Analog Devices ADSP-BF518F EZ-Board User manual

ADSP-BF518F EZ-BoardTM
Evaluation System Manual
Revision 1.0, January 2009
Part Number
82-000217-01
Analog Devices, Inc.
One Technology Way
Norwood, Mass. 02062-9106

Copyright Information
© 2009 Analog Devices, Inc., ALL RIGHTS RESERVED. This docu-
ment may not be reproduced in any form without prior, express written
consent from Analog Devices, Inc.
Printed in the USA.
Disclaimer
Analog Devices, Inc. reserves the right to change this product without
prior notice. Information furnished by Analog Devices is believed to be
accurate and reliable. However, no responsibility is assumed by Analog
Devices for its use; nor for any infringement of patents or other rights of
third parties which may result from its use. No license is granted by impli-
cation or otherwise under the patent rights of Analog Devices, Inc.
Trademark and Service Mark Notice
The Analog Devices icon bar and logo, VisualDSP++, the VisualDSP++
logo, Blackfin, the Blackfin logo, the CROSSCORE logo, EZ-KIT Lite,
and EZ-Extender are registered trademarks of Analog Devices, Inc.
EZ-Board is a trademark of Analog Devices, Inc.
All other brand and product names are trademarks or service marks of
their respective owners.

Regulatory Compliance
The ADSP-BF518F EZ-Board is designed to be used solely in a laboratory
environment. The board is not intended for use as a consumer end prod-
uct or as a portion of a consumer end product. The board is an open
system design which does not include a shielded enclosure and therefore
may cause interference to other electrical devices in close proximity. This
board should not be used in or near any medical equipment or RF devices.
The ADSP-BF518F EZ-Board is currently being processed for certifica-
tion that it complies with the essential requirements of the European
EMC directive 89/336/EEC amended by 93/68/EEC and therefore carries
the “CE” mark.
The EZ-Board evaluation system contains ESD (electrostatic discharge)
sensitive devices. Electrostatic charges readily accumulate on the human
body and equipment and can discharge without detection. Permanent
damage may occur on devices subjected to high-energy discharges. Proper
ESD precautions are recommended to avoid performance degradation or
loss of functionality. Store unused EZ-Board boards in the protective ship-
ping package.

ADSP-BF518F EZ-Board Evaluation System Manual v
CONTENTS
PREFACE
Purpose of This Manual .................................................................. xv
Intended Audience .......................................................................... xv
Manual Contents ........................................................................... xvi
What’s New in This Manual ........................................................... xvi
Technical or Customer Support ..................................................... xvii
Supported Processors ..................................................................... xvii
Product Information .................................................................... xviii
Analog Devices Web Site ........................................................ xviii
VisualDSP++ Online Documentation ....................................... xix
Technical Library CD ............................................................... xix
Related Documents ................................................................... xx
Notation Conventions .................................................................... xxi
USING ADSP-BF518F EZ-BOARD
Package Contents .......................................................................... 1-3
Default Configuration ................................................................... 1-4
EZ-Board Installation ................................................................... 1-4
EZ-Board Session Startup .............................................................. 1-6

CONTENTS
vi ADSP-BF518F EZ-Board Evaluation System Manual
Evaluation License Restrictions ..................................................... 1-8
Memory Map ............................................................................... 1-9
SDRAM Interface ....................................................................... 1-11
Parallel Flash Memory Interface .................................................. 1-11
eMMC Interface ......................................................................... 1-12
SD Interface ............................................................................... 1-13
SPI Interface .............................................................................. 1-13
Parallel Peripheral Interface (PPI) ................................................ 1-15
Rotary Encoder Interface ............................................................ 1-15
Ethernet Interface ....................................................................... 1-16
Audio Interface ........................................................................... 1-17
ADC Interface ............................................................................ 1-18
UART Interface .......................................................................... 1-19
RTC Interface ............................................................................ 1-20
LEDs and Push Buttons .............................................................. 1-21
JTAG Interface ........................................................................... 1-22
Land Grid Array ......................................................................... 1-22
Expansion Interface II ................................................................. 1-23
Power Measurements .................................................................. 1-24
Power-On-Self Test ..................................................................... 1-24
Example Programs ...................................................................... 1-25
Background Telemetry Channel .................................................. 1-25
Reference Design Information ..................................................... 1-25

ADSP-BF518F EZ-Board Evaluation System Manual vii
CONTENTS
ADSP-BF518F EZ-BOARD HARDWARE REFERENCE
System Architecture ...................................................................... 2-2
Programmable Flags ...................................................................... 2-3
Push Button and Switch Settings ................................................... 2-7
Boot Mode Select Switch (SW1) .............................................. 2-8
PB Enable Switch (SW2) ......................................................... 2-8
Flash Enable Switch (SW3) ...................................................... 2-9
SPORT1 Enable Switch (SW4) ................................................ 2-9
MIC Gain Switch (SW5) ....................................................... 2-10
Mic/HP LPBK, Audio Mode Switch (SW6) ........................... 2-10
Ethernet Port 1 Configuration Switch (SW7) ......................... 2-11
Ethernet Configuration Switch (SW8) ................................... 2-11
UART Setup Switch (SW10) ................................................. 2-12
Reset Push Button (SW11) .................................................... 2-12
Programmable Flag Push Buttons (SW12–13) ........................ 2-12
Rotary Encoder with Momentary Switch (SW14) .................. 2-13
SPORT0 ENBL Switch (SW15) ............................................. 2-13
SPI/TWI Switch (SW16) ....................................................... 2-13
Ethernet Mode Switch (SW17) .............................................. 2-14
Ethernet Port 2 Configuration Switch (SW18) ....................... 2-14
Encoder Enable Switch (SW19) ............................................. 2-14
eMMC Enable Switch (SW20–21) ......................................... 2-15
ADC Loopback Switches (SW22–23) ..................................... 2-15
Jumpers ...................................................................................... 2-16

CONTENTS
viii ADSP-BF518F EZ-Board Evaluation System Manual
Flash WP Jumper (JP3) ......................................................... 2-17
ADC Range Jumper (JP4) ..................................................... 2-17
LED Select Jumpers (JP11–12) ............................................. 2-17
Ethernet Power Down Jumper (JP13) .................................... 2-17
OTP Flag Enable Jumper (JP14) ........................................... 2-18
MIC Select Jumper (JP15) .................................................... 2-18
SPI FLASH CS Enable Jumper (JP16) ................................... 2-18
ADC Channel Select Jumpers (JP17–28) ............................... 2-19
VDDINT Power Jumper (P8) ............................................... 2-19
VDDEXT Power Jumper (P9) ............................................... 2-19
VDDMEM Power Jumper (P10) ........................................... 2-20
VDDFLASH Power Jumper (P11) ......................................... 2-20
LEDs ......................................................................................... 2-21
GPIO LEDs (LED1–3) ......................................................... 2-22
Ethernet LEDs (LED4–8, LED10–12) .................................. 2-22
Reset LED (LED9) ............................................................... 2-22
Power LED (LED13) ............................................................ 2-23
Connectors ................................................................................. 2-24
Expansion Interface II Connector (J1) ................................... 2-25
RS-232 Connector (J2) ......................................................... 2-25
Power Connector (J3) ........................................................... 2-25
Dual Audio Connectors (J4–5) .............................................. 2-26
SMA Connectors (J7, J16–26) .............................................. 2-26
Battery Holder (J12) ............................................................. 2-26

ADSP-BF518F EZ-Board Evaluation System Manual ix
CONTENTS
SD Connector (J13) .............................................................. 2-26
Ethernet Connectors (J14–15) ............................................... 2-27
JTAG Connector (P1) ........................................................... 2-27
Expansion Interface II Connectors (P2 and P4) ...................... 2-27
Expansion Interface II Connector (P3) ................................... 2-28
DMAX Land Grid Array Connectors (P5–7) .......................... 2-28
Standalone Debug Agent Connector (ZP1) ............................ 2-29
ADSP-BF518F EZ-BOARD BILL OF MATERIALS
ADSP-BF518F EZ-BOARD SCHEMATIC
Title Page .................................................................................... B-1
Processor EBIU and Control ........................................................ B-2
Processor Power, Bypass Caps ....................................................... B-3
External Memory ......................................................................... B-4
ADC ........................................................................................... B-5
Audio Codec ................................................................................ B-6
Ethernet Switch ........................................................................... B-7
Ethernet Config/LEDs ................................................................. B-8
Ethernet Jacks .............................................................................. B-9
Rotary Encoder, JTAG, RS-232, RSI .......................................... B-10
Logic Analyzer Conn.................................................................. B-11
Push Buttons, Reset, LEDs ......................................................... B-12
Expansion Interface .................................................................... B-13
OTP and Dual Power ................................................................. B-14

CONTENTS
x ADSP-BF518F EZ-Board Evaluation System Manual
Power ......................................................................................... B-15
Series Terminators ...................................................................... B-16
INDEX

ADSP-BF518F EZ-Board Evaluation System Manual xi
PREFACE
Thank you for purchasing the ADSP-BF518F EZ-Board™, Analog
Devices, Inc. evaluation system for Blackfin®processors.
Blackfin processors embody a new type of embedded processor designed
specifically to meet the computational demands and power constraints of
today’s embedded audio, video, and communications applications. They
deliver breakthrough signal-processing performance and power efficiency
within a reduced instruction set computing (RISC) programming model.
Blackfin processors support a media instruction set computing (MISC)
architecture. This architecture is the natural merging of RISC, media
functions, and digital signal processing (DSP) characteristics. Blackfin
processors deliver signal-processing performance in a microprocessor-like
environment.
Based on the Micro Signal Architecture (MSA), Blackfin processors com-
bine a 32-bit RISC instruction set, dual 16-bit multiply accumulate
(MAC) DSP functionality, and eight-bit video processing performance
that had previously been the exclusive domain of very-long instruction
word (VLIW) media processors.

xii ADSP-BF518F EZ-Board Evaluation System Manual
The evaluation board is designed to be used in conjunction with the Visu-
alDSP++®development environment to test the capabilities of the
ADSP-BF518F Blackfin processors. The VisualDSP++ development envi-
ronment aids advanced application code development and debug, such as:
• Create, compile, assemble, and link application programs written
in C++, C, and ADSP-BF518F assembly
• Load, run, step, halt, and set breakpoints in application programs
• Read and write data and program memory
• Read and write core and peripheral registers
• Plot memory
Access to the ADSP-BF518F processor from a personal computer (PC) is
achieved through a USB port or an external JTAG emulator. The USB
interface of the standalone debug agent gives unrestricted access to the
ADSP-BF518F processor and evaluation board’s peripherals. Analog
Devices JTAG emulators offer faster communication between the host PC
and target hardware. To learn more about Analog Devices emulators and
processor development tools, go to http://www.analog.com/dsp/tools/.
The ADSP-BF518F EZ-Board provides example programs to demonstrate
the capabilities of the product.
LThe ADSP-BF518F EZ-Board installation is part of the Visu-
alDSP++ installation. As an EZ-KIT Lite, an EZ-Board is a
licensed product that offers an unrestricted evaluation license for
the first 90 days. For details about evaluation license restrictions
after the 90 days, refer to “Evaluation License Restrictions” on
page 1-8 and the VisualDSP++ Installation Quick Reference Card.

ADSP-BF518F EZ-Board Evaluation System Manual xiii
Preface
The board features:
• Analog Devices ADSP-BF518F Blackfin processor
DCore performance up to 400 MHz
DExternal bus performance up to 80 MHz
D176-pin LQFP package
D25 MHz crystal
• Programmable VDDINT core power
DAnalog Devices AD5258 TWI digital potentiometer
DAnalog Devices ADP1715 low dropout linear regulator
• Synchronous dynamic random access memory (SDRAM)
DMicron MT48LC32M16A2TG – 64 MB (32M x 16-bits)
• Parallel flash memory
DNumonyx M29W320EB – 4 MB (2M x 16-bits)
• eMMC flash memory
DMicron MTFC2GDKDM – 2 GB
• SPI flash memory
DNumonyx M25P16 – 16 Mb
• Analog audio interface
DAnalog Devices SSM2602 low-power audio codec
DOne stereo LINE OUT jack
DOne headphone LINE IN
DOne input MIC jack
DOne input stereo LINE IN jack

xiv ADSP-BF518F EZ-Board Evaluation System Manual
• Ethernet interface
DMicrel KSZ8893M PHY device
D10-BaseT and 100-BaseTX Ethernet controller
DAuto-MDIX
• ADC interface
DAnalog Devices AD7266 2 MSPS, 12-bit, 3-channel SAR
analog-to-digital converter
• Thumbwheel
DPanasonic EVQ-WKA001 rotary encoder
• Universal asynchronous receiver/transmitter (UART)
DADM3202 RS-232 line driver/receiver
DDB9 female connector
•LEDs
DThirteen LEDs: one board reset (red), three general-purpose
(amber), eight configurable ethernet LEDs (amber) and one
power (green)
• Push buttons
DThree push buttons: one reset, two programmable flags with
debounce logic
• Expansion interface II™
DNext generation of the expansion interface design, provides
access to most of the ADSP-BF518F processor signals
• Land grid array
DEasy probing of all port pins and most EBIU signals

ADSP-BF518F EZ-Board Evaluation System Manual xv
Preface
• Other features
DJTAG ICE 14-pin header
DBlackfin power measurement jumpers
For information about the hardware components of the EZ-Board, refer
to “ADSP-BF518F EZ-Board Hardware Reference” on page 2-1.
Purpose of This Manual
The ADSP-BF518F EZ-Board Evaluation System Manual provides instruc-
tions for installing the product hardware (board). The text describes
operation and configuration of the board components and provides guide-
lines for running your own code on the ADSP-BF518F EZ-Board.
Finally, a schematic and a bill of materials are provided as a reference for
future designs.
The product software installation is detailed in the VisualDSP++ Installa-
tion Quick Reference Card.
Intended Audience
The primary audience for this manual is a programmer who is familiar
with Analog Devices processors. This manual assumes that the audience
has a working knowledge of the appropriate processor architecture and
instruction set. Programmers who are unfamiliar with Analog Devices
processors can use this manual, but should supplement it with other texts
(such as the ADSP-BF51x Blackfin Processor Hardware Reference and
Blackfin Processor Instruction Set Reference) that describe your target
architecture.
Programmers who are unfamiliar with VisualDSP++ should refer to the
VisualDSP++ online Help and user’s or getting started guides. For the
locations of these documents, see “Related Documents”.

Manual Contents
xvi ADSP-BF518F EZ-Board Evaluation System Manual
Manual Contents
The manual consists of:
• Chapter 1, “Using ADSP-BF518F EZ-Board” on page 1-1
Describes EZ-Board functionality from a programmer’s perspective
and provides an easy-to-access memory map.
• Chapter 2, “ADSP-BF518F EZ-Board Hardware Reference” on
page 2-1
Provides information on the EZ-Board hardware components.
• Appendix A, “ADSP-BF518F EZ-Board Bill Of Materials” on
page A-1
Provides a list of components used to manufacture the EZ-Board.
• Appendix B, “ADSP-BF518F EZ-Board Schematic” on page B-1
Provides the resources to allow EZ-Board board-level debugging or
to use as a reference design. Appendix B is part of the online Help.
What’s New in This Manual
This is the first revision of the ADSP-BF518F EZ-Board Evaluation System
Manual.

ADSP-BF518F EZ-Board Evaluation System Manual xvii
Preface
Technical or Customer Support
You can reach Analog Devices, Inc. Customer Support in the following
ways:
• Visit the Embedded Processing and DSP products Web site at
http://www.analog.com/processors/technical_support
• E-mail tools questions to
[e-mail]
• E-mail processor questions to
[email protected]m (World wide support)
[email protected] (Europe support)
[email protected] (China support)
• Phone questions to 1-800-ANALOGD
• Contact your Analog Devices, Inc. local sales office or authorized
distributor
• Send questions by mail to:
Analog Devices, Inc.
One Technology Way
P.O. Box 9106
Norwood, MA 02062-9106
USA
Supported Processors
This evaluation system supports Analog Devices ADSP-BF518F Blackfin
embedded processors.

Product Information
xviii ADSP-BF518F EZ-Board Evaluation System Manual
Product Information
Product information can be obtained from the Analog Devices Web site,
VisualDSP++ online Help system, and a technical library CD.
Analog Devices Web Site
The Analog Devices Web site, www.analog.com, provides information
about a broad range of products—analog integrated circuits, amplifiers,
converters, and digital signal processors.
To access a complete technical library for each processor family, go to
http://www.analog.com/processors/technical_library. The manuals
selection opens a list of current manuals related to the product as well as a
link to the previous revisions of the manuals. When locating your manual
title, note a possible errata check mark next to the title that leads to the
current correction report against the manual.
Also note, MyAnalog.com is a free feature of the Analog Devices Web site
that allows customization of a Web page to display only the latest infor-
mation about products you are interested in. You can choose to receive
weekly e-mail notifications containing updates to the Web pages that meet
your interests, including documentation errata against all manuals.
MyAnalog.com provides access to books, application notes, data sheets,
code examples, and more.
Visit MyAnalog.com to sign up. If you are a registered user, just log on.
Your user name is your e-mail address.

ADSP-BF518F EZ-Board Evaluation System Manual xix
Preface
VisualDSP++ Online Documentation
Online documentation comprises the VisualDSP++ Help system, software
tools manuals, hardware tools manuals, processor manuals, Dinkum
Abridged C++ library, and FLEXnet License Tools software documenta-
tion. You can search easily across the entire VisualDSP++ documentation
set for any topic of interest.
For easy printing, supplementary Portable Documentation Format (.pdf)
files for all manuals are provided on the VisualDSP++ installation CD.
Each documentation file type is described as follows.
Technical Library CD
The technical library CD contains seminar materials, product highlights, a
selection guide, and documentation files of processor manuals, Visu-
alDSP++ software manuals, and hardware tools manuals for the following
processor families: Blackfin, SHARC, TigerSHARC, ADSP-218x, and
ADSP-219x.
To order the technical library CD, go to http://www.analog.com/proces-
sors/technical_library, navigate to the manuals page for your
processor, click the request CD check mark, and fill out the order form.
File Description
.chm Help system files and manuals in Microsoft help format
.htm or
.html
Dinkum Abridged C++ library and FLEXnet License Tools software documenta-
tion. Viewing and printing the .html files requires a browser, such as Internet
Explorer 6.0 (or higher).
.pdf VisualDSP++ and processor manuals in PDF format. Viewing and printing the
.pdf files requires a PDF reader, such as Adobe Acrobat Reader (4.0 or higher).

Product Information
xx ADSP-BF518F EZ-Board Evaluation System Manual
Data sheets, which can be downloaded from the Analog Devices Web site,
change rapidly, and therefore are not included on the technical library
CD. Technical manuals change periodically. Check the Web site for the
latest manual revisions and associated documentation errata.
Related Documents
For information on product related development software, see the follow-
ing publications.
Table 1. Related Processor Publications
Title Description
ADSP-BF512/ADSP-BF514/ADSP-BF516/ADSP-
BF518 Blackfin Embedded Processor Preliminary
Data Sheet
General functional description, pinout, and
timing of the processor.
ADSP-BF51x Blackfin Processor Hardware Refer-
ence
Description of internal processor architec-
ture and all register functions.
Blackfin Processor Programming Reference Description of all allowed processor assem-
bly instructions.
Table 2. Related VisualDSP++ Publications
Title Description
ADSP-BF518F EZ-Board Evaluation System Man-
ual
Description of the hardware capabilities of
the evaluation system; description of how to
access these capabilities in the VisualDSP++
environment.
VisualDSP++ User’s Guide Description of VisualDSP++ features and
usage.
VisualDSP++ Assembler and Preprocessor Manuals Description of the assembler function and
commands.
VisualDSP++ C/C++ Complier and Library Man-
ual for Blackfin Processors
Description of the complier function and
commands for Blackfin processors.