Amplitec C10 Series User manual

RF Connector N-Female
Switch Power Switch
Cooling Heatsink Convection Cooling
Dimensions (D x W xH ) 209*133*41（mm）
Weight < 1.5 Kg
Installation Type Wall Installation
Environment Conditions IP40
Humidity < 90%
Operating Temperature -10℃~55℃

Items Specification
C10/C15/C20-CDMA UL:824~849MHz DL:869~894MHz
C10/C15/C20-GSM UL:890~915MHz DL:935~960MHz
C10/C15/C20-DCS UL:1710~1775MHz DL:1805~1870MHz
C10/C15/C20-PCS UL:1850~1900MHz DL:1930~1980MHz
C10/C15/C20-WCDMA UL:1920~1980MHz DL:2110~2170MHz
C10-GD UL:890~915MHz/1710~1775MHz
DL:935~960MHz/1805~1870MHz
C10-CP UL:824~849MHz/1850~1900MHz
DL:869~894MHz/1930~1980MHz
C10-GW UL:890~915MHz/1920~1980MHz
DL:935~960MHz/2110~2170MHz
Frequency
Range
C10-CW UL:824~849MHz/1920~1980MHz
DL:869~894MHz/2110~2170MHz
UL C10:≧60 dB ;C15/C20: ≧65dB
Max.Gain DL C10:≧60 dB ;C15: ≧65dB; C20 ≧70dB
Automatic Level Control ≧20dB
Gain Flatness CDMA/GSM≦8dB ; DCS/PCS≦10dB ;
WCDMA≦5dB
UL C10/ C15:≧10 dBm ; C20: ≧15 dBm
Output Power DL C10≧10 dBm; C15:≧15 dBm ; C20: ≧20
dBm
9KHz~1GHz ≦ -36dBm@ 3KHz;
Intermodulation
Products 1GHz~12.75GHz ≦ -30dBm@ 3KHz;
9KHz~1GHz ≦ -36dBm @ 3KHz
Spurious
Emission 1GHz~12.75GHz ≦ -30dBm @ 3KHz
Noise Figure Single band≦6dB; Dual band≦8dB
VSWR Single band≦2; Dual band≦2.5
Group Delay ≦0.5μs
DC Supply 9V2A (AC:90V~265V)
Power LED DC ON/OFF
Normal ：At the edge of green and orange
Low：Green
LED Indication Alarm LED：（Input
Signal Levels） High：>1-5dB range: Orange; >20dB: Red

Series Item Specification Quantity Remarks
1 Expanding plug M7 4 Accessories
2 Tapping screw M6*40 4 Accessories
3 Spinner 1
4 Waterproof tape 1
5 Ruler 1 Measurement and installation
of hole
6 Percussion drill 1 Drilling on wall

Status Definition of ALARM
Meaning: working in linearity, not Max. output
power and Power on. green
Attention: Input signals may be not enough
Meaning: overloading or self oscillation, strong
input signals
red
Attention: input signal level is too high or the
space of donor antenna and service antenna is
not enough. Please adjust the isolation, if the red
light still turning on that means over accepting of
donor antenna or strong interference, then
please adjust the place of donor antenna.
orange Meaning: working at Max. output power and ALC
is working.
off Repeater breaks down