Analog way QuickVu QVU150-3G User manual

QuickVu - Ref. QVU150-3G
QUICK START GUIDE
Thank you for choosing Analog Way and the QuickVu. By following these simple steps, you will be able to set
up and use your powerful Dual Scaler Hi-Resoluon Seamless Switcher based on Analog Way’s new Midra™
plaorm within minutes. Discover the QuickVu capabilies and intuive interface while conguring your rst
show and unleash your creavity for a new experience in show and event management.
• 1 x QuickVu (QVU150-3G)
• 1 x Power supply cord
• 1 x Ethernet cross cable (for device update)
• 1 x Remote Control Soware (RCS²)*
• 1 x Set of 6 audio 5-pin screw terminals
• 1 x Front Rack Ears (the parts are stowed in the packaging foam)
• 1 x User Manual (PDF)*
• 1 x Quick Start guide*
* User manual, quick start guide and the RCS² are available on www.analogway.com
WHAT’S IN THE BOX
QUICK INSTALL AND SETUP

You may wish to reset the unit to factory sengs to get
started. Go to:       

1. Select the Output resoluon that matches the nave
resoluon of your display. You will next be prompted to
choose enable follow mode if desired and output rate.


 Inputs can be congured automacally using the Auto
Set All funcon. 
It will scan each input and detect the sync type that is
plugged in. You can sll do an Autoset or manual setup per
input.
The QuickVu has 2 layers available called:   and
QUICK FRAME.
3. To display a source, select a source (it will blink). Press
TAKE to transion your source from Preview to Program
output.
To view on Preview or change the contents of a dierent
source, simply select it. Only 1 layer can be seen on the
Preview.
4. To clear the layer select BLACK. Press TAKE to remove
the layer from the Program output.
 If you would like the Program and Preview to toggle/
ipop during each Take, enable this feature by going to
.
Once enabled, the old Program output will become the
new Preview aer each Take.
5. See the next page which describes the buon lighng
color code and other front panel features.

- sources seamlessly switched in the .

          

CAUTION!
If required, front handles of the
device can be dismantled, but
with cauon. The original screws
removed must not be reintro-
duced to their locaon without
handles in place. Substanal da-
mages can occur, including risk of
electric shock from the mains vol-
tage. Only M4x12mm screws can
be used. (They are supplied with
the unit.)



Menu scroll
knob


inputs #1 to #4
 inputs #1 to #2

inputs #1 to #2
 for inputs (balanced) #1 to #4
 for outputs (balanced) #1 to #2
 outputs #1 to #2
  access source 1 to 4, access HDMI 1 or HDMI 2  access SDI 1 to SDI 2

4-line VFD

 Hold
for 3 seconds for
stand-by mode
Ethernet
Plug

HDMI inputs #3 to #6.
Digital audio compliant

 Home menu
or back one level
validate the menu
or command

100-240 VAC 2.5A 50/60HZ /
FUSE F4A 250 VAC; internal,
autoswitchable; 110W
 communicaon port with a DB9 female connector
 DVI-D inputs #1 to #4. Capability to receive digital audio signal from HDMI connector via an adaptator (HDMI-compable)
  clear the output freeze the input linked to the current layer on Program
  outputs #1 to #2
 DVI-I outputs #1 to #2. Capability to transmit digital audio signal towards a HDMI connector via an adaptator (HDMI-compable)
 Transion the pre-selected sources onto the Program output with the selected eects

 shortcut to transion menu
 recall a custom stored preset
 The user should avoid disconnecng the power source (AC input) unl the unit is in stand-by mode.
 allows to quickly display a foreground Frame
 1 x BNC-F: 3G/HD/SD-SDI (with audio embedded)

OPERATION OVERVIEW
WORKING WITH THE QUICKVU
FRONT PANEL MENU 
 select to set the output types and resoluons of Output #1  select to set the output types and resoluons of Output #2  select to congure the 8 individual input types and resoluons  select to store and use presets  select to change source image sengs of an input  select to access keying and tling controls and parameters when video
layer is selected
 setup your background color and your Quick Frame  select to adjust layer size, posion, border, transparency or transions  select to store (record), use and manage logos and frames into the QuickVu select to access all audio input and output parameters  select to access device soware informaon, LAN sengs, reset factory set-
ngs, amongst other user oriented funcons (see next page)
 Inputs #1 to #4 : balanced & unbalanced connecon
Inputs #1 & #2: DVI embedded audio HDMI Inputs #3 & #4: DVI and HDMI embedded audio HDMI Inputs SPDIF #1 and #2: digital audio inputs Inputs HDMI #1 and #2: embedded audio HDMI Inputs SDI #1 to #2: embedded audio SDI Outputs #1 and #2: balanced & unbalanced connecon Outputs SPDIF #1 and #2: digital audio outputs Output SDI: embedded SDI audio output
1- Select an input. On the preview screen, the input
appears in the layer rectangle
 Select a transion (open/close) or an eect into Layer
menu [Home menu]
3- Press TAKE to view the result on the main screen 4- To remove layer, press BLACK  TAKE 5- For another layer setup, repeat from step #1
1- Press the  buon from the Home menu (all
funcons must be conrmed by the ENTER buon)
 Select  3- Select and then 4- On Format line, select the display’s nave resoluon 5- Control or adjust your display device (Monitor or Video
Projector)
 If necessary, select  in the Output menu
1- Press the  buon from the Home menu (all funcons must be conrmed by the Enter buon)  Press and  3- If the acquision is successful the source appears on Preview. 4- If the acquision has failed, check all connecons and perform
a manual setup
5- For a comprehensive Input Setup, please refer to user’s
Manual
 For a manual input setup, press the  buon:
a) Press , b) Select the right input from Input #1 up to SDI #2, then c) Select , d) Select  and choose the input type.
BUTTON COLOR USAGE
OUTPUT SETUP INPUT SETUP

#1 = Source is on the Program output #2 = Freeze enable




#1 = Source is on Preview #2 = Funcon available for modicaon
Contextual buon
Layer/source selected or is currently acve on the Program output
Layer/source selected or is not currently
acve on the Program output
To adjust layer Size or Pos, use the Layer Menus. To adjust Blanking, use the Auto Centering or Blanking adjustments in the Image menu.
L+
L-
R+
R-
UNBALANCED
Left
Right
GROUND
GROUND GROUND
L+
L-
R+
R-
BALANCED
L+ R+ L- R-
GROUND(S)

06/02/2014 - QVU150-3G-QSG
Code: 140162
For complete details and operaons procedures, please refer to the QuickVu User’s Manual and our website for further informa-
on: 
This Analog Way product has a 3 year warranty on parts and labor, back to factory. This warranty does not include faults resulng
from user negligence, special modicaons, electrical surges, abuse (drop/crush), and/or other unusual damage. In the unlikely
event of a malfuncon, please contact your local Analog Way oce for service.
The HDCP Encrypon can be disabled on HDMI/DVI inputs or/and Program Output #1 / Program Output #2. This can be useful
when you have a computer which is detecng the HDCP compliance of your switcher and protecng the content by encrypng the
signal from this computer. This feature will disable the HDCP compliance on this specic HDMI/DVI input only.
If you want to use HDCP content from your sources, be sure to use only HDCP compliant screens or projector. If it’s not the case,
the output image could be disabled.
Screen will go to black without displaying the HDCP input image, or parally layer out on HDCP content.
The output status can provide you all informaon about the output in real me. This feature is parcularly useful when HDCP is
used with long cable to be sure the communicaon is well handled.
The Autotake funcon performs a TAKE automacally each me an input is selected.
AUTO-LOCK allows to select an input only if a signal is valid.
 full and individual frame that can be displayed on top of every layer.
It is possible to store up to 8 frames in the device non volale memory.
- Select RECORD FRAMES in the frames menu.
- A white rectangle will appear on your Program display, indicang the frame which will be caught and saved. (The Frame can be
captured in Preview too.)
- To select the Quick frame, please go into the SCREEN menu, select QUICK FRAME menu and then choose a Frame slot. The
selected frame will be your QUICK FRAME.
Now to display it, simply press the front panel buon QUICK FRAME. It becomes solid RED.
- To remove the QUICK FRAME, press the QUICK FRAME buon on the front panel. It becomes solid green.
 a long press on the BLACK buon will clear all layers on Preview. Press TAKE to view your Program display turn to black.
The [Empty] term appears next to all unused slots





GOING FURTHER WITH THE QUICKVU
HOME MENU
HOME MENU
HOME MENU
OUTPUT #1
HOME MENU
CONTROL

CONTROL

FUNCTIONS
RECORD FRAMES
FUNCTIONS
HDCP DETECTION
AUTOTAKE


DISABLED
AUTOMATIC
ENABLED OR DISABLED
ENABLED OR DISABLED
HOME MENU
INPUTS INPUT # HDMI OR DVI SETTINGS HDCP ENABLE ENABLED OR DISABLED


Tel.: [phone]
[e-mail]

Tel.: [phone]
[e-mail]

Tel.: [phone]
[e-mail]