Andersen LuminAire User manual

1
Emco Enterprises, Inc., is a wholly owned subsidiary of Andersen Corporation. Emco Enterprises, Inc.
manufactures and supports the limited warranties for Andersen®and EMCO®doors. “Andersen”,
“EMCO” and all other marks where denoted are trademarks of Andersen Corporation.
©2019 Andersen Corporation. All rights reserved.
Installation Guide
Please Do Not Return Product to Store!
with any questions regarding installation, lost part replacement, or anything else related to your retractable
insect screen purchase. Replacement parts can also be found at: parts.andersenstormdoors.com
Read this entire guide before you begin your installation. If your abilities do not
match the requirements of this installation, contact an experienced contractor.
PLEASE call the Storm Door Solution Center at 844-813-6664,
For installation help please visit www.AndersenLuminAire.com/install
Andersen SDD, PO Box 853
Des Moines, IA 50306-0853
05-2019 r2 Print in Color
p/n 900265
Replacement Passive Screen Housing for Andersen®
LuminAire®Retractable Insect Screen Double Door
DOUBLE DOOR PARTS OVERVIEW
2
4
1
3
Your replacement part should contain the following parts.
Passive Screen Housing
End Caps (attached to each end of housing)
Orange Installation Clips
Shipping Plastic Wrap
Not Shown: Screw Pack containing:
• 1 inch #8 screws (qty 6)
• ½ inch #8 self-tapping screws (qty 6)
• #2 Phillips Bit
• ⁄ inch Drill Bit
• ⁄ inch Hex Wrench
• Corner Pile (qty 2)
2
To avoid product damage, be sure to place all parts of your retractable
insect screen on a soft non-abrasive surface such as carpet, drop cloth
placed on your lawn or cardboard.
NOTICE
1
3
3
4
2
2

2
SAFETY FIRST: Please read and follow all Cautions and Warnings in this guide.
The retractable insect screen is intended for reasonable
insect control and not the retention of objects, persons,
or pets within the interior. The retractable insect screen
will not stop a person from falling through the door.
Follow manufacturers' instructions for hand and power
tools. Always wear safety glasses. Failure to do so could
result in injury, product or property damage.
Windows and doors can be heavy. Use safe lifting techniques and a reasonable number of people with enough
strength to lift, carry, and install window and door products. Heavier windows and doors will require mechanical
assistance. Failure to do so could result in injury, product or property damage.
Metal fasteners and components could corrode when exposed to preservative-treated or re-retardant treated
lumber. Use approved fasteners and components to fasten window or door. Failure to do so could cause a failure
resulting in injury, product or property damage.
Fastener must attach to a structural framing member with a 1" minimum fastener embedment. Failure to do so
could result in injury, product or property damage.
DO NOT remove screws that attached installation clips or gusset plates to window or door frames. Doing so could
result in injury, product or property damage.
Metal components of the retractable insect screen may
become hot when exposed to sunlight.
IMPORTANT
WARNING WARNING
WARNINGCAUTION
PRIMARY
ACTIVE
DOOR
PRIMARY
ACTIVE
DOOR
ACTIVE
HOUSING
ACTIVE
HOUSING
DOOR OPENING DOOR OPENING
PASSIVE
HOUSING
PASSIVE
HOUSING
a From the exterior of the screen assembly, take note of the screen assembly's orientation.
This is the orientation the screen assembly should be in when reinstalled.
a
OR
To avoid product damage. It is recommended
to use two (2) people to uninstall and reinstall
double door unit into the door opening.
NOTICE
1
REMOVAL #2 Phillips Bit
(provided)
Tools Recommended:
RECOMMENDED TOOLS
Drill
Safety Glasses
Sealant
Screwdrivers
!
!
1/2”
1/2”
1/2”
1”
1 1/2”
2”
1 1/2”
5/8”
5/8”
#2 Phillips Bit
(provided)
!
!
1/2”
1/2”
1/2”
1”
1 1/2”
2”
1 1/2”
5/8”
5/8”
Work Gloves
!
!
1/2”
1/2”
1/2”
1”
1 1/2”
2”
1 1/2”
5/8”
5/8”
!
!
1/2”
1/2”
1/2”
1”
1 1/2”
2”
1 1/2”
5/8”
5/8”
Major Injury / Death
Product or Property
Damage
Minor Injury
Procedure and Product
Information
This is the Safety Alert Symbol used to alert you to
potential injury hazards. Obey all safety messages that
follow this symbol to avoid possible injury or death.
WARNING
NOTICE
CAUTION
IMPORTANT
Signal Word and Consequence
COULD
Result in:
COULD
Result in:
COULD
Result in:
Soft Cloth
Scissors

3
1 REMOVAL - Continued
c From the interior extend the screen from the
Passive Housing so it is clear of your drill/
driver. Remove the three screws from the
Screw Flange. Dispose of screws properly.
b1 From the interior of the screen assembly, remove the six screws from the Sill Adapter. Dispose of screws properly.
b2 Rotate Sill Adapter up and pull out of Adapter Channel (see Figure 1 & 2)
b3 Save the Sill Adapter for reinstallation in future step.
d Extend the screen from the Active Housing
so it is clear of your drill/driver. Remove
the three screws from the Screw Flange,
supporting the screen assembly as needed.
Dispose of screws properly.
c
ACTIVE
HOUSING
PASSIVE
HOUSING
d
e Carefully tip and lift Screen Assembly out of
Door Opening and place it at with the interior
side facing up on a non-abrasive surface.
SCREEN
ASSEMBLY
DOOR
OPENING
e
b
SILL
ADAPTER
DOOR
SILL
SILL
ADAPTER
DOOR
SILL
ADAPTER
CHANNEL
SILL
ADAPTER
Figure 2
Figure 1
SCREW
FLANGE
SCREW
FLANGE
SCREWSCREW
C
PASSIVE
SCREEN
C
(Passive Screen)
C
C
g
PASSIVE HOUSING
END CAP C
LOCKING TAB
TRACK
EXTENDER C
For Some Installations Only:
If the track extender is present, it needs to be saved and reinstalled.
f1 Carefully slide the Passive Housing o of the Screen Tracks, both top
and bottom Endcaps C and A.Properly dispose of Passive Housing.
f2 Remove both Slot Covers from back of Passive Housing and set aside
to be reinstalled later. Properly dispose of Passive Housing.
g Check to see if Track Extenders are used. If present slide both
Track Extenders out of the endcaps and set aside to be reinstalled
in later step.
C
C
32
36
PASSIVE
SCREEN
ENDCAP C
fSCREEN
TRACK
PASSIVE
HOUSING
SLOT COVER

4
Track Extenders for Passive Housing
Not all openings require the use of Track Extenders. They are for reinforcing the
screen assembly at the wider ranges of the conguration.The track extenders can
not be used at narrower congurations as screen interference will occur. The chart
below details when and when not to use screen extenders.
Opening Width Configuration Track Extender
71" – 72" 72" Config. Yes - Needed
70" – 70 ⁄" 72" Config. Not needed
69" – 69 ⁄" 68" Config. Yes - Needed
Less than 69" 68" Config. Not needed
C
PASSIVE
SCREEN
C
(Passive Screen)
C
C
a
PASSIVE HOUSING
ENDCAP C
LOCKING TAB
TRACK
EXTENDER C
SCREEN TRACK SIDE C (PASSIVE)
For Some Installations Only:
If the track extender is present, it needs to be saved and reinstalled.
A
A
C
C
Track Extender A
REASSEMBLE
SCREEN
TRACKS &
PASSIVE
HOUSING
2
C
Passive
Screen
Passive Housing Screen Track Screen Track
KEY REFERENCES
Screw Flanges
Receiving Tabs
Letter Labels
Passive Label
1
2
3
4
1
433
3
2
a1 If your installation required the Track Extenders, position the thicker
end of the Track Extender C toward Passive Housing Endcap C with the
Locking Tab toward the Screen Track and slide into Endcap C.
a2 Repeat for Endcap A and Track Extender A at other end of housing.
a1 With the screen assembly laying at on a non-abrasive surface, with the side labeled Interior facing up, leave the screen in the retracted position.
a2 Slide the Receiving Tab on Endcap C inside the Screen Track. Make sure the Receiving Tab ts inside the Screen Track, and the Screen Track slides into the
Channel. (see“correct”above). (Visit AndersenLuminAire.com/Install to view a video of this step.)
a3 Repeat steps for Endcap A. Be sure the Screen Tracks are all the way into the Passive Housing.
C
C
32
36
PASSIVE
SCREEN
A
C
36
32
C
PASSIVE
SCREEN
PASSIVE
HOUSING
SCREEN
TRACK C
SCREEN
TRACK C
CHANNEL
(FOR SCREEN TRACK)
CHANNEL
(FOR SCREEN TRACK)
ENDCAP C
C
A
C
A
A
C
36
32
C
PASSIVE
SCREEN
CORRECT INCORRECT
RECEIVING TAB
(FITS INSIDE SCREEN TRACK)
RECEIVING TAB
(FITS INSIDE SCREEN TRACK)
RECEIVING TAB SHOULD NOT
BE OUTSIDE SCREEN TRACK
ALL ITEMS DURING THE ASSEMBLY STEPS
SHOULD BE LAYING FLAT ON THE GROUND
bReceiving Tabs on the Endcaps must
slide inside the Screen Track. Product
damage may occur if ReceivingTab is
forced outside the screen track.
NOTICE
Visit AndersenLuminAire.com/install
to view a video of this step.
Track Extender C

5
PLACE, FASTEN
ASSEMBLY
INTO OPENING
3
c1 Slide the Screen Assembly in the door opening until the Active Housing
side Screw Flange is on the Mounting Surface.
c2 Verify the Screen Assembly is plum, level and square in the door opening
and the Screen Housing side Screw Flange is tight to Mounting Surface.
b1 The Screen Assembly will be narrower than your opening until fully
expanded in the following steps.
b2 Start by placing the Screen Assembly onto the exterior Trim Surface
with the Screw Flanges extending into the Door Opening. Rest the
bottom of the screen assembly onto your sill or support blocking.
SCREEN
ASSEMBLY
DOOR
OPENING
MOUNTING
SURFACE
MOUNTING
SURFACE
SCREW
FLANGE
SCREW
FLANGE
TRIM
SURFACE
b
SCREW
FLANGE
MOUNTING
SURFACE
SLIDE
SLIDE
PRIMARY
ACTIVE
DOOR
PRIMARY
ACTIVE
DOOR
ACTIVE
HOUSING
ACTIVE
HOUSING
ACTIVE
HOUSING
DOOR OPENING DOOR OPENING
PASSIVE
HOUSING
PASSIVE
HOUSING
a1 With a Scissors, cut the Plastic Wrap along inside edge of the Screw Flange from new housing.
a2 With the interior of the screen assembly facing the door opening, rotate the assembly so the
Active Housing is on the same side of the Door Opening as your Primary Active Door.
a
OR
c
To avoid product damage. It is recommended to use two (2)
people to install double door unit into the door opening.
NOTICE
Tools Recommended:
Screwdriver
PLASTIC WRAP
SCISSORS
SCREW FLANGE
Scissors

6
f1 From the interior, while holding the Active Housing side Screw Flange tight
to the Mounting Surface, align the three holes on Screw Flange with the
three existing holes in the Mounting Surface. Extend the screen so it is clear
of your drill/driver. Remove orange installation clips and disposed of properly.
f2 With the three remaining #8 - 1"screws, fasten Passive Housing
to the Mounting Surface. (Be careful not to overtighten)
PLACE, FASTEN
ASSEMBLY
INTO OPENING
Continued
3
Tools Recommended:
e1 Expand the screen assembly in the door opening until the
Passive Housing side Screw Flange is on the Mounting Surface.
e2 Verify the screen assembly is plum, level and square in the door
opening and the Passive Housing side Screw Flange is tight to
Mounting Surface.
d1 From the interior, while holding the Active Housing side Screw Flange
tight to the Mounting Surface, align the three holes on Screw Flange with
the three existing holes in the Mounting Surface.
d2 With one #8 - 1"screw, fasten Active Housing to the Mounting Surface.
(Be careful not to overtighten)
d3 Repeat steps for top and bottom holes. (Being careful not to overtighten)
f
MOUNTING
SURFACE
MOUNTING
SURFACE
ACTIVE
HOUSING
SCREW
FLANGE
SCREW
FLANGE #8 - 1"
SCREW
EXPAND
EXPAND
PASSIVE
HOUSING
#8 - 1"
SCREW
MOUNTING
SURFACE
MOUNTING
SURFACE
SCREW
FLANGE
SCREW
FLANGE
e
Switch to Interior View
d
Screwdriver
#8-1"
(Qty 6)
SCREW PACK
#8
#10
#12
#6
3/4” Machine Pan Painted
1/2” SMS Pan
1/2” SMS Pan Painted
1/2” SMS Flathead
1/2” Self-Drill Pan
1/2” Self-Drill Pan Painted
3/4” Machine Flathead
7/8” Machine Pan Painted
1” SMS Pan
1” SMS Pan Painted
1” Machine Pan Painted
1-1/2” Machine Flathead
1-1/2” Machine Flathead
2” SMS Pan Painted
5/8” SMS Pan Painted
1-1/4” SMS Pan

7
PLACE AND
FASTEN SILL
ADAPTER
Tools Recommended:
a1 Thoroughly clean the Door Sill with soft cloth.
a2 From the interior of screen assembly, position Sill Adapter with the
textured side up and screw holes toward the interior of the home.
a3 Insert edge of the Sill Adapter into the Adapter Channel located on the Screen Track (see Figure 1).
a4 Rotate the Sill Adapter down to the Door Sill. Make sure the six holes in the Sill Adapter align with
the six existing holes in your Door Sill (see Figure 2)..
b1 Lift Sill Adapter and apply sealant into the holes until sealant overows onto Door Sill surface (see Figure 3).
b2 Rotate the Sill Adapter back down to the Door Sill and fasten using six #8 - ½"Self-Tapping Screws. Cleanup excess sealant.
(see Figure 4)
b
SCREEN
TRACK
SILL
ADAPTER
SILL ADAPTER
SILL
ADAPTER
DOOR
SILL
DOOR
SILL
DOOR
SILL
ADAPTER
CHANNEL
ADAPTER
CHANNEL
SILL
ADAPTER
#8 - ½ "
SCREW
SILL
ADAPTER
DOOR
SILL
DOOR
SILL
4
Sill Adapter
a
Figure 1
Figure 3
Figure 2
Figure 4
Drill/Driver
Sealant
#2 Phillips Bit
(provided)
SCREW PACK
#8 - ½"
(Qty 6)
#8
#10
#12
#6
3/4” Machine Pan Painted
1/2” SMS Pan
1/2” SMS Pan Painted
1/2” SMS Flathead
1/2” Self-Drill Pan
1/2” Self-Drill Pan Painted
3/4” Machine Flathead
7/8” Machine Pan Painted
1” SMS Pan
1” SMS Pan Painted
1” Machine Pan Painted
1-1/2” Machine Flathead
1-1/2” Machine Flathead
2” SMS Pan Painted
5/8” SMS Pan Painted
1-1/4” SMS Pan

8
ADJUSTMENT,
SLOT COVER &
CORNER PILE
INSTALLATION
Tools Recommended:
5
b1 Once the Locking Pins have been adjusted and set, unlatch and open
both screens.
b2 Reinstall a Slot Cover into the upper Adjustment Slot until the
Lock Legs snap into place and it is rmly seated in place.
b3 Repeat for the lower Adjustment Slot.
c1 Peel paper from back of Corner Pile and place at the top of the Passive
Housing Screen Pull against the Glide and rmly press into place.
c2 Repeat step for other end of the Passive Housing Screen Pull.
a1 Inside the Upper Adjustment Slot, keeping the Phillips Screwdriver in
contact with the screw, loosen the screw until it can be moved, approximately
2 turns; do not fully remove the screw. Use the Phillips Screwdriver to slide
the upper pin up towards the Screen Track until it stops. Tighten screw down.
a2 Inside the Lower Adjustment Slot, keeping the Phillips Screwdriver
in contact with the screw, loosen the screw until it can be moved,
approximately 2 turns; do not fully remove the screw. Use the Phillips
Screwdriver to slide the lower pin down towards the Screen Track until
it stops. Tighten screw down.
SCREEN
TRACK
GLIDE
SCREEN TRACK
CORNER
PILE
CORNER
PILE
SLOT
COVER
ADJUSTMENT
SLOT
ADJUSTMENT
SLOT
SLOT
COVER
LOCK
LEGS
PASSIVE
HOUSING
SCREEN PULL
PASSIVE
HOUSING
SCREEN PULL
PHILLIPS
SCREWDRIVER
UPPER
ADJUSTMENT SLOT
LOWER
ADJUSTMENT
SLOT
a b
c
REINSTALL SCREW PACK
Corner PileSlot Covers
Screwdriver

9
1-844-813-6664
RETRACTABLE SCREEN DOOR