Analog Devices Advantiv EVAL-ADV7611EB1Z Quick start guide

Eval Note ADV7611/ Eval Note
Pr.A
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or
other rights of third parties that may result from its use. Specifications subject to change without
notice. No license is granted by implication or otherwise under any patent or patent rights of
Analog Devices. Trademarks and registered trademarks are the property of their respective
owners.
Evaluation Note
ADV7611 Evaluation
Board Rev. B
October 2010
Pr. A

Eval Note
Rev. PrA Page 2 of 31
Table of Contents
Table of Contents........................................................................................................................................... 2
1.Introduction........................................................................................................................................... 3
2.Evaluation Kit....................................................................................................................................... 3
3.Initial Hardware Configuration............................................................................................................. 4
4.Initial Hardware Configuration............................................................................................................. 5
4.1XRC Installation................................................................................................................................ 5
4.2Loading/Unloading Boards............................................................................................................... 6
4.2.1Loading a Board .......................................................................................................................... 6
4.2.2Unloading a Board....................................................................................................................... 6
4.3Running Scripts................................................................................................................................. 7
4.4Other XRC Features.......................................................................................................................... 8
4.4.1Register Control........................................................................................................................... 8
5.The ADV7611 Evaluation Platform in Depth....................................................................................... 9
5.1Hardware Overview .......................................................................................................................... 9
5.1.1Connectors................................................................................................................................... 9
5.1.2Jumpers........................................................................................................................................ 9
5.1.3Switches & Buttons..................................................................................................................... 9
5.1.4Miscellaneous.............................................................................................................................. 9
5.2Using the ADV7611 Evaluation Platform........................................................................................11
5.2.1Connecting an Input Video Source.............................................................................................11
5.2.2Connecting to a Video Sink........................................................................................................11
5.2.3Connecting an Input Audio Source.............................................................................................11
5.2.4Connecting a headphone.............................................................................................................11
5.2.5Updating the Software Driver.....................................................................................................11
5.2.6Interfacing with the Software Driver......................................................................................... 12
6.Appendix 1 – Schematics.................................................................................................................... 13
7.Appendix 2 – Layout .......................................................................................................................... 22
8.Appendix 3 – Flash Magic.................................................................................................................. 28
9.Appendix 4 – Downloading from FTP ............................................................................................... 29
10.Appendix 5 – Software Driver Controls............................................................................................. 30

Eval Note
Rev. PrA Page 3 of 31
1. Introduction
This evaluation note is intended to provide application support for the ADV7611 evaluation board. It also
provides details on the set up and manual configuration of the evaluation board. Software drivers are
available for this evaluation board - a separate user guide is available for these software drivers.
This note applies to board revision B.
2. Evaluation Kit
The ADV7611 evaluation board kit should consist of the following:
1. ADV7611 Evaluation Board
2. 7.5V DC power supply module
3. USB cable

Eval Note
Rev. PrA Page 4 of 31
3. Initial Hardware Configuration
The ADV7611 evaluation board is a standalone evaluation platform used to demonstrate all features of the
ADV7611 receiver. To assemble the platform, connect the female connector of the 7.5V DC power supply
module supplied with the evaluation kit to the motherboard power connector, J8. To turn the evaluation
platform on, flick the power switch (S5) to position “ON”. The green power LED (D8) should light.
Once the board is powered up, connect the USB cable supplied with the evaluation kit to USB connector,
J1. The platform should now resemble Figure 1 and is ready to use.
Figure 1 - ADV7611 Evaluation Platform

Eval Note
Rev. PrA Page 5 of 31
4. Initial Hardware Configuration
4.1 XRC Installation
1. Run ADI_Install_XRC_x file (where x is the version number to be installed e.g. 1.5)
2. Review the license agreement and click “I Agree” if the terms of the agreement are acceptable
3. Select the desired access links – desktop shortcut and/or start menu shortcut (see Figure 2)
Figure 2 - Installation Options
4. Press “Next>”
5. Select the desired installation folder (see Figure 3)
Figure 3 - Installation Folder
6. Press “Install”
7. When the install has completed, press “Close”

Eval Note
Rev. PrA Page 6 of 31
4.2 Loading/Unloading Boards
4.2.1 Loading a Board
The following steps must be performed to start a new XRC session by loading a new board.
1. Click “Choose Board…”
2. From the Board Selector window, select your attached system e.g. “ADV7611” as RX, “None” for
MotherBoard and “ADV7511_ADV7341” for TX.
3. Click “Load”
Note: If the board is standalone, select the board in whichever window it is populated under (i.e. RX,
Motherboard, TX) and leave the other windows at “None”.
Figure 4 - Board Selector
4.2.2 Unloading a Board
The following steps must be performed to end an XRC session by unloading the selected board.
1. Select Files -> Unload Boards

Eval Note
Rev. PrA Page 7 of 31
4.3 Running Scripts
Scripts can be run by either of the following options:
1. Select Scripts -> Project Name e.g. ADV7611
2. Follow the script tree as outlined in the expanding menus (see Figure 5)
1. Select Scripts -> Run Script
2. Open the script folder of the desired project
3. Select the desired script and click “Open”
Please be patient as the script may take several seconds to run. Successful download of the script is
notified by the green light at the bottom of the screen flashing twice.
Figure 5 - XRC Script Tree

Eval Note
Rev. PrA Page 8 of 31
4.4 Other XRC Features
4.4.1 Register Control
The following steps must be performed to use XRC Register Control:
1. Select Tools -> Register Control
2. Enter the Device Address in HEX (see Figure 6)
3. Enter the desired register address in HEX
4. Press the “Write” button to write a value to the selected register
5. Press the “Read” button to read a value from the selected register
Figure 6 - register control window

Eval Note
Rev. PrA Page 9 of 31
5. The ADV7611 Evaluation Platform in Depth
5.1 Hardware Overview
The following features of the ADV7611 evaluation board should be noted
5.1.1 Connectors
1. 1 x HDMI inputs (J2)
2. 1 x HDMI output (J9)
3. 1 x UART connector (J7)
4. 1 x USB connector (J1)
5. 1 x audio output (U58)
6. 1 x S-video output (p5)
7. 1 x CVBS output (p3)
8. 1 x component (p4)
9. 1 x AV output connector (P7
5.1.2 Jumpers
1. MCU boot ROM location (K7) – default position ‘B’
2. MCU reset (K8) – default position ‘not inserted’
3. USB MCU (K6)
4. I2C switch (K5)
5. MCU I2C (SDA, SCL) – default position inserted
6. Audio reset (J3)
7. Microcontroller reset control (K9) – default position ‘not inserted’
8. INT 2 reset (K1, K2)
5.1.3 Switches & Buttons
1. ON/OFF (S5)
2. Software enable/disable (S3)
3. DUT reset (S1)
4. MCU reset (S4)
5. global reset (S2)
6. Software driver buttons (S_UP, S_DOWN, S_LEFT, S_RIGHT, S_SELECT, S_BACK )
5.1.4 Miscellaneous
1. 1x 20 way connectors (J6)
2. 1 x 12 way connectors (J5)
3. Software driver LEDS (LED1, LED2, LED3, LED4, LED5, LED6)
4. Audio channel LEDS (AUD_CH1, AUD_CH2, AUD_CH3,AUD_CH4)
5. I2C header (P1)

Eval Note
Rev. PrA Page 10 of 31
Figure 7 – ADV7611 Evaluation Platform
ADV7341
ADV7611
ADV7511
ADV7341
RS-232 USB
POWER
SUPPLY
HDMI
INPUT
AUDIO
OUTPUT
YPrPb
OUTPUT
HDMI
OUTPUT

Eval Note
Rev. PrA Page 11 of 31
5.2 Using the ADV7611 Evaluation Platform
5.2.1 Connecting an Input Video Source
To connect an input video source to the ADV7611 evaluation board, use a HDMI cable and the input
HDMI connector; J2. Do not use excessive force when connecting or disconnecting the cable as this may
result in damage to the evaluation board.
5.2.2 Connecting to a Video Sink
To connect the ADV7611 evaluation board to a video sink, use a HDMI cable and the output HDMI
connector; J9. Do not use excessive force when connecting or disconnecting the cable as this may result in
damage to the evaluation board.
5.2.3 Connecting an Input Audio Source
To connect an input audio source to the ADV7611 evaluation board, use a TOSlink cable and the input
audio connector; J2.
5.2.4 Connecting a headphone
To use a headphone, connect the headphone to connector HP2OUT1.
5.2.5 Updating the Software Driver
To download updated software driver code to the microcontroller used on the ADV7611 evaluation board,
please perform the following steps
1. Power off the board
2. Insert jumper K9
3. Ensure jumper K7 is in position A
4. Ensure that jumper K8 (MCU RESET) is not inserted
5. Connect a serial cable between the computer to be used for the download and the UART connector
(J7), on the ADV7611 evaluation board
6. Power on the board by moving the ON/OFF switch (S5) to position ON.
7. Start the Flashmagic download by pressing “Start”. For information on where to obtain and how to
use the Flashmagic tool, please see Appendix 3 – Flash Magic.
8. When the download has completed, power off the board.
9. Remove jumper K9.
10. Ensure jumper K7 is in position B.
11. Power on the board by moving the ON/OFF switch (S5) to position ON.
If the Flashmagic tool gives a warning, please check the setup and jumper positions carefully.

Eval Note
Rev. PrA Page 12 of 31
5.2.6 Interfacing with the Software Driver
Jumper K8, when inserted, pulls the microcontroller reset low. To use the software driver, please ensure
that K8 is removed.
To stop and start the software driver (e.g. to allow access to the I2C over XRC), toggle the SW_ENABLE
switch on the evaluation board. When disabled, the driver will send the message “REP: Driver Disabled”.
When enabled, the driver will send the message “REP: Driver Enabled” and any status updates will be
displayed.
12. Please see the software driver documentation for the functions performed by software driver
buttons (S_UP, S_DOWN, S_LEFT, S_RIGHT, S_SELECT, S_BACK ) and LEDS (LED1, LED2,
LED3, LED4, LED5, LED6). To enable the software driver, switch the software enable switch (S10) to
SW_ENABLE. To disable the software driver, switch the software enable switch (S3) away from
SW_ENABLE.
For information on the latest software driver, please contact your FAE or email
[email protected].

Eval Note
Rev. PrA Page 13 of 31
6. Appendix 1 – Schematics
Figure 8 HDMI Inputs Schematics Page

Eval Note
Rev. PrA Page 14 of 31
Figure 9: USB + Reset Circuitry Schematics Page

Eval Note
Rev. PrA Page 15 of 31
Figure 10: ADV7611 Schematics Page

Eval Note
Rev. PrA Page 16 of 31
Figure 11: Power Schematics Page 1 of 2

Eval Note
Rev. PrA Page 17 of 31
Figure 12: Power Schematics Page 2 of 2

Eval Note
Rev. PrA Page 18 of 31
Figure 13: Microcontroller Schematics Page

Eval Note
Rev. PrA Page 19 of 31
Figure 14: Encoder Schematics Page

Eval Note
Rev. PrA Page 20 of 31
Figure 15: HDMI TX Schematics Page