Analog way Smart Quad SQD200 User manual

QUICK START GUIDE
What’s in the box
Quick install and setup
Thank you for choosing Analog Way and the Smart Quad. By following these simple steps, you should be able to setup
and use your powerful Hi-Resolution Mixer Switcher within minutes. Discover the Smart Quad extensive capabilities
and intuitive interface while conguring your rst show, and unleash your creativity for a new experience in show and
event management by Analog Way.
Smart Quad - Ref. SQD200
1 x Smart Quad (SQD200)
1 x AC Power cable
2 x DVI-I male to HD15 female and DVI-D female breakout cable
1 x HD15 to 5 BNC cable
1 x Ethernet cross cable (for device update)
1 x DB9 to 4 BNC cable + mini-Din 4
1 x Set of 3 audio 10-pin screw terminals
4 x M4x12mm screws
1 x RCS - Remote Control Software (PC only) *
1 x Quick Start guide (PDF version) *
1 x User Manual (PDF version) *
* Download on our website: www.analogway.com
Key points:
 
 
 
 
Getting started:
 


 

 
 
 

        

        

      


IMPORTANT:       
ENTER

WARNING !
If required, front handles of the device can be dismantled,
but with caution.
The original screws removed must not be reintroduced to
their location without handles in place.
Substantial damages can occur, including risk of elec-
tric shock from the mains voltage.
Only M4x12mm screws can be used.
(They are supplied with the unit)

Smart Quad - Ref. SQD200 Front Panel Description
EXIT/MENU: Home Menu or back one level ENTER: Validates the menu or command
#1 to #7: Press to access analog source #1 to #7 DVI 1 to DVI 2: Press to access DVI #1 or DVI #2 SDI 1 to SDI 2: Press to access SDI #1 or SDI #2 BLACK: Change the active layer to Black
Bkgnd Frame: Press to access Bkgnd Frame Layer LOGO: Press to access logo Layer EFFECT: Press to select a customized effect FREEZE: Freeze the input linked to the current layer on MAIN PRESET: Select a customized preset (4 memories available)
STAND-BY: Hold for 3 seconds for stand-by Mode
CONTROL
INPUT SELECTIONS FUNCTION CONTROL
STAND-BY
OUTPUT SETUP 1- Press the EXIT/MENU button from the Home menu
[all functions must be conrmed by the ENTER button]
2- Press [Output] 3- Press [Output format]
4- On Format line, select the display’s native resolution 5- Control or adjust your display device (Monitor or Video
Projector)
6- If necessary, select [Test Pattern] in the Output menu
INPUT SETUP 1- Press the EXIT/MENU button from the Home menu [all functions must be
conrmed by the Enter button]
2- Press [Input] and [Autoset ALL] 3- If the acquisition has failed, check all connections and perform a manual setup 4- For a comprehensive Input Setup, please refer to user’s Manual 5- For a manual input setup, press the EXIT/MENU button: a) Press [Input], b) Select the right input from Input #1 up to SDI #2, then c) Select [Type].
NOTE: To adjust input Size or Pos, use the [Layer] Menus.
To adjust Blanking, use the Auto-Centering or Blanking adjustments in the
Image menu.
Display the pre-selected sources onto the MAIN output with the selected effects
W1 to W4: Select the current Layer
TAKE
QUADRAVISION
BUTTON COLOR USAGE #1 = Source is on the main outputs Solid red: #2 = Freeze enable
#3 = Stand-by button #4 = Preset Selection Solid green: #1 = Source is on Preview
#2 = Function available for modication
Blinking red: Layer/source selected, and is currently active on the main output Blinking green: Layer/source selected, and is not currently
active one the main output

Smart Quad - Ref. SQD200 Rear Panel Description
RS-232 communication port on a DB9 female connector or TCP/IP on RJ45 connector
Power supply: IEC/EN/UL/CSA 60950-1, internal, autoswitchable
Universal Analog Computer/TV/HDTV inputs
3G/HD/SD-SDI inputs #1 & #2: female BNC
DVI inputs #1 & #2: female DVI-I
Outputs #1 & #2: female HD15, DVI-I
Prelist and Main Audio Output
IP-LAN connectors 3.5mm Jack Stereo
Connector input (unbalanced)
1 x BNC-F: 3G/HD/SD-SDI (with audio embedded) 1 x DB9-F: Analog & HDTV formats
MCO Male Connector for inputs (inputs #5 to #6) DVI #1 and DVI #2: Unbalanced Input 7 and AUX: Balanced
AUDIO INPUTS CONNECTIONSHOME MENU
- INPUT: select to congure the 1 individual input types and resolutions - MAIN OUT: in Mixer mode, select to set Format and Rate - PREVIEW OUT: in Mixer mode, select to Format and Rate
- PRESET: select to store and use presets - IMAGE: select to change source image settings of an input - KEYING/TITLING: select to access keying and titling controls and parameters - LAYER: select to adjust layer size, position, border transparency or transitions - LOGOS/FRAMES: select to store (record), use and manage logos and frames - AUDIO: select to access all audio input and output parameters - CONTROL: select to access device software information, LAN settings, reset factory
settings, amongst other user oriented functions (see next page)
- VIRTUAL T-Bar: select to access the Virtual T-Bar
WORKING WITH SQD200 The features of SQD200 can be controled by the external remote control as: - Orchestra - Ref. ORC50 - Axion2 - Ref. ARC200 - Remote Control Software - Ref. RCS (supplied) - Triple Remote Control Keypad - Ref. TRK-800 - Remote Control Keypad - Ref. RK-300
AUDIO OUTPUT
3.5mm Jack Stereo Connector Inputs #1 to #4: Unbalanced connection MCO Male Connectors Inputs #5 to #6: Unbalanced connection Inputs DVI #1 & #2: Unbalanced connection Main Output: Balanced connection
Input #7 (AUX): Balanced connection
4
L+
L-
R+
R-
BALANCED
L+ R+ L- R-
GROUND(S)
Right
Left
Ground
5 6
L
R
L
R
UNBALANCED
LEFT LEFT RIGHT RIGHT GROUND(S)
Input #5 Input #6

Going further with the Smart Quad
For complete details and operations procedures, please refer to the Smart Quad User’s Manual and our website for further
information : www.analogway.com
Version : 4.00 - 19/03/2012
Code : 140128
WORKING WITH TEMPLATES
Warranty
This Analog Way product has a 3 year warranty on parts and labor, back to factory. This warranty does not include faults
resulting from user negligence, special modications, electrical surges, abuse (drop/crush), and/or other unusual damage.
NOTE : The updater les are available on our web site: http://www.analogway.com
Some templates are available for the Quadravision Mode, you will nd them here:
Templates are just here to provide some useful layers positions, you can adjust them manually at any time.
Each template has to be saved in presets before doing any change. If it’s not the case, all template settings
will be deleted.
W 1
W 1
W 2
W 4
W 4
W 3
W 1 W 1
W 2
W 2
W 2
W 4
W 4
W 4
W 3
W 3
W 3
W 1
W 3
W 2
W 1
Win1 Full screen Win2 Full screen
Win3 Full screen Win4 Full screen
W 1
W 1
W 2
W 4
W 4
W 3
W 1 W 1
W 2
W 2
W 2
W 4
W 4
W 4
W 3
W 3
W 3
W 1
W 3
W 2
W 1
W 1
W 1
W 1
W 2
W 1
W 3
W 2
W 3
W 2
W 1
W 2
Split Screen
3 x Left + 1 x Right 1 x Top + 3 x Bottom
1 x Left + 3 x Right
Split 3V Split 3H
Split 2H Split 2V