Draper Luma User manual

TOOLS
REQUIRED
Pencil
Tape Measure
Level
Power Drill
Hardware
(by Others)
Section 1 - Installation
1. Your Draper screen can be mounted on a wall or suspended from the ceiling or extension brackets.
It must be mounted level and with the flat back parallel to the wall.
The screen (or extension brackets) should be mounted into studs or blocking in the wall/ceiling, or
in drywall (minimum thickness ½”) with specified anchors. For any other type of installation, follow
all local building and safety codes.
Steel studs, concrete or cinder block walls and all other types of non-wood frame construction
require the use of special screws or anchors.
The selection of appropriate mounting hardware should be made by a qualified professional installer.
Dowel
Viewing
Surface
Wall or Ceiling
Mounting Bracket
CAUTION
1. Read and understand these instructions; keep them for
future reference. Follow instructions carefully. Failure to do
so invalidates warranty.
2. Care in both mounting and correct operation will mean long
and satisfactory service from your Draper screen.
3. Locate the screen where the audience can best see it, and
where other room furnishings permit.
4. Mount the screen so that the bottom of the picture, when
screen is fully extended, will be above the heads of viewers.
5. When raising screen, pull down and, while holding, allow
for slow retraction into the case to reduce risk of injury from
falling screen.
6. Screen should be installed level (using a carpenter’s level).
7. Nothing should be fastened to screen dowel or viewing
surface.
Please Note: Custom products/installations may not be reflected
by this document. Call Draper, Inc. if you have questions about
your installation.
Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385
draperinc.com | 765.987.7999 | 800.238.7999
© 2017 All Rights Reserved | FORM: Luma_Inst17
INSTRUCTIONS
INSTALLATION & OPERATION
Luma
Spring-roller operated projection screen that can be wall or ceiling mounted

Figure (1)
Crimp
Crimp
Figure (2)
Figure (3)
Clip Assembly
Screen
Hanger Nut
Crimp
Crimp
Section 1 - Installation (Continued)
Section 1.1 - Ceiling Suspended Mounting to Joists (Hardware Not Included)
1. Use the holes at the front of the endcap/mounting bracket for suspended mounting.
Position and properly anchor screw eyes or other fasteners (not included) into ceiling joists or other solid surface.
Suspend “S” hooks (not included) from fasteners (not included) and hook through holes in the front of the mount-
ing bracket. For added safety, crimp both ends of the “S” hooks so the screen cannot come off.
Recommended hardware (not included):
For mounting into wood or ceiling joist, use two 3/
16
” x 1¼” screw eyes and 3/
16
” diameter “S” hooks;
for mounting into drywall (minimum ½” thick), use 3/
16
” toggle or molly bolts with 3/
16
” “S” hooks.
Section 1.2 - Ceiling Suspended Mounting - T-Bar Twist Clips (Optional)
1. Loosen the clip assembly by turning the formed steel hanger counterclockwise.
2. Spread the clip assembly apart, place over the T-irons, and firmly squeeze the clip assembly back together,
making sure the clip is firmly seated around the T-iron. Retighten by using pliers to turn the formed steel hang-
er clockwise. Make sure it is fully tightened.
3. Secure with the nut. Tighten with pliers.
Please Note:
Make sure the clip is fully tightened around the T-iron, and that the formed steel hanger and the lock nut are fully
tightened. Poorly tightened clip assemblies, hangers or nuts allow the T-Bar Twist Clip to work loose.
4. Test by trying to pull the twist clip open and by pulling down on the hanger. The clip should not pull open.
5. Suspend provided “S” hooks from the holes in the clips and hook through holes in the front of the screen
mounting bracket. For added safety, crimp both ends of the “S” hooks so the screen cannot come off.
Please Note:
T–Bar Twist Clips are not recommended for screens larger than 70” x 70” unless T-irons are reinforced.
Section 1.3 - Wall Mounting (Hardware Not Included)
1. Use the upper portion of the holes at the back of the endcap/mounting bracket for flush wall mounting.
Recommended hardware (not included):
For mounting into wood or wall stud, use #10 x 1¼” wood screws;
for mounting into drywall (minimum ½” thick), use 3/16” toggle or molly bolts.
DO NOT USE FLAT HEAD SCREWS. DO NOT OVERTIGHTEN.
Section 1.4 - Extension Brackets (Optional Equipment)
1. Wall mount the brackets (not included with screen) using hardware recom-mended for “Wall Mounting” (above,
not included). Then, suspend the screen from the front holes with “S” hooks. For added safety, crimp both
ends of the “S” hooks so the screen cannot come off.
DO NOT OVERTIGHTEN.
Please note: When installing wall brackets, flexible driver bit extensions may
make it easier to accurately drive the fasteners into the mounting surface.
Section 2 - Operating Instructions
Section 2.1 - Standard
To lower picture surface: pull screen down. Hesitate—then allow screen to retract very slowly until it locks in place.
To raise picture surface: pull screen down and, while holding, allow for slow retraction into the case to reduce risk of
injury from falling screen.
Section 2.2 - AutoReturn
To lower picture surface: pull screen down. Hesitate—then allow screen to retract very slowly until it locks in place.
To raise picture surface: pull screen down gently until it stops, then release.
Figure (4)
DO NOT mount screens with plastic
endcaps to metal wall brackets in
the manner shown above.
Luma page 2 of 2