Elite Screens Manual SRM Pro Series Instruction manual

Elite Screens Slow Retract Manual Series Square Housing Dimension Table
Manual SRM Pro Series
Unit: mm
Model
Screen
diagonal
Aspect
ratio
Overall
case
length (A)
Screen
material
Width.
（
A2
）
View
width
(A1)
Weight
bar
length
(A3)
Bottom
black
masking
border
with
weight
bar
（
B2
）
Screen
material
Height with
weight bar
(B3)
View
Height
(B1)
Screen
overall
height
with
weight
bar
(
B)
End
cap
height
(B4)
End
cap
width
(C)
Distance
from
screen
material
to the
wall (C1)
Top
black
masking
border
(B5)
G.W.
(KGS)
L
(mm)
W
(mm)
H
(mm)
M84HSR-Pro 84" 16:9 2014 1936 1860 2010 62 1298 1046 1394 96 80 20 190 8,24 2112 140 132
M100HSR-Pro 100" 16:9 2374 2290 2214 2370 62 1517 1245 1613 96 80 20 210 9,58 2472 140 130
M120HSR-Pro 120" 16:9 2816 2733 2657 2812 62 1746 1494 1842 96 80 20 190 #### 2984 160 140
M84VSR-Pro 84" 4:3 1867 1783 1707 1863 62 1432 1280 1528 96 80 20 90 9,24 1965 150 140
M100VSR-Pro 100" 4:3 2192 2108 2032 2188 62 1766 1524 1862 96 80 20 180 9,48 2290 145 140
M120VSR-Pro 120" 4:3 2598 2514 2438 2594 62 2066 1829 2162 96 80 20 175 #### 2666 140 135
Packing dimension
Note: Data Error ±1"
* Dimension Table is only for reference, actual item might be different. Subject to change w/o notice.

www.elitescreens.eu
Manual SRMPro
QUICK USER’S GUIDE
Screen Installation
A. Flush Wall Installation
1. Measure the distance of the keyholes on the end caps and mark the location of where
the screen is to be installed for the pre-drilled hole.
2. After marking the area and drilling the hole, insert the proper screw into the drilled hole
and leave about 1/8” of an inch from the wall to mount the screen.
3. Mount your screen from the keyhole located on back of screen’s left and right end caps.
Note: Do not remove the end caps to mount the screen to the wall.
Removing the end caps will release the tension of the internal spring mechanism.
(additional
hardware
required)
Optional
installation using
chains to hang the
screen from the ceiling.
1. You can also hang the screen on a ceiling by using a
chain (not included) and hang it by the two D-ring loops
located on the left and right side end caps.
Wall Mounting Screws Tip: For drywall installations, drywall
anchors and screws can be utilized to hang the screen from the
keyholes of the end caps. Please consult with a hardware store
for for your specific wall or ceiling installation.
Screen Operation
1. Pull the screen down from the lanyard or from the
handle only in a 90-degree angle. The screen is designed to
stop at any location. To achieve this, make sure to pull
straight down and allowing the screen to come up to lock
into place. Do not attempt to pull the screen down by the
surface or touch the screen, as it will damage the screen
and void the warranty.
2. To retract the screen, simply pull the screen down
more than 2 inches and retract the screen back releasing it
up gently. The screen is equipped with a SLOW
RETRACT MECHANISM which allows the screen to
slowly retract without the need to hold on to the handle or
lanyard.
Simply release the handle and the screen will retract by itself into the housing.
Attention: If the screen does not unlock, carefully pull the screen straight down with a little force. Always
pull the screen down at a 90 degree angle.
Side view
Front view
Keyhole located on
back of end cap
B. Ceiling Installation
proper
screws
D-ring

___________________________________
www.elitescreens.eu
[e-mail]
ELITE SCREENS
How to adding the spring force for Manual SRM Pro screen
1. Put the screen on the clean table, pull the material down a little and make it is in the
locked state. As the picture shown below.
2. Remove the screws on the left end cap with a screwdriver, and remove the left end cap,
and move the axis out a little. As the picture shown below.
3. Install the left end cap , rotating it in clockwise direction, release the locking, use one
hand to hold the axis, remove the end cap to release the spring force.（This step need
to be operated twice, to prevent the original spring force didn’t remove completely

___________________________________
www.elitescreens.eu
[e-mail]
and affect the effect of re-adding the spring force）
4. Install the left end cap on the plastic part of the spring, rotating it in clockwise
direction to add the spring force(rotating 10 laps), rotating it to a jammed point, that is,
you feel the spring will not reverse by itself ,then you can release your hand.(when
adding the spring force, pay attention to hold the end cap tightly to avoid it turn over
and hitting hand)
5. Hold the right end cap with hand, pull up the axis with a rope, then at the other end
need another person to pull the axis into the housing ,insert the axis into the right end
cap inner slot .
right end cap left end cap

___________________________________
www.elitescreens.eu
[e-mail]
6. Fixed the left end cap with the screws.