&Tradition Collect Planter SC43 Space Copenhagen 2020 User manual

Congratulations with your new Collect Planter
designed in 2020 by Space Copenhagen. We hope
you will enjoy using this product and follow these
instructions to ensure correct installation. If you have
any questions or comments, please do not hesitate to
contact us by mail on:
in[email protected]
Collect | Planter SC43-45
Space Copenhagen
2020
Instructions

Please read these instructions carefully and retain them
for future reference to ensure that the product is used
correctly. For your own safety, please study each step of
this instruction manual first. &Tradition is not responsible
for any faults or damages caused by not following these in-
structions correctly. Do not modify this product in any way.
Contents
AContains one of the following:
SC43
SC44
SC45
BContains one of the following sleeves:
SC43
SC44
SC45
CSelf-watering insert
D 3 x Planter feet
NB: The sleeve and self-watering insert is only intended
for interior use, please recycle (B) & (C) properly if not
used.
Tools needed
- Spirit level
- Nail
- Electric drill
- Clay pebbles
Safety precautions
- The planter can be used for both exterior and interior use
- For interior use we recommend using the 3 planter
feet to lift the planter o the substrate to provide extra
aeration.
-For exterior use please follow step 1 through 4 on the
following page. For interior use please do not modify the
product.
- When drilling drainage holes in the planter, please be
aware never to use a hammer drill as this will damage
the planter.
SC44 SC45
A
B
CD
SC43
SC44 SC45SC43
Collect | Planter SC43-45
Space Copenhagen
2020

Cleaning instructions
- Fiber concrete can be cleaned with a soft cloth wrung
in a mild solution of lukewarm water and an universal
cleaning detergent. Always wipe with a soft dry cloth
after cleaning.
- Do not use heavy abrasive, bleach-based, ammoniated
cleansers or citrus-based cleansers.
- For securing a healthy plant, it is recommended to allow
the water to be absorbed. This can either be done by
placing clay pebbles in the bottom of the planter or by
making your own drainage holes.

Preparation for exterior use:
Step 1
When drilling your own drainage holes, place the planter
upside down on a soft, flat surface.
Step 2
Using a spirit level, mark the placement of 5 holes.
Place the 5 holes at the following position:
1 in the center of the pot base
4 arranged in a square pattern.
Keep holes at least 2,5 cm from the edge of the planter.
Step 3
Press a small indentation into the marked spot with a nail
to prevent the bit from slipping away from the spot on a
smooth surface.
Step 4
Place the drill bit in the indentation, holding the drill so
the bit is perpendicular to the pot base.
Please be aware never to use a hammer drill as this will
damage the planter.
Drill 5 holes at the slowest speed.

Preparation for interior use:
Step 1
Place the Planter (A) onto the Planter feet (D).
Step 2
For Planter SC43 please skip this step and continue to
step 3. For Planter SC44 fill in 17 cm of pebbles in the
bottom of the planter. For SC45 fill in 21 cm of pebbles.
Step 3
Place the sleeve (B) into the planter (A).
Step 4
For Planter SC43 place pebbles down the sides of the
sleeve (B) to make it more stable.
For SC44 & SC45 please skip this step and move on to
step 5

Step 5
Place the self-watering insert (C) into the sleeve (B),
Make sure that the lid is kept above the top edge of the
sleeve, so it’s not covered with soil.
Step 5
Place 4 cm of clay pebbles in the bottom of the sleeve.
Step 6
Add soil and a plant untill the sleeve (B) is covered, the lid
of the self-watering insert (C) should still be uncovered
and free of soil.

Step 7
Take the lid o the self-watering insert (C).
Step 8
Fill water into the self-watering insert (C) untill the
meassuring stick starts to rise.
Step 9
Put the lid back on. The measuring stick should be levelling
between ‘opt.’ and ‘max.’. Check on your plant regulary and
when the meassure stick reaches ‘min.’ please refill with
water.

andtradition.com