Analytic Systems FCA250 User manual

Installation &
Operation Manual
FCA250 & FCA500
FREQUENCY CONVERTER
8128 River Way, Delta B.C. V4G 1K5 Canada T. 604.946.9981 F. 604.946.9983 TF. 1.800.668.3884 (US/CANADA)
www.analyticsystems.com

2
Copyright (2005-2013) Analytic Systems Ware (1993) Ltd.

3
IMPORTANT & SAFETY INSTRUCTIONS
1) SAVE THESE INSTRUCTIONS — is manual contains important safety and operating
instructions for the frequency converter.
2) Do not expose the frequency converter to rain or snow.
3) Use of an attachment not recommended or sold by the frequency converter manufacturer may
result in a risk of re, electric shock, or injury to persons.
4) Do not disassemble the frequency converter; take it to a qualied serviceman when service or
repair is required. Incorrect reassembly may result in a risk of electric shock or re.
5) To reduce risk of electric shock, unplug the frequency converter from all sources of power
before attempting any maintenance or cleaning. Turning o controls will not reduce this risk.
6) Never place the frequency converter directly above battery; gases from battery will corrode and
damage the transfer switch.
7) Never allow battery acid to drip on the frequency converter when reading gravity or lling
battery.
GROUNDING AND AC POWER CORD CONNECTION INSTRUCTIONS — e frequency converter
should be grounded to reduce risk of electric shock. e frequency converter is equipped with electric recep-
tacles capable of accepting an equipment-grounding conductor and a grounding plug.
Analytic Systems does not recommend the use of the FCA250 & FCA500 Frequency Converter in life sup-
port applications where failure or malfunction of this product can be reasonably expected to cause failure of
the life support device or to signicantly aect its safety or eectiveness. Analytic Systems does not recom-
mend the use of any of its products in direct patient care.
Examples of devices considered to be life support devices are neonatal oxygen analyzers, nerve stimulators
(whether used for anesthesia, pain relief, or other purposes), autotransfusion devices, blood pumps, debril-
lators, arrhythmia detectors and alarms, pacemakers, hemodialysis systems, peritoneal dialysis systems,
neonatal ventilator incubators, ventilators for both adults and infants, anesthesia ventilators, and infusion
pumps as well as any other devices designated as “critical” by the U.S. FDA.

4
Introduction
e FCA250 & FCA500 frequency converter series were designed electrically and mechanically to achieve
optimal ruggedness required for industrial, telecommunications, military and airborne applications.
Electrical Connections
e input can be grounded either on the positive or negative, or may be le oating. e output is normally
grounded, although it can be oating if required.
e input connections are via a 3-pole terminal block. GND, PH and N are clearly labeled. e output con-
nections are via a standard North American receptacle (other input/output options available).
All connections should follow NEC standards.
Location
e unit should be mounted securely to a at surface with a minimum of one-inch clearance to provide
ample airow and to achieve maximum continuous power. Cooling is enhanced if the unit is installed on a
metal surface to allow for additional conduction cooling.
ON/OFF Switch
e FCA250 & FCA500 frequency converter series have an ON/OFF switch which disables the converter’s
control circuit. Turning the switch to the ‘OFF’ position cuts the power to the AC output. A minimum cur-
rent drain will continue on the input side.
Electronic Protection
e frequency converter has a number of protection circuits designed to provide full electronic protection:
Grounding – e input can be either positively or negatively grounded, or may be le oating. e output is
normally oating, although it can be grounded.
ermal shutdown – In the event of overheating due to high ambient temperatures, blocked airow or over-
load conditions, the internal thermal protection circuit will shut the unit down. Operation will automatically
resume when the temperature reaches the specied operating level.
Overload and short-circuit protection – In case of an overload or short circuit, the converter will go into
”hiccup” mode. is means that the unit will automatically shut down and will periodically test whether or
not the overload condition still exists.
Input and output ltering – All FCA250 & FCA500 series frequency converters have a double stage input
lter to restrict EMI emissions. Filtering also provides immunity against voltage spikes and other distur-
bances on the input power line. e converters meet FCC 20780 Class B and EN 55022 Class B conducted
emission requirements.
Operating
Before plugging any appliance into the frequency converter, please refer to its power requirements. Power re-
quirements are indicated in watts (W), volt-amps (VA) or amps (A). Ensure that the rating does not exceed
the frequency converter’s capacity.

5
FCA250
Specications
Safety Considerations
WARNING:
e FCA250 & FCA500 series frequency converters generate 115VAC (or 230VAC) power – the same voltage
coming out of a standard wall outlet. is voltage can be hazardous and has to be treated with the same cau-
tion as with a regular electrical outlet.
As with any other electrical equipment, the frequency converter must be protected from water and moisture
at all times.
INPUT
Input Voltage: 115/230 VAC +/- 20%, auto-ranging, 47 to 410Hz
Input Protection: Inrush current limiting & thermal fuse
Input Isolation: 2250 Vdc input to output, input to chassis & output to chassis
RFI Suppression: Meets requirements of FCC 20780 Class B and EN55022 Class B con-
ducted emissions as a minimum
OUTPUT
Output Voltage / Current:
115 VAC / 60 Hz / 2.1 Amp continuous (250 Watts)
230 VAC / 50 Hz / 1.05 Amp continuous or
any combination including frequency up to 400Hz
Wave Form: Sinusoidal
Total Harmonic Distortion: Better than 5% at full load
Line Regulation: Maximum 0.5%
Load Regulation: Maximum ± 6% from 10% load to full load
GENERAL
Temperature Dri: 0.05% per º C over operating temperature range
Operating Temp. Range: 0º C to +50º C for full specication (no fan)
Humidity: 5 - 95 % non-condensing
Output Protection: Current limiting with short-circuit protection. ermal shutdown with
automatic recovery in case of continuous overload or insucient airow
Output Overload Protection: Hiccup at 300 W
Output Over-voltage Protection: By internal supply voltage limiting at 120% V out, nominal level
Load Crest Factor: Maximum 2.5 at 90% load
Eciency: Minimum 78% at full load
Cooling: By convection / conduction
Input Connection: Screw-type terminal block
Output Connection: Standard AC Receptacle (North American Type)
Package Size / Weight: 5.0 x 5.3 x 15.5 Enclosed case, 9 pounds ( 4.1 kg )

6
FCA500
INPUT
Input Voltage: 115/230 VAC +/- 20%, auto-ranging, 47 to 410Hz
Input Protection: Inrush current limiting & thermal fuse
Input Isolation: 2250 Vdc input to output, input to chassis & output to chassis
RFI Suppression: Meets requirements of FCC 20780 Class B and EN55022 Class B con-
ducted emissions as a minimum
OUTPUT
Output Voltage / Current:
115 VAC / 60 Hz / 4.4 Amp continuous (500 Watts)
230 VAC / 50 Hz / 2.2 Amp continuous or
any combination including frequency up to 400Hz
Wave Form: Sinusoidal
Total Harmonic Distortion: Better than 5% at full load
Line Regulation: Maximum 0.5%
Load Regulation: Maximum ± 6% from 10% load to full load
GENERAL
Temperature Dri: 0.05% per º C over operating temperature range
Operating Temp. Range: 0º C to +50º C for full specication (no fan)
Humidity: 5 - 95 % non-condensing
Output Protection:
Current limiting with short-circuit protection. ermal shutdown
with automatic recovery in case of continuous overload or insucient
airow
Output Overload Protection: Hiccup at 600 W
Output Over-voltage Protection: By internal supply voltage limiting at 120% V out, nominal level
Load Crest Factor: Maximum 3.0 at 90% load
Eciency: Minimum 78% at full load
Cooling: By internal fan
Input Connection: Screw-type terminal block
Output Connection: Standard AC Receptacle (North American Type)
Package Size / Weight: 5.0 x 5.3 x 15.5 Enclosed case, 9 pounds ( 4.1 kg )
Designed and manufactured by: ANALYTIC SYSTEMS WARE (1993) LTD.
8128 River Way, Delta, B.C., V4G 1K5, Canada
phone [phone] fax [phone] toll free 800-668-3884 US/Canada
email: [e-mail] web site: www.analyticsystems.com Revised Mar 2004
* Specications subjects to change without notice.

7
Limited Warranty
1. e equipment manufactured for Analytic Systems Ware (1993) Ltd. (the “Warrantor”) is war-
ranted to be free from defects in workmanship and materials under normal use and service.
2. is warranty is in eect for: 2 Years from date of Purchase.
3. In case any part of the equipment proves to be defective, the Purchaser should do the following:
a. Prepare a written statement of the nature of the defect to the best of the Purchasers knowledge,
and include the date of purchase, the place of purchase, and the Purchasers name, address and
telephone number.
b. Call Analytic Systems at 800-668-3884 or 604-946-9981 and request a return material authori-
zation number (RMA).
c. Return the defective part or unit along with the statement at the Purchasers expense to the War-
rantor; Analytic Systems Ware (1993) Ltd., 8128 River Way, Delta, B.C., V4G1K5, Canada.
4. If upon the Warrantor’s examination the defect proves to be the result of defective material or
workmanship, the equipment will be repaired or replaced at the Warrantor’s option without
charge, and returned to the Purchaser at the Warrantor’s expense by the most economical means.
Requests for a dierent method of return or special handling will incur additional charges and are
the responsibility of the Purchaser.
5. Analytic Systems reserves the right to void the warranty if:
a. Identication marks or serial numbers are removed or altered in any way.
b. Our invoice is unpaid.
e defect is the result of misuse, neglect, improper installation, environmental conditions,
non-authorized repair, alteration or accident.
6. No refund of the purchase price will be granted to the Purchaser, unless the Warrantor is unable
to remedy the defect aer having a reasonable number of opportunities to do so.
7. Only the Warrantor shall perform warranty service. Any attempt to remedy the defect by anyone
else shall render this warranty void.
8. ere shall be no warranty for defects or damages caused by faulty installation or hook-up, abuse
or misuse of the equipment including exposure to excessive heat, salt or fresh water spray, or
water immersion except for equipment specically stated to be waterproof.
9. No other express warranty is hereby given and there are no warranties that extend beyond those
described herein. is warranty is expressly in lieu of any other expressed or implied warranties,
including any implied warranty of merchantability, tness for the ordinary purposes for which
such goods are used, or tness for a particular purpose, or any other obligations on the part of the
Warrantor or its employees and representatives.

10. ere shall be no responsibility or liability whatsoever on the part of the Warrantor or its em-
ployees and representatives for injury to any person or persons, or damage to property, or loss
of income or prot, or any other consequential or resulting damage which may be claimed to
have been incurred through the use or sale of the equipment, including any possible failure of
malfunction of the equipment, or part thereof.
11. e Warrantor assumes no liability for incidental or consequential damages of any kind.
8128 River Way, Delta B.C. V4G 1K5 Canada T. 604.946.9981 F. 604.946.9983 TF. 1.800.668.3884 (US/CANADA)
www.analyticsystems.com