Analog Devices EVAL-AD2437B1MZ User manual

EVAL-AD2437B1MZ Manual
Revision 2.1 , August 2023
Part Number
EVAL-AD2437B1MZ
Analog Devices, Inc.
One Technology Way
Norwood, MA 02062-9106

Copyright Information
© 2023 Analog Devices, Inc., ALL RIGHTS RESERVED. This document may not be reproduced in any form
without prior, express written consent from Analog Devices, Inc.
Disclaimer
Analog Devices, Inc. reserves the right to change this product without prior notice. Information furnished by Ana-
log Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its
use; nor for any infringement of patents or other rights of third parties which may result from its use. No license is
granted by implication or otherwise under the patent rights of Analog Devices, Inc.
Trademark and Service Mark Notice
The Analog Devices logo, Blackfin, SHARC, A2B, SigmaDSP, SigmaStudio+, and EngineerZone are registered
trademarks of Analog Devices, Inc.
All other brand and product names are trademarks or service marks of their respective owners.
Regulatory Compliance
The EVAL-AD2437B1MZ evaluation board is designed to be used solely in a laboratory environment. The board is
not intended for use as a consumer-end product or as a portion of a consumer-end product. The board is an open
system design, which does not include a shielded enclosure and, therefore, may cause interference to other electrical
devices in close proximity. This board should not be used in or near any medical equipment or RF devices.
The EVAL-AD2437B1MZ evaluation board contains ESD (electrostatic discharge) sensitive devices. Electrostatic
charges readily accumulate on the human body and equipment and can discharge without detection. Permanent
damage may occur on devices subjected to high-energy discharges. Proper ESD precautions are recommended to
avoid performance degradation or loss of functionality. Store unused boards in the protective shipping package.
EVAL-AD2437B1MZ Manual ii

Contents
Preface
Purpose of This Manual.................................................................................................................................1–2
Manual Contents ........................................................................................................................................... 1–2
Technical Support.......................................................................................................................................... 1–3
Supported Integrated Circuit ......................................................................................................................... 1–3
Supported Tools............................................................................................................................................. 1–3
Product Information...................................................................................................................................... 1–3
Analog Devices Website.............................................................................................................................. 1–3
EngineerZone ............................................................................................................................................. 1–4
Using the Board
Product Overview .......................................................................................................................................... 2–1
Package Contents........................................................................................................................................... 2–2
Default Configuration ................................................................................................................................... 2–2
Reference Design Information .......................................................................................................................2–3
AD2437 - Audio Bus A2B Transceiver ........................................................................................................... 2–3
ADA4661 -18 V, Precision, 725 µA, 4 MHz, CMOS RRIO Operational Amplifier ...................................... 2–4
ADAU1701 SigmaDSP 28-/56-Bit Audio Processor with Two ADCs and Four DACs .................................. 2–4
ADP2360 - 50 mA, 60 V, High Efficiency Buck Regulator............................................................................ 2–5
BD28623MUV - Class D Speaker Amplifier ................................................................................................. 2–5
IM69D120 High Performance Digital MEMS Microphone .......................................................................... 2–5
LT3502/LT3502A - 1.1MHz/2.2MHz, 500mA Step-Down Regulators in 2mm × 2mm DFN and MS10 .... 2–5
M24512-RMN6TP - Automotive 512-Kbit Serial I2C EEPROM with 1MHz clock..................................... 2–6
Hardware Reference
Connectors .................................................................................................................................................... 3–1
Stereo Connectors( TP5-TP8 ).................................................................................................................. 3–2
Audio I2S Connector ( P1) ........................................................................................................................ 3–3
EVAL-AD2437B1MZ Manual iii

SigmaStudio+ ( P2) .................................................................................................................................... 3–3
Multipurpose pins( P5 ) ............................................................................................................................. 3–3
ADC Input Connector( P7 ) ...................................................................................................................... 3–3
DAC Output Connector( P20 ) ................................................................................................................. 3–3
A2B ( P27 and P21) .................................................................................................................................. 3–3
Jumpers ......................................................................................................................................................... 3–4
AD2437 SIO0 Routing ( P4) ..................................................................................................................... 3–4
AD2437 SIO1 Routing ( P23)................................................................................................................... 3–5
AD2437 BCLK Select ( P16)..................................................................................................................... 3–5
ADAU1701 I2C Bus Switch ( P18 and P22)......................................................................................... 3–5
LEDs ............................................................................................................................................................. 3–5
A2B Interrupt ( DS2).................................................................................................................................. 3–6
Power Status Indicator ( DS1, DS3, DS5) ................................................................................................. 3–6
I2C Bus Switch ( DS4) ............................................................................................................................... 3–7
BD28623MUV Error Status ( DS6) ........................................................................................................... 3–7
iv EVAL-AD2437B1MZ Manual

1 Preface
Thank you for purchasing the Analog Devices, Inc. EVAL-AD2437B1MZ evaluation board.
The EVAL-AD2437B1MZ is an evaluation board to evaluate various peripherals of AD2437 A2B (Audio Bus) trans-
ceiver. Refer datasheet/manual to get more details about AD2437.
The EVAL-AD2437B1MZ is configured to be a Bus-Powered Sub (BPS) node. The EVAL-AD2437B1MZ can be
connected to a Main Node, Local-Powered Sub (LPS) or a Bus-Powered Sub (BPS) Node. These evaluation boards
are intended to be used with the SigmaStudio+ graphical development tool.
Block Diagram of Evaluation Board:
Preface
EVAL-AD2437B1MZ Manual 1–1

A PC host controls the AD2437 A2B main transceiver I2C/SPI signals over the USB-to- I2C/SPI bridge, the US-
Bi(EVAL-ADUSB2EB). This allows the PC to directly discover and control an A2B network as well as to read back
registers and monitor performance.
The SigmaStudio+®graphical development tool is the programming, development, and tuning software for the Sig-
maDSP, A2B, and Sharc processors. Familiar audio processing blocks can be wired together as in a schematic, and
the compiler generates DSP-ready code and a control surface for setting and tuning parameters. This tool allows
engineers with no DSP code writing experience to easily implement a DSP into their design and yet is still powerful
enough to satisfy the demands of experienced DSP designers. SigmaStudio+ links with both Analog Devices evalua-
tion boards and production designs to provide full in-circuit real-time IC control.
SigmaStudio+ includes an extensive library of algorithms to perform audio processing such as filtering, mixing, and
dynamics processing, as well as basic low-level DSP functions and control blocks. Advanced record-side processing
algorithms such as Enhanced Stereo Capture and wind noise detection are included in the standard libraries. Plug-in
algorithms from Analog Devices and 3rd party partners can be added to SigmaStudio+'s drag-and-drop library.
Along with its graphical DSP signal flow development, SigmaStudio+ also includes other features to speed up the
design cycle from product concept to release. SigmaStudio+ includes tools for intuitively setting control registers,
calculating tables of filter coefficients, visualizing filter magnitude and phase responses, generating C header files,
and sequencing a series of controls to ease your transition from SigmaStudio+ to system implementation on your
microcontroller.
Purpose of This Manual
This manual provides instructions for installing the product hardware (board). This manual describes the operation
and configuration of board components and provides guidelines for running code on the board.
Manual Contents
The manual consists of:
•Using the board
Provides basic board information.
•Hardware Reference
Provides information about the hardware aspects of the board.
•Bill of Materials
A companion file in PDF format that lists all of the components used on the board is available on the website
at https://www.analog.com/en/design-center/evaluation-hardware-and-software/evaluation-boards-kits/EVAL-
AD2437B1MZ.html.
•Schematic
Purpose of This Manual
1–2 EVAL-AD2437B1MZ Manual

A companion file in PDF format documenting all of the circuits used on the board is available on the website
at https://www.analog.com/en/design-center/evaluation-hardware-and-software/evaluation-boards-kits/EVAL-
AD2437B1MZ.html.
Technical Support
You can reach Analog Devices technical support in one of the following ways:
•Post your questions in the A2B support community at EngineerZone®:
http://ez.analog.com/a2b/
•Submit your questions to technical support directly at:
http://www.analog.com/support
•E-mail your questions about A2B transceiver applications and SigmaStudio+ to:
[email protected]
•Contact your Analog Devices sales office or authorized distributor. Locate one at:
http://www.analog.com/adi-sales
Supported Integrated Circuit
This evaluation system supports the Analog Devices AD2437 IC.
Supported Tools
Information about SigmaStudio+ and the A2B software plug-in for the EVAL-AD2437B1MZ evaluation board is
available at: www.analog.com/SigmaStudio+.
Product Information
Information about the AD2437 product family is available at: www.analog.com/A2B
Analog Devices Website
The Analog Devices website, http://www.analog.com, provides information about a broad range of products - ana-
log integrated circuits, amplifiers, converters, transceivers, and digital signal processors.
Also note, MyAnalog.com is a free feature of the Analog Devices website that allows customization of a web page to
display only the latest information about products you are interested in. You can choose to receive weekly e-mail
notifications containing updates to the web pages that meet your interests, including documentation errata against
all manuals. MyAnalog.com provides access to books, application notes, data sheets, code examples, and more.
Technical Support
EVAL-AD2437B1MZ Manual 1–3

Visit MyAnalog.com to sign up. If you are a registered user, just log on. Your user name is your e-mail address.
EngineerZone
EngineerZone is a technical support forum from Analog Devices, Inc. It allows you direct access to ADI technical
support engineers. You can search FAQs and technical information to get quick answers to your embedded process-
ing and DSP design questions.
Use EngineerZone to connect with other DSP developers who face similar design challenges. You can also use this
open forum to share knowledge and collaborate with the ADI support team and your peers. Visit http://
ez.analog.com to sign up.
Product Information
1–4 EVAL-AD2437B1MZ Manual

2 Using the Board
This chapter provides information on the major components and peripherals on the board, along with instructions
for installing and setting up the emulation software.
Product Overview
The board features:
•Analog Devices AD2437 - Audio Bus Transceiver
•Analog Devices ADA4661 -18 V, Precision, 725 µA, 4 MHz, CMOS RRIO Operational Amplifier
•Analog Devices ADP2360 - 50 mA, 60 V, High Efficiency Buck Regulator
•Analog DevicesLT3502/LT3502A - 1.1MHz/2.2MHz, 500mA Step-Down Regulators in 2mm × 2mm DFN
and MS10
•Microchip Technology 25AA256 - 256K SPI Bus Serial EEPROM
•Infineon IM69D120 High Performance Digital MEMS Microphone
•Mouser M24512-RMN6TP - Automotive 512-Kbit Serial I2C EEPROM with 1MHz clock
•Audio
•Analog Devices ADAU1701 SigmaDSP 28-/56-Bit Audio Processor with Two ADCs and Four DACs
•BD28623MUV - Class D Speaker Amplifier
•Four Stereo MEMS Microphones
•EEPROM
•Three 3.5mm audio jacks, One input, Two output
•A2B
•Two RJ45 Shielded Terminals
•LEDs
•Six LEDs : 3.3V, 5V, Power, Error, IRQ, Bus Switch
Using the Board
EVAL-AD2437B1MZ Manual 2–1

Package Contents
Your EVAL-AD2437B1MZ package contains the following items.
•EVAL-AD2437B1MZ board
•1m RJ45 Cable
•A2B Software - Online Request Documention
Contact the vendor where you purchased your EVAL-AD2437B1MZ evaluation board or contact Analog Devices,
Inc. if any item is missing.
Default Configuration
The Default Hardware Setup figure shows the default settings for jumpers and switches and the location of the
jumpers, switches, connectors, and LEDs. Confirm that your board is in the default configuration before using the
board.
Default Config of Sub Node
Package Contents
2–2 EVAL-AD2437B1MZ Manual