462MHz for802.11n(HT20);
Number of Channels 11 channels for802.11b/g;
11 channels for802.11n(HT20);
Transmit Power Max 21.12 dBm
Antenna Type Integral antenna via a SMAconnector
Characteristics Description
IEEE 802.11 WLAN
Mode Supported 802.11a(20MHz channelbandwidth)
802.11n(20MHz channelbandwidth)
Data Rate 802.11a:54/48/36/24/18/12/9/6 Mbps
802.11n:up to 600Mbps
Modulation OFDM with BPSK/QPSK/16QAM/64QAM for802.11a/n;
Operating Frequency
Range
WIFI 5G Band Mode Frequency
Range(MHz
)
Number of
channels
UNII
Band I 802.11a/n(HT20) 5180-5240
4
UNII
Band III 802.11a/n(HT20) 5745-5825
5
Transmit Power Max 13.86 dBm for UNII Band I
16.27dBm for UNII Band III
Antenna Type Integral antenna via a SMAconnector

6

Frequency and Channel list for 802.11b/g/n(HT20):
Channel Frequency
(MHz) Channel Frequency (MHz) Channel Frequency (MHz)
1 2412 5 2432 9 2452
2 2417 6 2437 10 2457
3 2422 7 2442 11 2462
4 2427 8 2447

Wifi 5G with UNII BandI
Frequency and Channel list for802.11a/n(HT20):
Channel Frequency Channel Frequency Channel Frequency
(MHz) (MHz) (MHz)
36 5180 44 5220

40 5200 48 5240

Wifi 5G with UNII Band III
Frequency and Channel list for802.11a/n(HT20):
Channel Frequency Channel Frequency Channel Frequency
(MHz) (MHz) (MHz)
149 5745 157 5785 165 5825
153 5765 161 5805


11

7. Pin Assignments
7.1 Pin Outline
< TOP VIEW >
7.2 Pin Definition
NO Name Type Description
1GND － Groundconnections
2_ANT I/O RF I/O port
3GND － Groundconnections
4FM_RX
I FM radio RF input antennaport
5NC － Floating (Don’t connected toground)
6_WAKE
I HOST wake-up Bluetoothdevice
7_HOST_WAKE
O wake-upHOST
8NC － Floating (Don’t connected toground)
9VBAT
P Main power voltage sourceinput
10 XTAL_IN
I Crystal input
11 XTAL_OUT
O Crystaloutput
12 WL_REG_ON
I Internal regulators powerenable/disable
13 WL_HOST_WAKE
O WLAN to wake-up HOST

12

14 SDIO_DATA_2 I/O SDIO data line 2
15 SDIO_DATA_3 I/O SDIO data line 3
16 SDIO_DATA_CMD I/O SDIO command line
17 SDIO_DATA_CLK I/O SDIO clock line
18 SDIO_DATA_0 I/O SDIO data line 0
19 SDIO_DATA_1 I/O SDIO data line 1
20 GND － Groundconnections
21 VIN_LDO_OUT
P Internal Buck voltage generationpin
22 VDDIO
P I/O Voltage supply input
23 VIN_LDO
P Internal Buck voltage generationpin
24 LPO
I External Low Power Clock input(32.768KHz)
25 PCM_OUT I/O PCM Data output
26 PCM_CLK I/O PCM clock
27 PCM_IN I/O PCM data input
28 PCM_SYNC I/O PCM sync signal
29 NC － Floating (Don’t connected toground)
30 NC － Floating (Don’t connected toground)
31 GND － Groundconnections
32 NC － Floating (Don’t connected toground)
33 GND － Groundconnections
34 RST_N
I Low asserting reset for Bluetoothcore
35 NC － Floating (Don’t connected toground)
36 GND － Groundconnections
37 NC － Floating (Don’t connected toground)
38 NC － Floating (Don’t connected toground)
39 NC － Floating (Don’t connected toground)
40 NC － Floating (Don’t connected toground)
41 UART_RTS_N
O FM UART interface
42 UART_TXD
O FM UARTinterface
43 UART_RXD
I FM UARTinterface
44 UART_CTS_N
I FM UART interface
45 TP1
O FMAnalog AUDIO left output
46 TP2
O FM Analog AUDIO rightoutput
47 TP3 (NC) － Floating (Don’t connected toground)

13

8. Dimensions
8.1 Physical Dimensions
(Unit: mm)
< TOP VIEW> < Side View >
< TOP VIEW >

14

8.2 Layout Recommendation
(Unit: mm)
< TOP VIEW >

FCC warning:
The modular transmitter have its own RF shielding, but this 1mm of the hole can only
ensure 6th harmonic of 2.4G and 3th harmonic of 5G not coupling theoretically. Therefore,
this is a limited module. This module only use for the Lighthouse LED Video Display
Screen, and the model of the Lighthouse LED Video Display Screen is A2.5-89 , A2.5-
118, A2.5-104.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Any Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate theequipment.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
-Reorient or relocate the receivingantenna.
-Increase the separation between the equipment andreceiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-Consult the dealer or an experienced radio/TV technician forhelp.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & yourbody.
This module is designed to comply with the FCC statement, FCC ID is: 2ARRD-AP6330.
The host system using this module, should have label in a visible area indicated the
following texts: "Contains FCC ID:2ARRD-AP6330".