Analog Devices DC2629A Quick setup guide

1
DEMO MANUAL DC2629A
Rev. 0
DESCRIPTION
LTC3310S
5V, 10A Synchronous Step Down
Silent Switcher in 3mm x3mm LQFN
Demonstration Circuit DC2629A features the LTC
®
3310S
10A, Low Voltage, Synchronous Step-Down Silent
Switcher
®
2 operating as a 2MHz 3.3V to 1.2V 10A buck
regulator. The LTC3310S supports output voltages from
0.5V to VIN with operating frequencies from 500kHz up
to 5MHz. The LTC3310S is a compact, ultralow emission,
high efficiency, and high speed synchronous monolithic
step-down switching regulator. The integrated bypass
capacitors optimize all the fast current loops and make it
easier to minimize EMI/EMC emissions by reducing layout
sensitivity. Fast minimum on-time of 35ns enables high
VIN to low VOUT conversion at high frequency.
DC2629A is set up to run in Forced Continuous Mode
with a 2MHz switching frequency but can be configured
to Pulse Skip Mode and different switching frequencies.
RT is connected to VIN which sets the MODE/SYNC pin
as an input and allows the LTC3310S to sync from an
external clock. Connecting the MODE/SYNC pin to V
IN
sets the mode to Forced Continuous Mode and connecting
the MODE/SYNC pin to GND sets the mode to Pulse Skip
Mode. The Efficiency vs. Load graph shows the efficiency
All registered trademarks and trademarks are the property of their respective owners.
PERFORMANCE SUMMARY
and the power loss of the circuit with a 3.3V input in
forced continuous mode operation.
The DC2629A also has an EMI filter to reduce conducted
EMI. This EMI filter can be included by applying the input
voltage at the VIN EMI terminal. The EMI performance of
the board is shown in the EMI TEST RESULTS section.
The red lines in the EMI performance graphs illustrate
the CISPR25 Class 5 peak limits for the conducted and
radiated emission tests.
The LTC3310S data sheet gives a complete description of
the part, operation and application information. The data
sheet must be read in conjunction with this demo. The
LTC3310S is assembled in a 3mm x 3mm LQFN package
with exposed pads for low thermal resistance. The layout
recommendations for low EMI operation and maximum
thermal performance are available in the data sheet sec-
tion Low EMI PCB Layout.
Design files for this circuit board are available.
Specifications are at TA= 25°C
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
VIN/VIN EMI DC2629A Input Voltage Range 2.25 5.5 V
VOUT DC2629A VOUT Voltage Range 1.183 1.2 1.217 V
IOUT DC2629A Output Current 10 A
fSW Switching Frequency 1.8 2.2 MHz
EFF Efficiency VIN = 3.3V, IOUT = 5A 91 %

2
DEMO MANUAL DC2629A
Rev. 0
BOARD PHOTO
1.2V 10A Step-Down Converter
VIN
2.25V
TO 5.5V 22μF 1M
249k 100k
VIN
0.033μF
10k
220pF
L = XEL4030-101ME, COILCRAFT
VIN RT
AGND
FB
SW
PGOOD
VIN
EN
MODE/SYNC
SSTT
ITH
LTC3310S
PGND
100nH
0.22μF 22μF
15pF 140k
100k
22μF
x3
VOUT
1.2V
10A
0.22μF
DC2629A TA01a
LOAD CURRENT (A)
0
EFFICIENCY (%)
100
10
90
70
50
30
80
60
40
POWER LOSS (W)
20
05 93 7
DC2629 TA01b
104 82 61
VIN = 3.3V
VOUT = 1.2V
fOSC = 2MHz
3.0
0.3
2.7
2.1
1.5
0.9
2.4
1.8
1.2
0.6
0
POWER LOSS
EFFICIENCY
Efficiency vs Load Current

3
DEMO MANUAL DC2629A
Rev. 0
EMI TEST RESULTS
FREQUENCY (MHz)
AMPLITUDE (dBµV/m)
60
50
30
10
40
20
0
–10
–20
DC2629A G01
0 50 9030 70 11010040 8020 6010
PEAK LIMIT
PEAK
DC2629A DEMO BOARD
(WITH VOLTAGE APPLIED TO VIN EMI INPUT)
3.3V INPUT TO 1.2V OUTPUT AT 7.5A, fSW = 2MHz
FREQUENCY (MHz)
AMPLITUDE (dBµV/m)
50
5
45
35
25
15
40
30
20
10
0
DC2629A G02
0 500 900300 700 1000400 800200 600100
HORIZONTAL POLARIZATION
PEAK DETECTOR
PEAK LIMIT
PEAK
DC2629A DEMO BOARD
(WITH VOLTAGE APPLIED TO VIN EMI INPUT)
3.3V INPUT TO 1.2V OUTPUT AT 7.5A, fSW = 2MHz
FREQUENCY (MHz)
AMPLITUDE (dBµV/m)
50
5
45
35
25
15
40
30
20
10
0
DC2629A G03
0 500 900300 700 1000400 800200 600100
VERTICAL POLARIZATION
PEAK DETECTOR
PEAK LIMIT
PEAK
DC2629A DEMO BOARD
(WITH VOLTAGE APPLIED TO VIN EMI INPUT)
3.3V INPUT TO 1.2V OUTPUT AT 7.5A, fSW = 2MHz
CISPR25 Conducted EMI Emmisions with Class 5 Peak
Limits (Voltage Method)
Radiated EMI Performance (CISPR25 Radiated
Emmisions Test with Class 5 Peak Limits)
Radiated EMI Performance (CISPR25 Radiated
Emmisions Test with Class 5 Peak Limits)

4
DEMO MANUAL DC2629A
Rev. 0
QUICK START PROCEDURE
Demonstration circuit 2629A is easy to set up and evalu-
ate the performance of the LTC3310S. Refer to Figure1
for proper measurement equipment setup and follow the
procedure below:
NOTE:For accurate V
IN
, V
OUT
and efficiency measure-
ments, measure VIN at the VIN SNSE and GND SNSE tur-
rets and V
OUT
at the V
OUT
SNSE and GND SNSE turrets as
illustrated as VM1 and VM2 in Figure1. When measuring
the input or output voltage ripple, care must be taken
to avoid a long ground lead on the oscilloscope probe.
Measure the output voltage ripple by touching the probe
tip directly across the output turrets or to TP1 as shown
in Figure2.
1. Set the JP1 Jumper to the HI position.
2. With power off, connect the input power supply to VIN
and GND. If the input EMI filter is desired, connect the
input power supply to VIN EMI and GND.
3. Slowly increase PS1 to 1.0V. If AM1 reads less than
20mA,increasePS1 to 3.3V. VerifythatVM1reads3.3V
and VM2 reads 1.2V. Record VM1, VM2, VM3 AM1
and AM2. Connect an oscilloscope voltage probe as
shown in Figure2. Set Channel to AC coupled, voltage
scale to 20mV and time base to 10µs. Record VOUT
ripple voltage. Verify that PGOOD voltage is above 3V.
Calculate Die temperature using formula below:
TJ(°C)=
V
SSTT
4mV
−237
(1)
4. Increase the load by 1A intervals up to 10A and observe
the voltage output regulation, ripple voltage, and the
voltage on the SSTT turret.
5. If Pulse Skip Mode is desired, set PS1 to 0V. Install
a0Ω resistor in the R6 location or short the MODE/
SYNC turret to GND. Repeat steps 1 through 4. In step
4observethattheswitchingwaveformisnowoperating
in Pulse Skip Mode at low currents.
6. To change the frequency, remove R4 and R6 if installed.
Install the desired RT resistor in the R7 location. Note,
the MODE/SYNC pin is an output when R4 is installed
and the MODE/SYNC pin should have high impedance
toGNDandVIN.Sizetheinductor,outputcapacitors and
compensationcomponentstoprovidethedesired induc-
tor ripple and a stable output. Refer to the LTC3310S
datasheet and LTPowerCAD for more information on
choosing the required components.
7. To test the transient response with a base load, add the
desired resistor to produce a minimum load between
VOUT and I_STEP turrets (RL shown on Figure 1).
Note that the total load resistance will be RL plus R14
(100mΩ). Adjust a signal generator with a10ms pe-
riod, 10% duty cycle and an amplitude from 1V to 2V
to start.
8. Measure the I_STEP voltage to observe the current,
VI_STEP/100mΩ. Adjust the amplitude of the pulse
to provide the desired transient. Adjust the rising and
falling edge of the pulse to provide the desired ramp
rate. Figure3 shows a load step from 2A(RL = 0.51Ω)
to 8A. Refer to the following equations:
IOUT =
V
I_STEP
100mΩ
(2)
V
GS =
V
SG_INPUT −
V
I_STEP
(3)
9. When done, turn off SG1, PS1 and Load. Remove all
connections to demo board.
273

5
DEMO MANUAL DC2629A
Rev. 0
Figure1. Test setup for the DC2629A Demo Board
Figure2. Technique for Measuring Output Ripple and Step Response
QUICK START PROCEDURE

6
DEMO MANUAL DC2629A
Rev. 0
QUICK START PROCEDURE
Figure3. Technique for Measuring Load Step Response
VSG_INPUT
2V/DIV
0V
VI_STEP
200mV/DIV
200mV
1.20V
VOUT
20mV/DIV
LTC3310S DC2629A TRANSIENT
VIN = 3.3V
VOUT = 1.2V
IOUT = 2A TO 8A
20μs/DIV

7
DEMO MANUAL DC2629A
Rev. 0
THEORY OF OPERATION
Introduction to the DC2629A
The DC2629A demonstration circuit features the
LTC3310S, a Low Voltage Synchronous Step-Down Silent
Switcher. The LTC3310S is a monolithic, constant fre-
quency, current mode step-down DC/DC converter. An
oscillator, with frequency set using a resistor on the RT
pin, turns on the internal top power switch at the begin-
ning of each clock cycle. Current in the inductor then
increases until the top switch comparator trips and turns
off the top power switch. The peak inductor current, at
which the top switch turns off, is controlled by the volt-
age on the internal ITH node. The error amplifier servos
the ITH node by comparing the voltage on the VFB pin
with an internal 500mV reference. When the load cur-
rent increases, it causes a reduction in the feedback volt-
age relative to the reference leading the error amplifier to
raise the ITH voltage until the average inductor current
matches the new load current. When the top switch turns
off, the synchronous power switch turns on until the next
clock cycle begins or the inductor current falls to zero. If
overload conditions result in excessive current flowing
through the bottom switch, the next clock cycle will be
delayed until the switch current returns to a safe level.
If the EN pin is low, the LT3310S is in shutdown and in a
low quiescent current state. When the EN pin is above its
threshold, the switching regulator will be enabled.
The MODE/SYNC pin synchronizes the switching fre-
quency to an external clock, is a clock output or sets the
PWM mode. The PWM modes of operation are either pulse
skip or forced continuous. See the LTC3310S datasheet
for more detailed information.
The maximum allowable operating frequency is influenced
by the minimum on time of the top switch, the ratio of
VOUT to VIN and the available inductor values. The maxi-
mum allowable operating frequency may be calculated in
the formula below.
fSW(MAX) =
V
OUT
VIN(MAX) •TON(MIN)
(4)
Select an operating switching frequency below fSW(MAX).
Typically, it is desired to obtain an inductor current of 30%
of the maximum LTC3310S operating load, 10A. Use the
formulas below to calculate the inductor value to obtain
a 30% (3A) inductor ripple for the operating frequency.
L≥VOUT
3A •fSW
•1−VOUT
VIN(MAX)
⎛
⎝
⎜
⎜
⎞
⎠
⎟
⎟for VOUT
VIN(MAX)
≤0.5
(5)
L≥0.25•VIN(MAX)
3A •fSW
for VOUT
VIN(MAX)
>0.5
(6)
When determining the compensation components, C4,
C10, C11 and R12, controlling the loop stability and
transient response are the two main considerations. The
LTC3310S has been designed to operate at a high band-
width for fast transient response capabilities. This reduces
output capacitance required to meet the desired transient
voltage range. The mid-band gain of the loop increases
with R12 and the bandwidth of the loop increases with
decreasing C11. C4 along with R4 provides a phase lead
which will improve the phase margin. C10 along with
R12 provides a high frequency pole to reduce the high
frequency gain.
Loop stability is generally measured using the Bode Plot
method of plotting loop gain in dB and phase shift in
degrees. The 0dB crossover frequency should be less
the 1/6 of the operating frequency to reduce the effects
of added phase shift of the modulator. The control loop
phase margin goal should be 45º or greater and a gain
margin goal of 8dB or greater.

8
DEMO MANUAL DC2629A
Rev. 0
SCHEMATIC DIAGRAM
5
5
4
4
3
3
2
2
1
1
D D C C B B A A
HI LO
1.2V 10A
2.25V - 5.5V
EN
VOUT
MODE/SYNC
GND
EN
SSTT
PGOOD
GND
VIN
GND
VIN
GND
VOUT
GND
VOUT
SNSE
GND
SNSE
VIN
SNSE
GND
SNSE
OPT
REVISION HISTORY
ECO REV DESCRIPTION APPROVED DATE
-PRODUCTION MM 10-09-18
5
PCA ADDITIONAL PARTS
PULSE SKIP/SYNC
FORCED CONT
(VIN MAX)
MODE
PULSE SKIP
FORCED CONT.
R3 R4 R7
OPEN 0 or OPEN * POPULATED OR OPEN **
100k OPEN
* IF R7 IS POPULATED R4 MUST BE OPEN. ** MODE/SYNC PIN IS CLOCK OUTPUT WHEN R7 IS POPULATED.
0
FSW = 2MHz
CONNECT BY VOUT
SENSE ONLY
VIN EMI
VIN EMI
R6
OPEN
100k
2.25V - 5.5V
NOTES: UNLESS OTHERWISE SPECIFIED 1. RESISTORS: OHMS, 0402, 1%, 1/16W 2. CAPACITORS: 0402
SG_INPUT
I_STEP
OPTIONAL TRANSIENT RESPONSE CIRCUIT
VIN
VIN
VIN
VIN
GND_A
VIN
GND
GND_A
DATE:
IC NO.
SHEET OF
TITLE: DEMO CIRCUIT SCHEMATIC,
APPROVALS
PCB DES. APP ENG.
CUSTOMER NOTICE
LINEAR TECHNOLOGY HAS MADE A BEST EFFORT TO DESIGN A CIRCUIT THAT MEETS CUSTOMER-SUPPLIED SPECIFICATIONS; HOWEVER, IT REMAINS THE CUSTOMER'S RESPONSIBILITY TO VERIFY PROPER AND RELIABLE OPERATION IN THE ACTUAL APPLICATION. COMPONENT SUBSTITUTION AND PRINTED CIRCUIT BOARD LAYOUT MAY SIGNIFICANTLY AFFECT CIRCUIT PERFORMANCE OR RELIABILITY. CONTACT LINEAR TECHNOLOGY APPLICATIONS ENGINEERING FOR ASSISTANCE. THIS CIRCUIT IS PROPRIETARY TO LINEAR TECHNOLOGY AND SUPPLIED FOR USE WITH LINEAR TECHNOLOGY PARTS.
SCALE = NONE
SIZE:
SKU NO.
SCHEMATIC NO. AND REVISION:
PCA ASS'Y DWG:
www.analog.com
11
N. CARLONE
M.MERCHANT
LTC3310S
DC2629A 710-DC2629A_REV05
705-DC2629A_REV05
Wednesday, October 10, 2018
5V, 10A SYNCHRONOUS STEP-DOWN SILENT SWITCHER 2
DATE:
IC NO.
SHEET OF
TITLE: DEMO CIRCUIT SCHEMATIC,
APPROVALS
PCB DES. APP ENG.
CUSTOMER NOTICE
LINEAR TECHNOLOGY HAS MADE A BEST EFFORT TO DESIGN A CIRCUIT THAT MEETS CUSTOMER-SUPPLIED SPECIFICATIONS; HOWEVER, IT REMAINS THE CUSTOMER'S RESPONSIBILITY TO VERIFY PROPER AND RELIABLE OPERATION IN THE ACTUAL APPLICATION. COMPONENT SUBSTITUTION AND PRINTED CIRCUIT BOARD LAYOUT MAY SIGNIFICANTLY AFFECT CIRCUIT PERFORMANCE OR RELIABILITY. CONTACT LINEAR TECHNOLOGY APPLICATIONS ENGINEERING FOR ASSISTANCE. THIS CIRCUIT IS PROPRIETARY TO LINEAR TECHNOLOGY AND SUPPLIED FOR USE WITH LINEAR TECHNOLOGY PARTS.
SCALE = NONE
SIZE:
SKU NO.
SCHEMATIC NO. AND REVISION:
PCA ASS'Y DWG:
www.analog.com
11
N. CARLONE
M.MERCHANT
LTC3310S
DC2629A 710-DC2629A_REV05
705-DC2629A_REV05
Wednesday, October 10, 2018
5V, 10A SYNCHRONOUS STEP-DOWN SILENT SWITCHER 2
DATE:
IC NO.
SHEET OF
TITLE: DEMO CIRCUIT SCHEMATIC,
APPROVALS
PCB DES. APP ENG.
CUSTOMER NOTICE
LINEAR TECHNOLOGY HAS MADE A BEST EFFORT TO DESIGN A CIRCUIT THAT MEETS CUSTOMER-SUPPLIED SPECIFICATIONS; HOWEVER, IT REMAINS THE CUSTOMER'S RESPONSIBILITY TO VERIFY PROPER AND RELIABLE OPERATION IN THE ACTUAL APPLICATION. COMPONENT SUBSTITUTION AND PRINTED CIRCUIT BOARD LAYOUT MAY SIGNIFICANTLY AFFECT CIRCUIT PERFORMANCE OR RELIABILITY. CONTACT LINEAR TECHNOLOGY APPLICATIONS ENGINEERING FOR ASSISTANCE. THIS CIRCUIT IS PROPRIETARY TO LINEAR TECHNOLOGY AND SUPPLIED FOR USE WITH LINEAR TECHNOLOGY PARTS.
SCALE = NONE
SIZE:
SKU NO.
SCHEMATIC NO. AND REVISION:
PCA ASS'Y DWG:
www.analog.com
11
N. CARLONE
M.MERCHANT
LTC3310S
DC2629A 710-DC2629A_REV05
705-DC2629A_REV05
Wednesday, October 10, 2018
5V, 10A SYNCHRONOUS STEP-DOWN SILENT SWITCHER 2
E19
TP2
JP1
E15
R3
100k
C5 22uF 0805
E13
E5
U1
LTC3310S-LQFN
EN
1
SW 6
VFB 18
ITH
17
MODE/SYNC
13
RT 15
PGOOD 14
SSTT
16
VIN
3
PGND
5
AGND
2
VIN
11
VIN
12
VIN
4SW 7
SW 8 SW 9
PGND
19
PGND
10
C10
OPT
C11
220pF
PCB1 PCB, DC2629A REV05
MP1 STANDOFF,NYLON,SNAP-ON,0.50"
C17
10uF 0603
E9 TPB1
C4 15pF
MP4 STANDOFF,NYLON,SNAP-ON,0.50"
C14
10uF 0603
C12
OPT
STNCL1 TOOL, STENCIL, 700-DC2629A REV05
R2 249k
E7
E12
E20
E11
C3
22uF 0805
R8 20
C9
0.033uF
E2
Q1
SUD50N04-8M8P
2
1
3
R11
100k
5%
C20
0.22uF
C2
22uF 0805
R15
10k 5%
TP3 TP1
MP3 STANDOFF,NYLON,SNAP-ON,0.50"
R4
0
E10
R9 140k
E17
R6
OPT
L1
0.10uH
XEL4030-101MEC
L1_1
R12
10k
E18
C8
22uF
0805
+
C18 470uF
6TPE470MI
E14
LB1 LABEL
L2
100 OHMS @ 100MHz
C13
10uF 0603
E4 E6
R14 0.1
2818 10W
E1
TPA1
R13
0
R1
1M
+
C1
470uF
6TPE470MI
C6
22uF 0805
MP2 STANDOFF,NYLON,SNAP-ON,0.50"
E3
C16 10uF 0603
C7
0.1uF
R5
OPT
C15
0.1uF
E21
C19
0.22uF
E8
R10 100k
E16
R7
OPT
VOUT
VFB
RT
VFBRT
SW VOUT
MODE
SW
MODE
VOUT VIN

9
DEMO MANUAL DC2629A
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog
Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications
subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
PARTS LIST
ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER
Required Circuit Components
1 4 C2, C3, C5, C6 CAP., 22uF, X5R, 25V, 20%, 0805 SAMSUNG, CL21A226MAQNNNE
2 1 C4 CAP., 15pF, C0G, 50V, 5%, 0402 KEMET, C0402C150J5GAC7867
3 1 C9 CAP., 0.033uF, X7R, 25V, 10%, 0402 KEMET, C0402C333K3RACTU
4 1 C11 CAP., 220pF, X7R, 50V, 10%, 0402 YAGEO, CC0402KRX7R9BB221
5 2 C13, C14 CAP., 10uF, X5R, 10V, 20%, 0603 AVX, 0603ZD106MAT2A
6 1 L1 IND., 0.10uH 20% SHEILDED POWER INDUCTOR COILCRAFT, XEL4030-101MEC
7 1 R9 RES., 140k OHMS, 1%, 1/16W, 0402, AEC-Q200 VISHAY, CRCW0402140KFKED
8 1 R10 RES., 100k OHMS, 1%, 1/16W, 0402, AEC-Q200 VISHAY, CRCW0402100KFKED
9 1 R12 RES., 10k OHMS, 1%, 1/10W, 0402, AEC-Q200 PANASONIC, ERJ2RKF1002X
10 1 U1 IC, Low Voltage Syn. Stepdown Reg., LQFN-18 ANALOG DEVICES, LTC3310SEV#PBF
Additional Demo Board Circuit Components
1 2 C1, C18 CAP., 470uF, TANT. POSCAP, 6.3V, 20%, 7343,
18mOHMS, TPE
PANASONIC, 6TPE470MI
2 2 C7, C15 CAP., 0.1uF, X5R, 25V, 10%, 0402 AVX, 04023D104KAT2A
3 1 C8 CAP., 22uF, X5R, 25V, 20%, 0805 SAMSUNG, CL21A226MAQNNNE
4 2 C16, C17 CAP., 10uF, X5R, 10V, 20%, 0603 AVX, 0603ZD106MAT2A
5 2 C19, C20 CAP., 0.22uF, X7R, 16V, 10%, 0402, AEC-Q200 MURATA, GCM155R71C224KE02D
6 1 L2 IND., 100 OHMS @ 100MHz, FERRITE BEAD, 25%,
8A, 6mOHMS, 1812
WURTH ELEKTRONIK, 74279226101
7 1 Q1 XSTR., MOSFET, N-CH, 40V, TO-252 (DPAK) VISHAY, SUD50N04-8M8P-4GE3
8 1 R1 RES., 1M OHMS, 1%, 1/16W, 0402, AEC-Q200 VISHAY, CRCW04021M00FKED
9 1 R2 RES., 249k OHMS, 1%, 1/16W, 0402 VISHAY, CRCW0402249KFKED
10 2 R3, R11 RES., 100k OHMS, 5%, 1/16W, 0402, AEC-Q200 VISHAY, CRCW0402100KJNED
11 2 R4, R13 RES., 0 OHM, 1/16W, 0402, AEC-Q200 VISHAY, CRCW04020000Z0ED
12 1 R8 RES., 20 OHMS, 1%, 1/16W, 0402, AEC-Q200 VISHAY, CRCW040220R0FKED
13 1 R14 RES 0.1 OHM 1% 10W 2818 VISHAY DALE, WSHP2818R1000FEA
14 1 R15 RES., 10k OHMS, 5%, 1/16W, 0402, AEC-Q200 VISHAY, CRCW040210K0JNED
Hardware: For Demo Board Only
1 10 E1-E3, E5, E12, E14-E17, E20 TEST POINT, TURRET, 0.064", MTG. HOLE MILL-MAX, 2308-2-00-80-00-00-07-0
2 6 E4, E7, E10, E13, E18, E21 TEST POINT, TURRET, 0.094", MTG. HOLE MILL-MAX, 2501-2-00-80-00-00-07-0
3 5 E6, E8, E9, E11, E19 CONN., BANANA JACK, FEMALE, THT, NON-
INSULATED, SWAGE
KEYSTONE, 575-4
4 1 JP1 CONN., HDR, MALE, 1x3, 2mm, VERT, STR, THT WURTH ELEKTRONIK, 62000311121
5 4 MP1-MP4 STANDOFF, NYLON, SNAP-ON, 0.50" KEYSTONE, 8833
6 1 XJP1 CONN., SHUNT, FEMALE, 2 POS, 2mm WURTH ELEKTRONIK, 60800213421

10
DEMO MANUAL DC2629A
Rev. 0
 ANALOG DEVICES, INC. 2019
03/19
www.analog.com
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and
conditions set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation
Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”)
and Analog Devices, Inc. (“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to
Customer a free, limited, personal, temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and
agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted
is expressly made subject to the following additional limitations:Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board;and (ii) permit any Third
Party to access the Evaluation Board. As used herein, the term “Third Party”includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is
NOT sold to Customer;all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all
be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of
use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile
or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited
to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS
Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF
LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS”AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY
DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS
LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING
BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE
HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States
federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts
(excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits
to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.