Analog Devices ADSP-BF561 EZ-KIT Lite User guide

a
ADSP-BF561 EZ-KIT Lite®
Evaluation System Manual
Revision 3.3, July 2012
Part Number
82-000811-01
Analog Devices, Inc.
One Technology Way
Norwood, Mass. 02062-9106

Copyright Information
© 2012 Analog Devices, Inc., ALL RIGHTS RESERVED. This docu-
ment may not be reproduced in any form without prior, express written
consent from Analog Devices, Inc.
Printed in the USA.
Disclaimer
Analog Devices, Inc. reserves the right to change this product without
prior notice. Information furnished by Analog Devices is believed to be
accurate and reliable. However, no responsibility is assumed by Analog
Devices for its use; nor for any infringement of patents or other rights of
third parties which may result from its use. No license is granted by impli-
cation or otherwise under the patent rights of Analog Devices, Inc.
Trademark and Service Mark Notice
The Analog Devices logo, Blackfin, CrossCore, EngineerZone,
EZ-Extender, EZ-KIT Lite, and VisualDSP++ are registered trademarks of
Analog Devices, Inc.
All other brand and product names are trademarks or service marks of
their respective owners.

Regulatory Compliance
The ADSP-BF561 EZ-KIT Lite is designed to be used solely in a labora-
tory environment. The board is not intended for use as a consumer end
product or as a portion of a consumer end product. The board is an open
system design which does not include a shielded enclosure and therefore
may cause interference to other electrical devices in close proximity. This
board should not be used in or near any medical equipment or RF devices.
The ADSP-BF561 EZ-KIT Lite has been certified to comply with the
essential requirements of the European EMC directive 89/336/EEC
amended by 93/68/EEC and therefore carries the “CE” mark.
The ADSP-BF561 EZ-KIT Lite has been appended to Analog Devices,
Inc. Technical File (TCF) referenced ‘DSPTOOLS1’ dated
December 21, 1997 and was awarded CE Certification by an appointed
European Competent Body as listed below.
Technical Certificate No: Z600ANA1.016
Issued by: Technology International (Europe) Limited
60 Shrivenham Hundred Business Park
Shrivenham, Swindon, SN6 8TY, UK
The EZ-KIT Lite evaluation system contains ESD (electrostatic discharge)
sensitive devices. Electrostatic charges readily accumulate on the human
body and equipment and can discharge without detection. Permanent
damage may occur on devices subjected to high-energy discharges. Proper
ESD precautions are recommended to avoid performance degradation or
loss of functionality. Store unused EZ-KIT Lite boards in the protective
shipping package.

ADSP-BF561 EZ-KIT Lite Evaluation System Manual v
CONTENTS
PREFACE
Product Overview ........................................................................... xi
Purpose of This Manual ................................................................ xiii
Intended Audience ........................................................................ xiii
Manual Contents ........................................................................... xiv
What’s New in This Manual ........................................................... xiv
Technical Support ........................................................................... xv
Supported Processors ...................................................................... xvi
Product Information ...................................................................... xvi
Analog Devices Web Site .......................................................... xvi
EngineerZone .......................................................................... xvii
Related Documents ...................................................................... xviii
Notation Conventions .................................................................. xviii
USING THE ADSP-BF561 EZ-KIT LITE
Package Contents .......................................................................... 1-2
Default Configuration ................................................................... 1-3
CCES Install and Session Startup .................................................. 1-4
Session Startup ........................................................................ 1-6

Contents
vi ADSP-BF561 EZ-KIT Lite Evaluation System Manual
VisualDSP++ Install and Session Startup ....................................... 1-8
CCES Evaluation License ........................................................... 1-10
VisualDSP++ Evaluation License ................................................. 1-11
Memory Map ............................................................................. 1-11
LEDs and Push Buttons .............................................................. 1-14
Audio Interface ........................................................................... 1-15
Video Interface ........................................................................... 1-16
Board Design Database ............................................................... 1-17
Example Programs ...................................................................... 1-18
Flash Programming Utility .......................................................... 1-18
ADSP-BF561 EZ-KIT LITE HARDWARE REFERENCE
System Architecture ...................................................................... 2-2
External Bus Interface Unit ..................................................... 2-3
SPORT Audio Interface .......................................................... 2-3
SPI Interface ........................................................................... 2-3
Programmable Flags ................................................................ 2-4
PPI Interfaces ......................................................................... 2-5
Video Output (PPI1) .......................................................... 2-7
Video Input (PPI0) ............................................................. 2-7
UART Port ............................................................................. 2-8
Expansion Interface ................................................................. 2-8
JTAG Emulation Port ............................................................. 2-9

ADSP-BF561 EZ-KIT Lite Evaluation System Manual vii
Contents
Jumper and DIP Switch Settings .................................................. 2-10
Video Configuration Switch (SW2) ....................................... 2-10
Boot Mode Switch (SW3) ...................................................... 2-11
Push Button Enable Switch (SW4) ......................................... 2-12
PPI Clock Select Switch (SW5) .............................................. 2-13
Test DIP Switches (SW10 and SW11) .................................... 2-13
Audio Enable Switch (SW12) ................................................ 2-13
SPIS1/SPISS Select (SW13) ................................................... 2-14
Video Encoder Clock Select Jumper (JP1) .............................. 2-14
VDDINT Select Jumpers (JP2 and JP3) ................................. 2-14
UART Loop Jumper (P1) ....................................................... 2-15
LEDs and Push Buttons .............................................................. 2-15
Reset Push Button (SW1) ...................................................... 2-16
Programmable Flag Push Buttons (SW6–9) ............................ 2-16
Power LED (LED1) ............................................................... 2-16
Reset LED (LED2) ................................................................ 2-17
USB Monitor LED (ZLED3) ................................................. 2-17
User LEDs (LED5–12, LED13–20) ....................................... 2-17
Connectors ................................................................................. 2-18
Expansion Interface (J1–3) .................................................... 2-19
Audio (J4 and J5) .................................................................. 2-19
Video (J6) ............................................................................. 2-20
Power (J7) ............................................................................. 2-20
RS-232 (P2) .......................................................................... 2-20

Contents
viii ADSP-BF561 EZ-KIT Lite Evaluation System Manual
SPORT1 (P3) ....................................................................... 2-21
SPI (P5) ................................................................................ 2-21
USB Debug Agent Connector (ZJ1) ...................................... 2-21
JTAG (ZP4) .......................................................................... 2-22
ADSP-BF561 EZ-KIT LITE BILL OF MATERIALS
ADSP-BF561 EZ-KIT LITE SCHEMATIC
INDEX

ADSP-BF561 EZ-KIT Lite Evaluation System Manual ix
PREFACE
Thank you for purchasing the ADSP-BF561 EZ-KIT Lite®, Analog
Devices, Inc. evaluation system for Blackfin®processors.
Blackfin processors embody a type of embedded processor designed specif-
ically to meet the computational demands and power constraints of
today’s embedded audio, video, and communications applications. They
deliver breakthrough signal-processing performance and power efficiency
within a reduced instruction set computing (RISC) programming model.
Blackfin processors support a media instruction set computing (MISC)
architecture. This architecture is the natural merging of RISC, media
functions, and digital signal processing (DSP) characteristics. Blackfin
processors deliver signal-processing performance in a microprocessor-like
environment.
Based on the Micro Signal Architecture (MSA), Blackfin processors com-
bine a 32-bit RISC instruction set, dual 16-bit multiply accumulate
(MAC) DSP functionality, and eight-bit video processing performance
that had previously been the exclusive domain of very-long instruction
word (VLIW) media processors.

x ADSP-BF561 EZ-KIT Lite Evaluation System Manual
The evaluation board is designed to be used in conjunction with the
CrossCore®Embedded Studio (CCES) and VisualDSP++®development
environments to test the capabilities of the ADSP-BF561 Blackfin proces-
sors. The VisualDSP++ development environment gives you the ability to
perform advanced application code development and debug, such as:
• Create, compile, assemble, and link application programs written
in C++, C, and ADSP-BF561 assembly
• Load, run, step, halt, and set breakpoints in application programs
• Read and write data and program memory
• Read and write core and peripheral registers
• Plot memory
Access to the ADSP-BF561 processor from a personal computer (PC) is
achieved through a USB port or an optional JTAG emulator. The USB
interface gives unrestricted access to the ADSP-BF561 processor and the
evaluation board peripherals. Analog Devices JTAG emulators offer faster
communication between the host PC and target hardware. Analog Devices
carries a wide range of in-circuit emulation products. To learn more about
Analog Devices emulators and processor development tools, go to
http://www.analog.com/dsp/tools.
The ADSP-BF561 EZ-KIT Lite provides example programs to demon-
strate the capabilities of the evaluation board.