Anjou AJ-PCN082 User manual
AJ-PCN082
Input: 100-240V~ 50/60Hz
Output: DC 24V 0.5A
<10W
>5h (High Mist)
>8h (Low Mist)
60 ml / 2.0 fl. oz (High Mist)
30 ml / 1.0 fl. oz (Low Mist)
300 ml / 10.0 fl. oz
2.4MHz
Model: AJPCN082
Anjou Aroma Diffuser
User Guide
Product Diagram
1
2
6
4
8
910 11
12
5
7①Nozzle
②Tank Cover
③Muting Cover
④Essential Oil Tube
⑤Water Tank
⑥Drain Side
Specifications
Model
Power Adapter
Power
Working Time
Mist Output
Water Tank Volume
Ultrasonic Frequency
Package Contents
· 1 x Aroma Diffuser
· 1 x Power Adapter
· 1 x Cleaning Brush
· 1 x Essential Oil Tube
· 1 x User Guide
· 1 x Thank You Card
3
How to Use
Caution
1. Please add water to the tank first, then add essential oils up to the
marking on the tube or until dispensing starts. If there's no
fragrance, the water-oil balance may be off. Please add enough
essential oil as instructed then.
1H 3H 6H ON
2. It is recommended to use purified or distilled water.
3. Cinnamon essential oil is of higher density and viscosity than that
of water. When adding the cinnamon essential oil to the water, it will
sink to the bottom. It is recommended that the essential oil be
added directly on the water surface to accelerate diffusion.
Add and Drain Water
1. Remove the tank cover, add water into the tank no higher than the
max water level. Add a few drops of essential oil into the tube
until it spills out slightly. Put the tank cover back on.
3. Clean the water tank with the included brush when grime builds up.
Note:
Never pour essential oils into the tube when there is no water inside
the tank.
2. Drain excess water via the drain side if necessary.
1H 3H 6H ON ⑦Timer Indicators
⑧Base
⑨Light Button
⑩Timer Button
⑪Power / Mist Button
⑫Power Port
1H 3H 6H ON
1H 3H 6H ON
1H 3H 6H ON 1H 3H 6H ON
Timer Setting:
When the unit is on, press to set 1 / 3 / 6 hours
timer. The corresponding indicator will light up.
Timer OFF:
When the timer is on, press and hold for 2
seconds to turn off the timer at any time.
Automatic Color Changing:
Press once to enter automatic color changing
mode where 7 colors will be cycled through.
Select Color:
Press again to stay on the current color. Keep
pressing to cycle through different colors.
Press and hold for 2 seconds to turn off the mist.
Switch between High & Low Mist:
Press again to resume High Mist. Switch
between the two modes with each press.
Low Mist:
Press again to enter low mist mode with one
beep sound.
High Mist:
Press once to enter the default high mist mode.
Two beeps will sound and the ON indicator will
light up.
Operations and Functions
Connect to a power source. Once connected,the diffuser will enter
standby mode. Please make sure there is enough water inside the tank.
OperationsFunctions
Mist ON
Mist OFF
Timer
Setting
Light Mode
Setting
Low Water Protection
The diffuser will turn off automatically when water inside the tank has
been depleted. Once water is added back into the tank, the diffuser
will resume standby mode.
How to Clean
IMPORTANT!
Please unplug the unit before cleaning!
Regular Cleaning
1) Empty the tank from the water outlet.
2) Add 3-5g (approx. one teaspoon, based on scale of the residues)
baking soda / NaHCO3 to the tank.
3) Fill the tank halfway full with warm water (200-250ml / 6.76-8.45fl
oz, 50°C / 122°F), stir it to fully dissolve.
4) Soak for 3-5mins, wipe down the tank and tank cover using a small
brush or soft cloth with baking soda solution. (For better cleaning,
remove the muting cover and wipe it down thoroughly).
5) Drain the solution and rinse the tank under tap water.
6) Rub the inside and outside dry with a dry towel or clean cloth.
7) Wipe off the soda residues if any.
Deep Cleaning
You are recommended to deep clean your diffuser once a month or
when the mist output is low due to grime build-up.
1) Empty the tank from the water outlet.
2) Add 2-3 teaspoons of baking soda / NaHCO3, or 2-3 slices of fresh
lemon to the tank.
3) Fill the tank halfway full with warm water (200-250ml / 6.76-8.45fl
oz, 50°C / 122°F), stir it to fully dissolve.
4) Soak for about half an hour.
5) Thoroughly clean the grime at the bottom and atomizer (slot at the
center) of the tank with a small brush.
6) Wipe down tank cover using a small brush or soft cloth with baking
soda solution. (For better cleaning, remove the muting cover and
wipe it down thoroughly).
7) Drain the solution and rinse the tank under tap water.
8) Wipe off the soda residues if any.
9) Rub the inside and outside dry with a dry towel or clean cloth.
Notes:
1) You may use dishwashing detergent when baking soda is
unavailable. But it works better for oil removing instead of odor
and mineral buildup.
2) Do not rinse the base directly with water; try to avoid wetting the
buttons, light holes, air inlets and underneath to avoid short circuit.
3) It is not recommended to clean the unit with white vinegar since
its direct and indirect contact with the atomizer will damage it
permanently.
Troubleshooting
No. Problem Solution
1
The LED light is not
turned on when powered
on.
Press the Light Button to turn
on the light.
2
The unit stops misting
with the light flashing
red as over-temperature
alarm.
• Turn off the unit.
• Pay attention to the
environmental temperature
and place the unit in a
well-ventilated place to cool
down.
• Do not add warm water into
the tank.
3The mist output is
becoming low.
• Keep the water clean or use
purified or distilled water.
• Clean the atomizer regularly.
4
Mist level is becoming
low, and finally stops
misting.
Add water if there is not
enough water in the water
tank.
5Scales in the water tank
and water reservoir
Clean the unit as instructed in
the Cleaning and Maintenance
section.
6Strange odor after long
idle time
Clean the unit thoroughly
before use.
No. Problem Solution
7
Previously used
essential oil smell
remains in the unit.
Clean the unit thoroughly
before use.
8 Diffusion not enough Turn on the High Mist mode.
9 Wet table surface
The mist level is too high for
the small space. Please lower
the mist level.
10 Fragrance not strong
enough
Add the essential oil into the
tube until it spills out slightly.
11
No fragrance after
adding cinnamon
essential oil
Cinnamon essential oil
is of higher density and
viscosity than that of water.
It is recommended that the
essential oil be added directly
on the water surface to
accelerate the diffusion.
12 Failed to select one
color
Press the Light Button once
to enter automatic color
changing mode. Press it
again to stay on the current
color. Keep pressing to cycle
through different colors.
ENEN
DE
Produktabbildung ⑦Timer
⑧Basis
⑨Lichttaste
⑩Tim e r-Ta s te
⑪Power- / Nebeltaste
⑫Stromanschluss
①Zerstäuberdüse
②Tankabdeckung
③Dämpfende Abdeckung
④Röhrchen für ätherische Öle
⑤Max. Wasserfüllstand
⑥Seitenablauf
1 2 3 4 5 6 7 8 9 10
AJ-PCN082
Input: 100-240V~ 50/60Hz
Output: DC 24V 0.5A
<10W
>5h (High Mist)
>8h (Low Mist)
60 ml / 2.0 fl. oz (High Mist)
30 ml / 1.0 fl. oz (Low Mist)
300 ml / 10.0 fl. oz
2.4MHz
Model: AJPCN082
Anjou Aroma Diffuser
User Guide
Product Diagram
1
2
6
4
8
910 11
12
5
7①Nozzle
②Tank Cover
③Muting Cover
④Essential Oil Tube
⑤Water Tank
⑥Drain Side
Specifications
Model
Power Adapter
Power
Working Time
Mist Output
Water Tank Volume
Ultrasonic Frequency
Package Contents
· 1 x Aroma Diffuser
· 1 x Power Adapter
· 1 x Cleaning Brush
· 1 x Essential Oil Tube
· 1 x User Guide
· 1 x Thank You Card
3
How to Use
Caution
1. Please add water to the tank first, then add essential oils up to the
marking on the tube or until dispensing starts. If there's no
fragrance, the water-oil balance may be off. Please add enough
essential oil as instructed then.
1H 3H 6H ON
2. It is recommended to use purified or distilled water.
3. Cinnamon essential oil is of higher density and viscosity than that
of water. When adding the cinnamon essential oil to the water, it will
sink to the bottom. It is recommended that the essential oil be
added directly on the water surface to accelerate diffusion.
Add and Drain Water
1. Remove the tank cover, add water into the tank no higher than the
max water level. Add a few drops of essential oil into the tube
until it spills out slightly. Put the tank cover back on.
3. Clean the water tank with the included brush when grime builds up.
Note:
Never pour essential oils into the tube when there is no water inside
the tank.
2. Drain excess water via the drain side if necessary.
1H 3H 6H ON ⑦Timer Indicators
⑧Base
⑨Light Button
⑩Timer Button
⑪Power / Mist Button
⑫Power Port
1H 3H 6H ON
1H 3H 6H ON
1H 3H 6H ON 1H 3H 6H ON
Timer Setting:
When the unit is on, press to set 1 / 3 / 6 hours
timer. The corresponding indicator will light up.
Timer OFF:
When the timer is on, press and hold for 2
seconds to turn off the timer at any time.
Automatic Color Changing:
Press once to enter automatic color changing
mode where 7 colors will be cycled through.
Select Color:
Press again to stay on the current color. Keep
pressing to cycle through different colors.
Press and hold for 2 seconds to turn off the mist.
Switch between High & Low Mist:
Press again to resume High Mist. Switch
between the two modes with each press.
Low Mist:
Press again to enter low mist mode with one
beep sound.
High Mist:
Press once to enter the default high mist mode.
Two beeps will sound and the ON indicator will
light up.
Operations and Functions
Connect to a power source. Once connected,the diffuser will enter
standby mode. Please make sure there is enough water inside the tank.
OperationsFunctions
Mist ON
Mist OFF
Timer
Setting
Light Mode
Setting
Low Water Protection
The diffuser will turn off automatically when water inside the tank has
been depleted. Once water is added back into the tank, the diffuser
will resume standby mode.
How to Clean
IMPORTANT!
Please unplug the unit before cleaning!
Regular Cleaning
1) Empty the tank from the water outlet.
2) Add 3-5g (approx. one teaspoon, based on scale of the residues)
baking soda / NaHCO3 to the tank.
3) Fill the tank halfway full with warm water (200-250ml / 6.76-8.45fl
oz, 50°C / 122°F), stir it to fully dissolve.
4) Soak for 3-5mins, wipe down the tank and tank cover using a small
brush or soft cloth with baking soda solution. (For better cleaning,
remove the muting cover and wipe it down thoroughly).
5) Drain the solution and rinse the tank under tap water.
6) Rub the inside and outside dry with a dry towel or clean cloth.
7) Wipe off the soda residues if any.
Deep Cleaning
You are recommended to deep clean your diffuser once a month or
when the mist output is low due to grime build-up.
1) Empty the tank from the water outlet.
2) Add 2-3 teaspoons of baking soda / NaHCO3, or 2-3 slices of fresh
lemon to the tank.
3) Fill the tank halfway full with warm water (200-250ml / 6.76-8.45fl
oz, 50°C / 122°F), stir it to fully dissolve.
4) Soak for about half an hour.
5) Thoroughly clean the grime at the bottom and atomizer (slot at the
center) of the tank with a small brush.
6) Wipe down tank cover using a small brush or soft cloth with baking
soda solution. (For better cleaning, remove the muting cover and
wipe it down thoroughly).
7) Drain the solution and rinse the tank under tap water.
8) Wipe off the soda residues if any.
9) Rub the inside and outside dry with a dry towel or clean cloth.
Notes:
1) You may use dishwashing detergent when baking soda is
unavailable. But it works better for oil removing instead of odor
and mineral buildup.
2) Do not rinse the base directly with water; try to avoid wetting the
buttons, light holes, air inlets and underneath to avoid short circuit.
3) It is not recommended to clean the unit with white vinegar since
its direct and indirect contact with the atomizer will damage it
permanently.
Troubleshooting
No. Problem Solution
1
The LED light is not
turned on when powered
on.
Press the Light Button to turn
on the light.
2
The unit stops misting
with the light flashing
red as over-temperature
alarm.
• Turn off the unit.
• Pay attention to the
environmental temperature
and place the unit in a
well-ventilated place to cool
down.
• Do not add warm water into
the tank.
3The mist output is
becoming low.
• Keep the water clean or use
purified or distilled water.
• Clean the atomizer regularly.
4
Mist level is becoming
low, and finally stops
misting.
Add water if there is not
enough water in the water
tank.
5Scales in the water tank
and water reservoir
Clean the unit as instructed in
the Cleaning and Maintenance
section.
6Strange odor after long
idle time
Clean the unit thoroughly
before use.
No. Problem Solution
7
Previously used
essential oil smell
remains in the unit.
Clean the unit thoroughly
before use.
8 Diffusion not enough Turn on the High Mist mode.
9 Wet table surface
The mist level is too high for
the small space. Please lower
the mist level.
10 Fragrance not strong
enough
Add the essential oil into the
tube until it spills out slightly.
11
No fragrance after
adding cinnamon
essential oil
Cinnamon essential oil
is of higher density and
viscosity than that of water.
It is recommended that the
essential oil be added directly
on the water surface to
accelerate the diffusion.
12 Failed to select one
color
Press the Light Button once
to enter automatic color
changing mode. Press it
again to stay on the current
color. Keep pressing to cycle
through different colors.
ENEN
DE
Produktabbildung ⑦Timer
⑧Basis
⑨Lichttaste
⑩Tim e r-Ta s te
⑪Power- / Nebeltaste
⑫Stromanschluss
①Zerstäuberdüse
②Tankabdeckung
③Dämpfende Abdeckung
④Röhrchen für ätherische Öle
⑤Max. Wasserfüllstand
⑥Seitenablauf
1 2 3 4 5 6 7 8 9 10
AJ-PCN082
Input: 100-240V~ 50/60Hz
Output: DC 24V 0.5A
<10W
>5h (High Mist)
>8h (Low Mist)
60 ml / 2.0 fl. oz (High Mist)
30 ml / 1.0 fl. oz (Low Mist)
300 ml / 10.0 fl. oz
2.4MHz
Model: AJPCN082
Anjou Aroma Diffuser
User Guide
Product Diagram
1
2
6
4
8
910 11
12
5
7①Nozzle
②Tank Cover
③Muting Cover
④Essential Oil Tube
⑤Water Tank
⑥Drain Side
Specifications
Model
Power Adapter
Power
Working Time
Mist Output
Water Tank Volume
Ultrasonic Frequency
Package Contents
· 1 x Aroma Diffuser
· 1 x Power Adapter
· 1 x Cleaning Brush
· 1 x Essential Oil Tube
· 1 x User Guide
· 1 x Thank You Card
3
How to Use
Caution
1. Please add water to the tank first, then add essential oils up to the
marking on the tube or until dispensing starts. If there's no
fragrance, the water-oil balance may be off. Please add enough
essential oil as instructed then.
1H 3H 6H ON
2. It is recommended to use purified or distilled water.
3. Cinnamon essential oil is of higher density and viscosity than that
of water. When adding the cinnamon essential oil to the water, it will
sink to the bottom. It is recommended that the essential oil be
added directly on the water surface to accelerate diffusion.
Add and Drain Water
1. Remove the tank cover, add water into the tank no higher than the
max water level. Add a few drops of essential oil into the tube
until it spills out slightly. Put the tank cover back on.
3. Clean the water tank with the included brush when grime builds up.
Note:
Never pour essential oils into the tube when there is no water inside
the tank.
2. Drain excess water via the drain side if necessary.
1H 3H 6H ON ⑦Timer Indicators
⑧Base
⑨Light Button
⑩Timer Button
⑪Power / Mist Button
⑫Power Port
1H 3H 6H ON
1H 3H 6H ON
1H 3H 6H ON 1H 3H 6H ON
Timer Setting:
When the unit is on, press to set 1 / 3 / 6 hours
timer. The corresponding indicator will light up.
Timer OFF:
When the timer is on, press and hold for 2
seconds to turn off the timer at any time.
Automatic Color Changing:
Press once to enter automatic color changing
mode where 7 colors will be cycled through.
Select Color:
Press again to stay on the current color. Keep
pressing to cycle through different colors.
Press and hold for 2 seconds to turn off the mist.
Switch between High & Low Mist:
Press again to resume High Mist. Switch
between the two modes with each press.
Low Mist:
Press again to enter low mist mode with one
beep sound.
High Mist:
Press once to enter the default high mist mode.
Two beeps will sound and the ON indicator will
light up.
Operations and Functions
Connect to a power source. Once connected,the diffuser will enter
standby mode. Please make sure there is enough water inside the tank.
OperationsFunctions
Mist ON
Mist OFF
Timer
Setting
Light Mode
Setting
Low Water Protection
The diffuser will turn off automatically when water inside the tank has
been depleted. Once water is added back into the tank, the diffuser
will resume standby mode.
How to Clean
IMPORTANT!
Please unplug the unit before cleaning!
Regular Cleaning
1) Empty the tank from the water outlet.
2) Add 3-5g (approx. one teaspoon, based on scale of the residues)
baking soda / NaHCO3 to the tank.
3) Fill the tank halfway full with warm water (200-250ml / 6.76-8.45fl
oz, 50°C / 122°F), stir it to fully dissolve.
4) Soak for 3-5mins, wipe down the tank and tank cover using a small
brush or soft cloth with baking soda solution. (For better cleaning,
remove the muting cover and wipe it down thoroughly).
5) Drain the solution and rinse the tank under tap water.
6) Rub the inside and outside dry with a dry towel or clean cloth.
7) Wipe off the soda residues if any.
Deep Cleaning
You are recommended to deep clean your diffuser once a month or
when the mist output is low due to grime build-up.
1) Empty the tank from the water outlet.
2) Add 2-3 teaspoons of baking soda / NaHCO3, or 2-3 slices of fresh
lemon to the tank.
3) Fill the tank halfway full with warm water (200-250ml / 6.76-8.45fl
oz, 50°C / 122°F), stir it to fully dissolve.
4) Soak for about half an hour.
5) Thoroughly clean the grime at the bottom and atomizer (slot at the
center) of the tank with a small brush.
6) Wipe down tank cover using a small brush or soft cloth with baking
soda solution. (For better cleaning, remove the muting cover and
wipe it down thoroughly).
7) Drain the solution and rinse the tank under tap water.
8) Wipe off the soda residues if any.
9) Rub the inside and outside dry with a dry towel or clean cloth.
Notes:
1) You may use dishwashing detergent when baking soda is
unavailable. But it works better for oil removing instead of odor
and mineral buildup.
2) Do not rinse the base directly with water; try to avoid wetting the
buttons, light holes, air inlets and underneath to avoid short circuit.
3) It is not recommended to clean the unit with white vinegar since
its direct and indirect contact with the atomizer will damage it
permanently.
Troubleshooting
No. Problem Solution
1
The LED light is not
turned on when powered
on.
Press the Light Button to turn
on the light.
2
The unit stops misting
with the light flashing
red as over-temperature
alarm.
• Turn off the unit.
• Pay attention to the
environmental temperature
and place the unit in a
well-ventilated place to cool
down.
• Do not add warm water into
the tank.
3The mist output is
becoming low.
• Keep the water clean or use
purified or distilled water.
• Clean the atomizer regularly.
4
Mist level is becoming
low, and finally stops
misting.
Add water if there is not
enough water in the water
tank.
5Scales in the water tank
and water reservoir
Clean the unit as instructed in
the Cleaning and Maintenance
section.
6Strange odor after long
idle time
Clean the unit thoroughly
before use.
No. Problem Solution
7
Previously used
essential oil smell
remains in the unit.
Clean the unit thoroughly
before use.
8 Diffusion not enough Turn on the High Mist mode.
9 Wet table surface
The mist level is too high for
the small space. Please lower
the mist level.
10 Fragrance not strong
enough
Add the essential oil into the
tube until it spills out slightly.
11
No fragrance after
adding cinnamon
essential oil
Cinnamon essential oil
is of higher density and
viscosity than that of water.
It is recommended that the
essential oil be added directly
on the water surface to
accelerate the diffusion.
12 Failed to select one
color
Press the Light Button once
to enter automatic color
changing mode. Press it
again to stay on the current
color. Keep pressing to cycle
through different colors.
ENEN
DE
Produktabbildung ⑦Timer
⑧Basis
⑨Lichttaste
⑩Tim e r-Ta s te
⑪Power- / Nebeltaste
⑫Stromanschluss
①Zerstäuberdüse
②Tankabdeckung
③Dämpfende Abdeckung
④Röhrchen für ätherische Öle
⑤Max. Wasserfüllstand
⑥Seitenablauf
1 2 3 4 5 6 7 8 9 10
AJ-PCN082
Input: 100-240V~ 50/60Hz
Output: DC 24V 0.5A
<10W
>5h (High Mist)
>8h (Low Mist)
60 ml / 2.0 fl. oz (High Mist)
30 ml / 1.0 fl. oz (Low Mist)
300 ml / 10.0 fl. oz
2.4MHz
Model: AJPCN082
Anjou Aroma Diffuser
User Guide
Product Diagram
1
2
6
4
8
910 11
12
5
7①Nozzle
②Tank Cover
③Muting Cover
④Essential Oil Tube
⑤Water Tank
⑥Drain Side
Specifications
Model
Power Adapter
Power
Working Time
Mist Output
Water Tank Volume
Ultrasonic Frequency
Package Contents
· 1 x Aroma Diffuser
· 1 x Power Adapter
· 1 x Cleaning Brush
· 1 x Essential Oil Tube
· 1 x User Guide
· 1 x Thank You Card
3
How to Use
Caution
1. Please add water to the tank first, then add essential oils up to the
marking on the tube or until dispensing starts. If there's no
fragrance, the water-oil balance may be off. Please add enough
essential oil as instructed then.
1H 3H 6H ON
2. It is recommended to use purified or distilled water.
3. Cinnamon essential oil is of higher density and viscosity than that
of water. When adding the cinnamon essential oil to the water, it will
sink to the bottom. It is recommended that the essential oil be
added directly on the water surface to accelerate diffusion.
Add and Drain Water
1. Remove the tank cover, add water into the tank no higher than the
max water level. Add a few drops of essential oil into the tube
until it spills out slightly. Put the tank cover back on.
3. Clean the water tank with the included brush when grime builds up.
Note:
Never pour essential oils into the tube when there is no water inside
the tank.
2. Drain excess water via the drain side if necessary.
1H 3H 6H ON ⑦Timer Indicators
⑧Base
⑨Light Button
⑩Timer Button
⑪Power / Mist Button
⑫Power Port
1H 3H 6H ON
1H 3H 6H ON
1H 3H 6H ON 1H 3H 6H ON
Timer Setting:
When the unit is on, press to set 1 / 3 / 6 hours
timer. The corresponding indicator will light up.
Timer OFF:
When the timer is on, press and hold for 2
seconds to turn off the timer at any time.
Automatic Color Changing:
Press once to enter automatic color changing
mode where 7 colors will be cycled through.
Select Color:
Press again to stay on the current color. Keep
pressing to cycle through different colors.
Press and hold for 2 seconds to turn off the mist.
Switch between High & Low Mist:
Press again to resume High Mist. Switch
between the two modes with each press.
Low Mist:
Press again to enter low mist mode with one
beep sound.
High Mist:
Press once to enter the default high mist mode.
Two beeps will sound and the ON indicator will
light up.
Operations and Functions
Connect to a power source. Once connected,the diffuser will enter
standby mode. Please make sure there is enough water inside the tank.
OperationsFunctions
Mist ON
Mist OFF
Timer
Setting
Light Mode
Setting
Low Water Protection
The diffuser will turn off automatically when water inside the tank has
been depleted. Once water is added back into the tank, the diffuser
will resume standby mode.
How to Clean
IMPORTANT!
Please unplug the unit before cleaning!
Regular Cleaning
1) Empty the tank from the water outlet.
2) Add 3-5g (approx. one teaspoon, based on scale of the residues)
baking soda / NaHCO3 to the tank.
3) Fill the tank halfway full with warm water (200-250ml / 6.76-8.45fl
oz, 50°C / 122°F), stir it to fully dissolve.
4) Soak for 3-5mins, wipe down the tank and tank cover using a small
brush or soft cloth with baking soda solution. (For better cleaning,
remove the muting cover and wipe it down thoroughly).
5) Drain the solution and rinse the tank under tap water.
6) Rub the inside and outside dry with a dry towel or clean cloth.
7) Wipe off the soda residues if any.
Deep Cleaning
You are recommended to deep clean your diffuser once a month or
when the mist output is low due to grime build-up.
1) Empty the tank from the water outlet.
2) Add 2-3 teaspoons of baking soda / NaHCO3, or 2-3 slices of fresh
lemon to the tank.
3) Fill the tank halfway full with warm water (200-250ml / 6.76-8.45fl
oz, 50°C / 122°F), stir it to fully dissolve.
4) Soak for about half an hour.
5) Thoroughly clean the grime at the bottom and atomizer (slot at the
center) of the tank with a small brush.
6) Wipe down tank cover using a small brush or soft cloth with baking
soda solution. (For better cleaning, remove the muting cover and
wipe it down thoroughly).
7) Drain the solution and rinse the tank under tap water.
8) Wipe off the soda residues if any.
9) Rub the inside and outside dry with a dry towel or clean cloth.
Notes:
1) You may use dishwashing detergent when baking soda is
unavailable. But it works better for oil removing instead of odor
and mineral buildup.
2) Do not rinse the base directly with water; try to avoid wetting the
buttons, light holes, air inlets and underneath to avoid short circuit.
3) It is not recommended to clean the unit with white vinegar since
its direct and indirect contact with the atomizer will damage it
permanently.
Troubleshooting
No. Problem Solution
1
The LED light is not
turned on when powered
on.
Press the Light Button to turn
on the light.
2
The unit stops misting
with the light flashing
red as over-temperature
alarm.
• Turn off the unit.
• Pay attention to the
environmental temperature
and place the unit in a
well-ventilated place to cool
down.
• Do not add warm water into
the tank.
3The mist output is
becoming low.
• Keep the water clean or use
purified or distilled water.
• Clean the atomizer regularly.
4
Mist level is becoming
low, and finally stops
misting.
Add water if there is not
enough water in the water
tank.
5Scales in the water tank
and water reservoir
Clean the unit as instructed in
the Cleaning and Maintenance
section.
6Strange odor after long
idle time
Clean the unit thoroughly
before use.
No. Problem Solution
7
Previously used
essential oil smell
remains in the unit.
Clean the unit thoroughly
before use.
8 Diffusion not enough Turn on the High Mist mode.
9 Wet table surface
The mist level is too high for
the small space. Please lower
the mist level.
10 Fragrance not strong
enough
Add the essential oil into the
tube until it spills out slightly.
11
No fragrance after
adding cinnamon
essential oil
Cinnamon essential oil
is of higher density and
viscosity than that of water.
It is recommended that the
essential oil be added directly
on the water surface to
accelerate the diffusion.
12 Failed to select one
color
Press the Light Button once
to enter automatic color
changing mode. Press it
again to stay on the current
color. Keep pressing to cycle
through different colors.
ENEN
DE
Produktabbildung ⑦Timer
⑧Basis
⑨Lichttaste
⑩Tim e r-Ta s te
⑪Power- / Nebeltaste
⑫Stromanschluss
①Zerstäuberdüse
②Tankabdeckung
③Dämpfende Abdeckung
④Röhrchen für ätherische Öle
⑤Max. Wasserfüllstand
⑥Seitenablauf
1 2 3 4 5 6 7 8 9 10
AJ-PCN082
Input: 100-240V~ 50/60Hz
Output: DC 24V 0.5A
<10W
>5h (High Mist)
>8h (Low Mist)
60 ml / 2.0 fl. oz (High Mist)
30 ml / 1.0 fl. oz (Low Mist)
300 ml / 10.0 fl. oz
2.4MHz
Model: AJPCN082
Anjou Aroma Diffuser
User Guide
Product Diagram
1
2
6
4
8
910 11
12
5
7①Nozzle
②Tank Cover
③Muting Cover
④Essential Oil Tube
⑤Water Tank
⑥Drain Side
Specifications
Model
Power Adapter
Power
Working Time
Mist Output
Water Tank Volume
Ultrasonic Frequency
Package Contents
· 1 x Aroma Diffuser
· 1 x Power Adapter
· 1 x Cleaning Brush
· 1 x Essential Oil Tube
· 1 x User Guide
· 1 x Thank You Card
3
How to Use
Caution
1. Please add water to the tank first, then add essential oils up to the
marking on the tube or until dispensing starts. If there's no
fragrance, the water-oil balance may be off. Please add enough
essential oil as instructed then.
1H 3H 6H ON
2. It is recommended to use purified or distilled water.
3. Cinnamon essential oil is of higher density and viscosity than that
of water. When adding the cinnamon essential oil to the water, it will
sink to the bottom. It is recommended that the essential oil be
added directly on the water surface to accelerate diffusion.
Add and Drain Water
1. Remove the tank cover, add water into the tank no higher than the
max water level. Add a few drops of essential oil into the tube
until it spills out slightly. Put the tank cover back on.
3. Clean the water tank with the included brush when grime builds up.
Note:
Never pour essential oils into the tube when there is no water inside
the tank.
2. Drain excess water via the drain side if necessary.
1H 3H 6H ON ⑦Timer Indicators
⑧Base
⑨Light Button
⑩Timer Button
⑪Power / Mist Button
⑫Power Port
1H 3H 6H ON
1H 3H 6H ON
1H 3H 6H ON 1H 3H 6H ON
Timer Setting:
When the unit is on, press to set 1 / 3 / 6 hours
timer. The corresponding indicator will light up.
Timer OFF:
When the timer is on, press and hold for 2
seconds to turn off the timer at any time.
Automatic Color Changing:
Press once to enter automatic color changing
mode where 7 colors will be cycled through.
Select Color:
Press again to stay on the current color. Keep
pressing to cycle through different colors.
Press and hold for 2 seconds to turn off the mist.
Switch between High & Low Mist:
Press again to resume High Mist. Switch
between the two modes with each press.
Low Mist:
Press again to enter low mist mode with one
beep sound.
High Mist:
Press once to enter the default high mist mode.
Two beeps will sound and the ON indicator will
light up.
Operations and Functions
Connect to a power source. Once connected,the diffuser will enter
standby mode. Please make sure there is enough water inside the tank.
OperationsFunctions
Mist ON
Mist OFF
Timer
Setting
Light Mode
Setting
Low Water Protection
The diffuser will turn off automatically when water inside the tank has
been depleted. Once water is added back into the tank, the diffuser
will resume standby mode.
How to Clean
IMPORTANT!
Please unplug the unit before cleaning!
Regular Cleaning
1) Empty the tank from the water outlet.
2) Add 3-5g (approx. one teaspoon, based on scale of the residues)
baking soda / NaHCO3 to the tank.
3) Fill the tank halfway full with warm water (200-250ml / 6.76-8.45fl
oz, 50°C / 122°F), stir it to fully dissolve.
4) Soak for 3-5mins, wipe down the tank and tank cover using a small
brush or soft cloth with baking soda solution. (For better cleaning,
remove the muting cover and wipe it down thoroughly).
5) Drain the solution and rinse the tank under tap water.
6) Rub the inside and outside dry with a dry towel or clean cloth.
7) Wipe off the soda residues if any.
Deep Cleaning
You are recommended to deep clean your diffuser once a month or
when the mist output is low due to grime build-up.
1) Empty the tank from the water outlet.
2) Add 2-3 teaspoons of baking soda / NaHCO3, or 2-3 slices of fresh
lemon to the tank.
3) Fill the tank halfway full with warm water (200-250ml / 6.76-8.45fl
oz, 50°C / 122°F), stir it to fully dissolve.
4) Soak for about half an hour.
5) Thoroughly clean the grime at the bottom and atomizer (slot at the
center) of the tank with a small brush.
6) Wipe down tank cover using a small brush or soft cloth with baking
soda solution. (For better cleaning, remove the muting cover and
wipe it down thoroughly).
7) Drain the solution and rinse the tank under tap water.
8) Wipe off the soda residues if any.
9) Rub the inside and outside dry with a dry towel or clean cloth.
Notes:
1) You may use dishwashing detergent when baking soda is
unavailable. But it works better for oil removing instead of odor
and mineral buildup.
2) Do not rinse the base directly with water; try to avoid wetting the
buttons, light holes, air inlets and underneath to avoid short circuit.
3) It is not recommended to clean the unit with white vinegar since
its direct and indirect contact with the atomizer will damage it
permanently.
Troubleshooting
No. Problem Solution
1
The LED light is not
turned on when powered
on.
Press the Light Button to turn
on the light.
2
The unit stops misting
with the light flashing
red as over-temperature
alarm.
• Turn off the unit.
• Pay attention to the
environmental temperature
and place the unit in a
well-ventilated place to cool
down.
• Do not add warm water into
the tank.
3The mist output is
becoming low.
• Keep the water clean or use
purified or distilled water.
• Clean the atomizer regularly.
4
Mist level is becoming
low, and finally stops
misting.
Add water if there is not
enough water in the water
tank.
5Scales in the water tank
and water reservoir
Clean the unit as instructed in
the Cleaning and Maintenance
section.
6Strange odor after long
idle time
Clean the unit thoroughly
before use.
No. Problem Solution
7
Previously used
essential oil smell
remains in the unit.
Clean the unit thoroughly
before use.
8 Diffusion not enough Turn on the High Mist mode.
9 Wet table surface
The mist level is too high for
the small space. Please lower
the mist level.
10 Fragrance not strong
enough
Add the essential oil into the
tube until it spills out slightly.
11
No fragrance after
adding cinnamon
essential oil
Cinnamon essential oil
is of higher density and
viscosity than that of water.
It is recommended that the
essential oil be added directly
on the water surface to
accelerate the diffusion.
12 Failed to select one
color
Press the Light Button once
to enter automatic color
changing mode. Press it
again to stay on the current
color. Keep pressing to cycle
through different colors.
ENEN
DE
Produktabbildung ⑦Timer
⑧Basis
⑨Lichttaste
⑩Tim e r-Ta s te
⑪Power- / Nebeltaste
⑫Stromanschluss
①Zerstäuberdüse
②Tankabdeckung
③Dämpfende Abdeckung
④Röhrchen für ätherische Öle
⑤Max. Wasserfüllstand
⑥Seitenablauf
1 2 3 4 5 6 7 8 9 10
AJ-PCN082
Input: 100-240V~ 50/60Hz
Output: DC 24V 0.5A
<10W
>5h (High Mist)
>8h (Low Mist)
60 ml / 2.0 fl. oz (High Mist)
30 ml / 1.0 fl. oz (Low Mist)
300 ml / 10.0 fl. oz
2.4MHz
Model: AJPCN082
Anjou Aroma Diffuser
User Guide
Product Diagram
1
2
6
4
8
910 11
12
5
7①Nozzle
②Tank Cover
③Muting Cover
④Essential Oil Tube
⑤Water Tank
⑥Drain Side
Specifications
Model
Power Adapter
Power
Working Time
Mist Output
Water Tank Volume
Ultrasonic Frequency
Package Contents
· 1 x Aroma Diffuser
· 1 x Power Adapter
· 1 x Cleaning Brush
· 1 x Essential Oil Tube
· 1 x User Guide
· 1 x Thank You Card
3
How to Use
Caution
1. Please add water to the tank first, then add essential oils up to the
marking on the tube or until dispensing starts. If there's no
fragrance, the water-oil balance may be off. Please add enough
essential oil as instructed then.
1H 3H 6H ON
2. It is recommended to use purified or distilled water.
3. Cinnamon essential oil is of higher density and viscosity than that
of water. When adding the cinnamon essential oil to the water, it will
sink to the bottom. It is recommended that the essential oil be
added directly on the water surface to accelerate diffusion.
Add and Drain Water
1. Remove the tank cover, add water into the tank no higher than the
max water level. Add a few drops of essential oil into the tube
until it spills out slightly. Put the tank cover back on.
3. Clean the water tank with the included brush when grime builds up.
Note:
Never pour essential oils into the tube when there is no water inside
the tank.
2. Drain excess water via the drain side if necessary.
1H 3H 6H ON ⑦Timer Indicators
⑧Base
⑨Light Button
⑩Timer Button
⑪Power / Mist Button
⑫Power Port
1H 3H 6H ON
1H 3H 6H ON
1H 3H 6H ON 1H 3H 6H ON
Timer Setting:
When the unit is on, press to set 1 / 3 / 6 hours
timer. The corresponding indicator will light up.
Timer OFF:
When the timer is on, press and hold for 2
seconds to turn off the timer at any time.
Automatic Color Changing:
Press once to enter automatic color changing
mode where 7 colors will be cycled through.
Select Color:
Press again to stay on the current color. Keep
pressing to cycle through different colors.
Press and hold for 2 seconds to turn off the mist.
Switch between High & Low Mist:
Press again to resume High Mist. Switch
between the two modes with each press.
Low Mist:
Press again to enter low mist mode with one
beep sound.
High Mist:
Press once to enter the default high mist mode.
Two beeps will sound and the ON indicator will
light up.
Operations and Functions
Connect to a power source. Once connected,the diffuser will enter
standby mode. Please make sure there is enough water inside the tank.
OperationsFunctions
Mist ON
Mist OFF
Timer
Setting
Light Mode
Setting
Low Water Protection
The diffuser will turn off automatically when water inside the tank has
been depleted. Once water is added back into the tank, the diffuser
will resume standby mode.
How to Clean
IMPORTANT!
Please unplug the unit before cleaning!
Regular Cleaning
1) Empty the tank from the water outlet.
2) Add 3-5g (approx. one teaspoon, based on scale of the residues)
baking soda / NaHCO3 to the tank.
3) Fill the tank halfway full with warm water (200-250ml / 6.76-8.45fl
oz, 50°C / 122°F), stir it to fully dissolve.
4) Soak for 3-5mins, wipe down the tank and tank cover using a small
brush or soft cloth with baking soda solution. (For better cleaning,
remove the muting cover and wipe it down thoroughly).
5) Drain the solution and rinse the tank under tap water.
6) Rub the inside and outside dry with a dry towel or clean cloth.
7) Wipe off the soda residues if any.
Deep Cleaning
You are recommended to deep clean your diffuser once a month or
when the mist output is low due to grime build-up.
1) Empty the tank from the water outlet.
2) Add 2-3 teaspoons of baking soda / NaHCO3, or 2-3 slices of fresh
lemon to the tank.
3) Fill the tank halfway full with warm water (200-250ml / 6.76-8.45fl
oz, 50°C / 122°F), stir it to fully dissolve.
4) Soak for about half an hour.
5) Thoroughly clean the grime at the bottom and atomizer (slot at the
center) of the tank with a small brush.
6) Wipe down tank cover using a small brush or soft cloth with baking
soda solution. (For better cleaning, remove the muting cover and
wipe it down thoroughly).
7) Drain the solution and rinse the tank under tap water.
8) Wipe off the soda residues if any.
9) Rub the inside and outside dry with a dry towel or clean cloth.
Notes:
1) You may use dishwashing detergent when baking soda is
unavailable. But it works better for oil removing instead of odor
and mineral buildup.
2) Do not rinse the base directly with water; try to avoid wetting the
buttons, light holes, air inlets and underneath to avoid short circuit.
3) It is not recommended to clean the unit with white vinegar since
its direct and indirect contact with the atomizer will damage it
permanently.
Troubleshooting
No. Problem Solution
1
The LED light is not
turned on when powered
on.
Press the Light Button to turn
on the light.
2
The unit stops misting
with the light flashing
red as over-temperature
alarm.
• Turn off the unit.
• Pay attention to the
environmental temperature
and place the unit in a
well-ventilated place to cool
down.
• Do not add warm water into
the tank.
3The mist output is
becoming low.
• Keep the water clean or use
purified or distilled water.
• Clean the atomizer regularly.
4
Mist level is becoming
low, and finally stops
misting.
Add water if there is not
enough water in the water
tank.
5Scales in the water tank
and water reservoir
Clean the unit as instructed in
the Cleaning and Maintenance
section.
6Strange odor after long
idle time
Clean the unit thoroughly
before use.
No. Problem Solution
7
Previously used
essential oil smell
remains in the unit.
Clean the unit thoroughly
before use.
8 Diffusion not enough Turn on the High Mist mode.
9 Wet table surface
The mist level is too high for
the small space. Please lower
the mist level.
10 Fragrance not strong
enough
Add the essential oil into the
tube until it spills out slightly.
11
No fragrance after
adding cinnamon
essential oil
Cinnamon essential oil
is of higher density and
viscosity than that of water.
It is recommended that the
essential oil be added directly
on the water surface to
accelerate the diffusion.
12 Failed to select one
color
Press the Light Button once
to enter automatic color
changing mode. Press it
again to stay on the current
color. Keep pressing to cycle
through different colors.
ENEN
DE
Produktabbildung ⑦Timer
⑧Basis
⑨Lichttaste
⑩Tim e r-Ta s te
⑪Power- / Nebeltaste
⑫Stromanschluss
①Zerstäuberdüse
②Tankabdeckung
③Dämpfende Abdeckung
④Röhrchen für ätherische Öle
⑤Max. Wasserfüllstand
⑥Seitenablauf
1 2 3 4 5 6 7 8 9 10
AJ-PCN082
Input: 100-240V~ 50/60Hz
Output: DC 24V 0.5A
<10W
>5h (High Mist)
>8h (Low Mist)
60 ml / 2.0 fl. oz (High Mist)
30 ml / 1.0 fl. oz (Low Mist)
300 ml / 10.0 fl. oz
2.4MHz
Model: AJPCN082
Anjou Aroma Diffuser
User Guide
Product Diagram
1
2
6
4
8
910 11
12
5
7①Nozzle
②Tank Cover
③Muting Cover
④Essential Oil Tube
⑤Water Tank
⑥Drain Side
Specifications
Model
Power Adapter
Power
Working Time
Mist Output
Water Tank Volume
Ultrasonic Frequency
Package Contents
· 1 x Aroma Diffuser
· 1 x Power Adapter
· 1 x Cleaning Brush
· 1 x Essential Oil Tube
· 1 x User Guide
· 1 x Thank You Card
3
How to Use
Caution
1. Please add water to the tank first, then add essential oils up to the
marking on the tube or until dispensing starts. If there's no
fragrance, the water-oil balance may be off. Please add enough
essential oil as instructed then.
1H 3H 6H ON
2. It is recommended to use purified or distilled water.
3. Cinnamon essential oil is of higher density and viscosity than that
of water. When adding the cinnamon essential oil to the water, it will
sink to the bottom. It is recommended that the essential oil be
added directly on the water surface to accelerate diffusion.
Add and Drain Water
1. Remove the tank cover, add water into the tank no higher than the
max water level. Add a few drops of essential oil into the tube
until it spills out slightly. Put the tank cover back on.
3. Clean the water tank with the included brush when grime builds up.
Note:
Never pour essential oils into the tube when there is no water inside
the tank.
2. Drain excess water via the drain side if necessary.
1H 3H 6H ON ⑦Timer Indicators
⑧Base
⑨Light Button
⑩Timer Button
⑪Power / Mist Button
⑫Power Port
1H 3H 6H ON
1H 3H 6H ON
1H 3H 6H ON 1H 3H 6H ON
Timer Setting:
When the unit is on, press to set 1 / 3 / 6 hours
timer. The corresponding indicator will light up.
Timer OFF:
When the timer is on, press and hold for 2
seconds to turn off the timer at any time.
Automatic Color Changing:
Press once to enter automatic color changing
mode where 7 colors will be cycled through.
Select Color:
Press again to stay on the current color. Keep
pressing to cycle through different colors.
Press and hold for 2 seconds to turn off the mist.
Switch between High & Low Mist:
Press again to resume High Mist. Switch
between the two modes with each press.
Low Mist:
Press again to enter low mist mode with one
beep sound.
High Mist:
Press once to enter the default high mist mode.
Two beeps will sound and the ON indicator will
light up.
Operations and Functions
Connect to a power source. Once connected,the diffuser will enter
standby mode. Please make sure there is enough water inside the tank.
OperationsFunctions
Mist ON
Mist OFF
Timer
Setting
Light Mode
Setting
Low Water Protection
The diffuser will turn off automatically when water inside the tank has
been depleted. Once water is added back into the tank, the diffuser
will resume standby mode.
How to Clean
IMPORTANT!
Please unplug the unit before cleaning!
Regular Cleaning
1) Empty the tank from the water outlet.
2) Add 3-5g (approx. one teaspoon, based on scale of the residues)
baking soda / NaHCO3 to the tank.
3) Fill the tank halfway full with warm water (200-250ml / 6.76-8.45fl
oz, 50°C / 122°F), stir it to fully dissolve.
4) Soak for 3-5mins, wipe down the tank and tank cover using a small
brush or soft cloth with baking soda solution. (For better cleaning,
remove the muting cover and wipe it down thoroughly).
5) Drain the solution and rinse the tank under tap water.
6) Rub the inside and outside dry with a dry towel or clean cloth.
7) Wipe off the soda residues if any.
Deep Cleaning
You are recommended to deep clean your diffuser once a month or
when the mist output is low due to grime build-up.
1) Empty the tank from the water outlet.
2) Add 2-3 teaspoons of baking soda / NaHCO3, or 2-3 slices of fresh
lemon to the tank.
3) Fill the tank halfway full with warm water (200-250ml / 6.76-8.45fl
oz, 50°C / 122°F), stir it to fully dissolve.
4) Soak for about half an hour.
5) Thoroughly clean the grime at the bottom and atomizer (slot at the
center) of the tank with a small brush.
6) Wipe down tank cover using a small brush or soft cloth with baking
soda solution. (For better cleaning, remove the muting cover and
wipe it down thoroughly).
7) Drain the solution and rinse the tank under tap water.
8) Wipe off the soda residues if any.
9) Rub the inside and outside dry with a dry towel or clean cloth.
Notes:
1) You may use dishwashing detergent when baking soda is
unavailable. But it works better for oil removing instead of odor
and mineral buildup.
2) Do not rinse the base directly with water; try to avoid wetting the
buttons, light holes, air inlets and underneath to avoid short circuit.
3) It is not recommended to clean the unit with white vinegar since
its direct and indirect contact with the atomizer will damage it
permanently.
Troubleshooting
No. Problem Solution
1
The LED light is not
turned on when powered
on.
Press the Light Button to turn
on the light.
2
The unit stops misting
with the light flashing
red as over-temperature
alarm.
• Turn off the unit.
• Pay attention to the
environmental temperature
and place the unit in a
well-ventilated place to cool
down.
• Do not add warm water into
the tank.
3The mist output is
becoming low.
• Keep the water clean or use
purified or distilled water.
• Clean the atomizer regularly.
4
Mist level is becoming
low, and finally stops
misting.
Add water if there is not
enough water in the water
tank.
5Scales in the water tank
and water reservoir
Clean the unit as instructed in
the Cleaning and Maintenance
section.
6Strange odor after long
idle time
Clean the unit thoroughly
before use.
No. Problem Solution
7
Previously used
essential oil smell
remains in the unit.
Clean the unit thoroughly
before use.
8 Diffusion not enough Turn on the High Mist mode.
9 Wet table surface
The mist level is too high for
the small space. Please lower
the mist level.
10 Fragrance not strong
enough
Add the essential oil into the
tube until it spills out slightly.
11
No fragrance after
adding cinnamon
essential oil
Cinnamon essential oil
is of higher density and
viscosity than that of water.
It is recommended that the
essential oil be added directly
on the water surface to
accelerate the diffusion.
12 Failed to select one
color
Press the Light Button once
to enter automatic color
changing mode. Press it
again to stay on the current
color. Keep pressing to cycle
through different colors.
ENEN
DE
Produktabbildung ⑦Timer
⑧Basis
⑨Lichttaste
⑩Tim e r-Ta s te
⑪Power- / Nebeltaste
⑫Stromanschluss
①Zerstäuberdüse
②Tankabdeckung
③Dämpfende Abdeckung
④Röhrchen für ätherische Öle
⑤Max. Wasserfüllstand
⑥Seitenablauf
1 2 3 4 5 6 7 8 9 10
AJ-PCN082
Input: 100-240V~ 50/60Hz
Output: DC 24V 0.5A
<10W
>5h (High Mist)
>8h (Low Mist)
60 ml / 2.0 fl. oz (High Mist)
30 ml / 1.0 fl. oz (Low Mist)
300 ml / 10.0 fl. oz
2.4MHz
Model: AJPCN082
Anjou Aroma Diffuser
User Guide
Product Diagram
1
2
6
4
8
910 11
12
5
7①Nozzle
②Tank Cover
③Muting Cover
④Essential Oil Tube
⑤Water Tank
⑥Drain Side
Specifications
Model
Power Adapter
Power
Working Time
Mist Output
Water Tank Volume
Ultrasonic Frequency
Package Contents
· 1 x Aroma Diffuser
· 1 x Power Adapter
· 1 x Cleaning Brush
· 1 x Essential Oil Tube
· 1 x User Guide
· 1 x Thank You Card
3
How to Use
Caution
1. Please add water to the tank first, then add essential oils up to the
marking on the tube or until dispensing starts. If there's no
fragrance, the water-oil balance may be off. Please add enough
essential oil as instructed then.
1H 3H 6H ON
2. It is recommended to use purified or distilled water.
3. Cinnamon essential oil is of higher density and viscosity than that
of water. When adding the cinnamon essential oil to the water, it will
sink to the bottom. It is recommended that the essential oil be
added directly on the water surface to accelerate diffusion.
Add and Drain Water
1. Remove the tank cover, add water into the tank no higher than the
max water level. Add a few drops of essential oil into the tube
until it spills out slightly. Put the tank cover back on.
3. Clean the water tank with the included brush when grime builds up.
Note:
Never pour essential oils into the tube when there is no water inside
the tank.
2. Drain excess water via the drain side if necessary.
1H 3H 6H ON ⑦Timer Indicators
⑧Base
⑨Light Button
⑩Timer Button
⑪Power / Mist Button
⑫Power Port
1H 3H 6H ON
1H 3H 6H ON
1H 3H 6H ON 1H 3H 6H ON
Timer Setting:
When the unit is on, press to set 1 / 3 / 6 hours
timer. The corresponding indicator will light up.
Timer OFF:
When the timer is on, press and hold for 2
seconds to turn off the timer at any time.
Automatic Color Changing:
Press once to enter automatic color changing
mode where 7 colors will be cycled through.
Select Color:
Press again to stay on the current color. Keep
pressing to cycle through different colors.
Press and hold for 2 seconds to turn off the mist.
Switch between High & Low Mist:
Press again to resume High Mist. Switch
between the two modes with each press.
Low Mist:
Press again to enter low mist mode with one
beep sound.
High Mist:
Press once to enter the default high mist mode.
Two beeps will sound and the ON indicator will
light up.
Operations and Functions
Connect to a power source. Once connected,the diffuser will enter
standby mode. Please make sure there is enough water inside the tank.
OperationsFunctions
Mist ON
Mist OFF
Timer
Setting
Light Mode
Setting
Low Water Protection
The diffuser will turn off automatically when water inside the tank has
been depleted. Once water is added back into the tank, the diffuser
will resume standby mode.
How to Clean
IMPORTANT!
Please unplug the unit before cleaning!
Regular Cleaning
1) Empty the tank from the water outlet.
2) Add 3-5g (approx. one teaspoon, based on scale of the residues)
baking soda / NaHCO3 to the tank.
3) Fill the tank halfway full with warm water (200-250ml / 6.76-8.45fl
oz, 50°C / 122°F), stir it to fully dissolve.
4) Soak for 3-5mins, wipe down the tank and tank cover using a small
brush or soft cloth with baking soda solution. (For better cleaning,
remove the muting cover and wipe it down thoroughly).
5) Drain the solution and rinse the tank under tap water.
6) Rub the inside and outside dry with a dry towel or clean cloth.
7) Wipe off the soda residues if any.
Deep Cleaning
You are recommended to deep clean your diffuser once a month or
when the mist output is low due to grime build-up.
1) Empty the tank from the water outlet.
2) Add 2-3 teaspoons of baking soda / NaHCO3, or 2-3 slices of fresh
lemon to the tank.
3) Fill the tank halfway full with warm water (200-250ml / 6.76-8.45fl
oz, 50°C / 122°F), stir it to fully dissolve.
4) Soak for about half an hour.
5) Thoroughly clean the grime at the bottom and atomizer (slot at the
center) of the tank with a small brush.
6) Wipe down tank cover using a small brush or soft cloth with baking
soda solution. (For better cleaning, remove the muting cover and
wipe it down thoroughly).
7) Drain the solution and rinse the tank under tap water.
8) Wipe off the soda residues if any.
9) Rub the inside and outside dry with a dry towel or clean cloth.
Notes:
1) You may use dishwashing detergent when baking soda is
unavailable. But it works better for oil removing instead of odor
and mineral buildup.
2) Do not rinse the base directly with water; try to avoid wetting the
buttons, light holes, air inlets and underneath to avoid short circuit.
3) It is not recommended to clean the unit with white vinegar since
its direct and indirect contact with the atomizer will damage it
permanently.
Troubleshooting
No. Problem Solution
1
The LED light is not
turned on when powered
on.
Press the Light Button to turn
on the light.
2
The unit stops misting
with the light flashing
red as over-temperature
alarm.
• Turn off the unit.
• Pay attention to the
environmental temperature
and place the unit in a
well-ventilated place to cool
down.
• Do not add warm water into
the tank.
3The mist output is
becoming low.
• Keep the water clean or use
purified or distilled water.
• Clean the atomizer regularly.
4
Mist level is becoming
low, and finally stops
misting.
Add water if there is not
enough water in the water
tank.
5Scales in the water tank
and water reservoir
Clean the unit as instructed in
the Cleaning and Maintenance
section.
6Strange odor after long
idle time
Clean the unit thoroughly
before use.
No. Problem Solution
7
Previously used
essential oil smell
remains in the unit.
Clean the unit thoroughly
before use.
8 Diffusion not enough Turn on the High Mist mode.
9 Wet table surface
The mist level is too high for
the small space. Please lower
the mist level.
10 Fragrance not strong
enough
Add the essential oil into the
tube until it spills out slightly.
11
No fragrance after
adding cinnamon
essential oil
Cinnamon essential oil
is of higher density and
viscosity than that of water.
It is recommended that the
essential oil be added directly
on the water surface to
accelerate the diffusion.
12 Failed to select one
color
Press the Light Button once
to enter automatic color
changing mode. Press it
again to stay on the current
color. Keep pressing to cycle
through different colors.
ENEN
DE
Produktabbildung ⑦Timer
⑧Basis
⑨Lichttaste
⑩Tim e r-Ta s te
⑪Power- / Nebeltaste
⑫Stromanschluss
①Zerstäuberdüse
②Tankabdeckung
③Dämpfende Abdeckung
④Röhrchen für ätherische Öle
⑤Max. Wasserfüllstand
⑥Seitenablauf
1 2 3 4 5 6 7 8 9 10
AJ-PCN082
Input: 100-240V~ 50/60Hz
Output: DC 24V 0.5A
<10W
>5h (High Mist)
>8h (Low Mist)
60 ml / 2.0 fl. oz (High Mist)
30 ml / 1.0 fl. oz (Low Mist)
300 ml / 10.0 fl. oz
2.4MHz
Model: AJPCN082
Anjou Aroma Diffuser
User Guide
Product Diagram
1
2
6
4
8
910 11
12
5
7①Nozzle
②Tank Cover
③Muting Cover
④Essential Oil Tube
⑤Water Tank
⑥Drain Side
Specifications
Model
Power Adapter
Power
Working Time
Mist Output
Water Tank Volume
Ultrasonic Frequency
Package Contents
· 1 x Aroma Diffuser
· 1 x Power Adapter
· 1 x Cleaning Brush
· 1 x Essential Oil Tube
· 1 x User Guide
· 1 x Thank You Card
3
How to Use
Caution
1. Please add water to the tank first, then add essential oils up to the
marking on the tube or until dispensing starts. If there's no
fragrance, the water-oil balance may be off. Please add enough
essential oil as instructed then.
1H 3H 6H ON
2. It is recommended to use purified or distilled water.
3. Cinnamon essential oil is of higher density and viscosity than that
of water. When adding the cinnamon essential oil to the water, it will
sink to the bottom. It is recommended that the essential oil be
added directly on the water surface to accelerate diffusion.
Add and Drain Water
1. Remove the tank cover, add water into the tank no higher than the
max water level. Add a few drops of essential oil into the tube
until it spills out slightly. Put the tank cover back on.
3. Clean the water tank with the included brush when grime builds up.
Note:
Never pour essential oils into the tube when there is no water inside
the tank.
2. Drain excess water via the drain side if necessary.
1H 3H 6H ON ⑦Timer Indicators
⑧Base
⑨Light Button
⑩Timer Button
⑪Power / Mist Button
⑫Power Port
1H 3H 6H ON
1H 3H 6H ON
1H 3H 6H ON 1H 3H 6H ON
Timer Setting:
When the unit is on, press to set 1 / 3 / 6 hours
timer. The corresponding indicator will light up.
Timer OFF:
When the timer is on, press and hold for 2
seconds to turn off the timer at any time.
Automatic Color Changing:
Press once to enter automatic color changing
mode where 7 colors will be cycled through.
Select Color:
Press again to stay on the current color. Keep
pressing to cycle through different colors.
Press and hold for 2 seconds to turn off the mist.
Switch between High & Low Mist:
Press again to resume High Mist. Switch
between the two modes with each press.
Low Mist:
Press again to enter low mist mode with one
beep sound.
High Mist:
Press once to enter the default high mist mode.
Two beeps will sound and the ON indicator will
light up.
Operations and Functions
Connect to a power source. Once connected,the diffuser will enter
standby mode. Please make sure there is enough water inside the tank.
OperationsFunctions
Mist ON
Mist OFF
Timer
Setting
Light Mode
Setting
Low Water Protection
The diffuser will turn off automatically when water inside the tank has
been depleted. Once water is added back into the tank, the diffuser
will resume standby mode.
How to Clean
IMPORTANT!
Please unplug the unit before cleaning!
Regular Cleaning
1) Empty the tank from the water outlet.
2) Add 3-5g (approx. one teaspoon, based on scale of the residues)
baking soda / NaHCO3 to the tank.
3) Fill the tank halfway full with warm water (200-250ml / 6.76-8.45fl
oz, 50°C / 122°F), stir it to fully dissolve.
4) Soak for 3-5mins, wipe down the tank and tank cover using a small
brush or soft cloth with baking soda solution. (For better cleaning,
remove the muting cover and wipe it down thoroughly).
5) Drain the solution and rinse the tank under tap water.
6) Rub the inside and outside dry with a dry towel or clean cloth.
7) Wipe off the soda residues if any.
Deep Cleaning
You are recommended to deep clean your diffuser once a month or
when the mist output is low due to grime build-up.
1) Empty the tank from the water outlet.
2) Add 2-3 teaspoons of baking soda / NaHCO3, or 2-3 slices of fresh
lemon to the tank.
3) Fill the tank halfway full with warm water (200-250ml / 6.76-8.45fl
oz, 50°C / 122°F), stir it to fully dissolve.
4) Soak for about half an hour.
5) Thoroughly clean the grime at the bottom and atomizer (slot at the
center) of the tank with a small brush.
6) Wipe down tank cover using a small brush or soft cloth with baking
soda solution. (For better cleaning, remove the muting cover and
wipe it down thoroughly).
7) Drain the solution and rinse the tank under tap water.
8) Wipe off the soda residues if any.
9) Rub the inside and outside dry with a dry towel or clean cloth.
Notes:
1) You may use dishwashing detergent when baking soda is
unavailable. But it works better for oil removing instead of odor
and mineral buildup.
2) Do not rinse the base directly with water; try to avoid wetting the
buttons, light holes, air inlets and underneath to avoid short circuit.
3) It is not recommended to clean the unit with white vinegar since
its direct and indirect contact with the atomizer will damage it
permanently.
Troubleshooting
No. Problem Solution
1
The LED light is not
turned on when powered
on.
Press the Light Button to turn
on the light.
2
The unit stops misting
with the light flashing
red as over-temperature
alarm.
• Turn off the unit.
• Pay attention to the
environmental temperature
and place the unit in a
well-ventilated place to cool
down.
• Do not add warm water into
the tank.
3The mist output is
becoming low.
• Keep the water clean or use
purified or distilled water.
• Clean the atomizer regularly.
4
Mist level is becoming
low, and finally stops
misting.
Add water if there is not
enough water in the water
tank.
5Scales in the water tank
and water reservoir
Clean the unit as instructed in
the Cleaning and Maintenance
section.
6Strange odor after long
idle time
Clean the unit thoroughly
before use.
No. Problem Solution
7
Previously used
essential oil smell
remains in the unit.
Clean the unit thoroughly
before use.
8 Diffusion not enough Turn on the High Mist mode.
9 Wet table surface
The mist level is too high for
the small space. Please lower
the mist level.
10 Fragrance not strong
enough
Add the essential oil into the
tube until it spills out slightly.
11
No fragrance after
adding cinnamon
essential oil
Cinnamon essential oil
is of higher density and
viscosity than that of water.
It is recommended that the
essential oil be added directly
on the water surface to
accelerate the diffusion.
12 Failed to select one
color
Press the Light Button once
to enter automatic color
changing mode. Press it
again to stay on the current
color. Keep pressing to cycle
through different colors.
ENEN
DE
Produktabbildung ⑦Timer
⑧Basis
⑨Lichttaste
⑩Tim e r-Ta s te
⑪Power- / Nebeltaste
⑫Stromanschluss
①Zerstäuberdüse
②Tankabdeckung
③Dämpfende Abdeckung
④Röhrchen für ätherische Öle
⑤Max. Wasserfüllstand
⑥Seitenablauf
1 2 3 4 5 6 7 8 9 10
AJ-PCN082
Input: 100-240V~ 50/60Hz
Output: DC 24V 0.5A
<10W
>5h (High Mist)
>8h (Low Mist)
60 ml / 2.0 fl. oz (High Mist)
30 ml / 1.0 fl. oz (Low Mist)
300 ml / 10.0 fl. oz
2.4MHz
Model: AJPCN082
Anjou Aroma Diffuser
User Guide
Product Diagram
1
2
6
4
8
910 11
12
5
7①Nozzle
②Tank Cover
③Muting Cover
④Essential Oil Tube
⑤Water Tank
⑥Drain Side
Specifications
Model
Power Adapter
Power
Working Time
Mist Output
Water Tank Volume
Ultrasonic Frequency
Package Contents
· 1 x Aroma Diffuser
· 1 x Power Adapter
· 1 x Cleaning Brush
· 1 x Essential Oil Tube
· 1 x User Guide
· 1 x Thank You Card
3
How to Use
Caution
1. Please add water to the tank first, then add essential oils up to the
marking on the tube or until dispensing starts. If there's no
fragrance, the water-oil balance may be off. Please add enough
essential oil as instructed then.
1H 3H 6H ON
2. It is recommended to use purified or distilled water.
3. Cinnamon essential oil is of higher density and viscosity than that
of water. When adding the cinnamon essential oil to the water, it will
sink to the bottom. It is recommended that the essential oil be
added directly on the water surface to accelerate diffusion.
Add and Drain Water
1. Remove the tank cover, add water into the tank no higher than the
max water level. Add a few drops of essential oil into the tube
until it spills out slightly. Put the tank cover back on.
3. Clean the water tank with the included brush when grime builds up.
Note:
Never pour essential oils into the tube when there is no water inside
the tank.
2. Drain excess water via the drain side if necessary.
1H 3H 6H ON ⑦Timer Indicators
⑧Base
⑨Light Button
⑩Timer Button
⑪Power / Mist Button
⑫Power Port
1H 3H 6H ON
1H 3H 6H ON
1H 3H 6H ON 1H 3H 6H ON
Timer Setting:
When the unit is on, press to set 1 / 3 / 6 hours
timer. The corresponding indicator will light up.
Timer OFF:
When the timer is on, press and hold for 2
seconds to turn off the timer at any time.
Automatic Color Changing:
Press once to enter automatic color changing
mode where 7 colors will be cycled through.
Select Color:
Press again to stay on the current color. Keep
pressing to cycle through different colors.
Press and hold for 2 seconds to turn off the mist.
Switch between High & Low Mist:
Press again to resume High Mist. Switch
between the two modes with each press.
Low Mist:
Press again to enter low mist mode with one
beep sound.
High Mist:
Press once to enter the default high mist mode.
Two beeps will sound and the ON indicator will
light up.
Operations and Functions
Connect to a power source. Once connected,the diffuser will enter
standby mode. Please make sure there is enough water inside the tank.
OperationsFunctions
Mist ON
Mist OFF
Timer
Setting
Light Mode
Setting
Low Water Protection
The diffuser will turn off automatically when water inside the tank has
been depleted. Once water is added back into the tank, the diffuser
will resume standby mode.
How to Clean
IMPORTANT!
Please unplug the unit before cleaning!
Regular Cleaning
1) Empty the tank from the water outlet.
2) Add 3-5g (approx. one teaspoon, based on scale of the residues)
baking soda / NaHCO3 to the tank.
3) Fill the tank halfway full with warm water (200-250ml / 6.76-8.45fl
oz, 50°C / 122°F), stir it to fully dissolve.
4) Soak for 3-5mins, wipe down the tank and tank cover using a small
brush or soft cloth with baking soda solution. (For better cleaning,
remove the muting cover and wipe it down thoroughly).
5) Drain the solution and rinse the tank under tap water.
6) Rub the inside and outside dry with a dry towel or clean cloth.
7) Wipe off the soda residues if any.
Deep Cleaning
You are recommended to deep clean your diffuser once a month or
when the mist output is low due to grime build-up.
1) Empty the tank from the water outlet.
2) Add 2-3 teaspoons of baking soda / NaHCO3, or 2-3 slices of fresh
lemon to the tank.
3) Fill the tank halfway full with warm water (200-250ml / 6.76-8.45fl
oz, 50°C / 122°F), stir it to fully dissolve.
4) Soak for about half an hour.
5) Thoroughly clean the grime at the bottom and atomizer (slot at the
center) of the tank with a small brush.
6) Wipe down tank cover using a small brush or soft cloth with baking
soda solution. (For better cleaning, remove the muting cover and
wipe it down thoroughly).
7) Drain the solution and rinse the tank under tap water.
8) Wipe off the soda residues if any.
9) Rub the inside and outside dry with a dry towel or clean cloth.
Notes:
1) You may use dishwashing detergent when baking soda is
unavailable. But it works better for oil removing instead of odor
and mineral buildup.
2) Do not rinse the base directly with water; try to avoid wetting the
buttons, light holes, air inlets and underneath to avoid short circuit.
3) It is not recommended to clean the unit with white vinegar since
its direct and indirect contact with the atomizer will damage it
permanently.
Troubleshooting
No. Problem Solution
1
The LED light is not
turned on when powered
on.
Press the Light Button to turn
on the light.
2
The unit stops misting
with the light flashing
red as over-temperature
alarm.
• Turn off the unit.
• Pay attention to the
environmental temperature
and place the unit in a
well-ventilated place to cool
down.
• Do not add warm water into
the tank.
3The mist output is
becoming low.
• Keep the water clean or use
purified or distilled water.
• Clean the atomizer regularly.
4
Mist level is becoming
low, and finally stops
misting.
Add water if there is not
enough water in the water
tank.
5Scales in the water tank
and water reservoir
Clean the unit as instructed in
the Cleaning and Maintenance
section.
6Strange odor after long
idle time
Clean the unit thoroughly
before use.
No. Problem Solution
7
Previously used
essential oil smell
remains in the unit.
Clean the unit thoroughly
before use.
8 Diffusion not enough Turn on the High Mist mode.
9 Wet table surface
The mist level is too high for
the small space. Please lower
the mist level.
10 Fragrance not strong
enough
Add the essential oil into the
tube until it spills out slightly.
11
No fragrance after
adding cinnamon
essential oil
Cinnamon essential oil
is of higher density and
viscosity than that of water.
It is recommended that the
essential oil be added directly
on the water surface to
accelerate the diffusion.
12 Failed to select one
color
Press the Light Button once
to enter automatic color
changing mode. Press it
again to stay on the current
color. Keep pressing to cycle
through different colors.
ENEN
DE
Produktabbildung ⑦Timer
⑧Basis
⑨Lichttaste
⑩Tim e r-Ta s te
⑪Power- / Nebeltaste
⑫Stromanschluss
①Zerstäuberdüse
②Tankabdeckung
③Dämpfende Abdeckung
④Röhrchen für ätherische Öle
⑤Max. Wasserfüllstand
⑥Seitenablauf
1 2 3 4 5 6 7 8 9 10
AJ-PCN082
Input: 100-240V~ 50/60Hz
Output: DC 24V 0.5A
<10W
>5h (High Mist)
>8h (Low Mist)
60 ml / 2.0 fl. oz (High Mist)
30 ml / 1.0 fl. oz (Low Mist)
300 ml / 10.0 fl. oz
2.4MHz
Model: AJPCN082
Anjou Aroma Diffuser
User Guide
Product Diagram
1
2
6
4
8
910 11
12
5
7①Nozzle
②Tank Cover
③Muting Cover
④Essential Oil Tube
⑤Water Tank
⑥Drain Side
Specifications
Model
Power Adapter
Power
Working Time
Mist Output
Water Tank Volume
Ultrasonic Frequency
Package Contents
· 1 x Aroma Diffuser
· 1 x Power Adapter
· 1 x Cleaning Brush
· 1 x Essential Oil Tube
· 1 x User Guide
· 1 x Thank You Card
3
How to Use
Caution
1. Please add water to the tank first, then add essential oils up to the
marking on the tube or until dispensing starts. If there's no
fragrance, the water-oil balance may be off. Please add enough
essential oil as instructed then.
1H 3H 6H ON
2. It is recommended to use purified or distilled water.
3. Cinnamon essential oil is of higher density and viscosity than that
of water. When adding the cinnamon essential oil to the water, it will
sink to the bottom. It is recommended that the essential oil be
added directly on the water surface to accelerate diffusion.
Add and Drain Water
1. Remove the tank cover, add water into the tank no higher than the
max water level. Add a few drops of essential oil into the tube
until it spills out slightly. Put the tank cover back on.
3. Clean the water tank with the included brush when grime builds up.
Note:
Never pour essential oils into the tube when there is no water inside
the tank.
2. Drain excess water via the drain side if necessary.
1H 3H 6H ON ⑦Timer Indicators
⑧Base
⑨Light Button
⑩Timer Button
⑪Power / Mist Button
⑫Power Port
1H 3H 6H ON
1H 3H 6H ON
1H 3H 6H ON 1H 3H 6H ON
Timer Setting:
When the unit is on, press to set 1 / 3 / 6 hours
timer. The corresponding indicator will light up.
Timer OFF:
When the timer is on, press and hold for 2
seconds to turn off the timer at any time.
Automatic Color Changing:
Press once to enter automatic color changing
mode where 7 colors will be cycled through.
Select Color:
Press again to stay on the current color. Keep
pressing to cycle through different colors.
Press and hold for 2 seconds to turn off the mist.
Switch between High & Low Mist:
Press again to resume High Mist. Switch
between the two modes with each press.
Low Mist:
Press again to enter low mist mode with one
beep sound.
High Mist:
Press once to enter the default high mist mode.
Two beeps will sound and the ON indicator will
light up.
Operations and Functions
Connect to a power source. Once connected,the diffuser will enter
standby mode. Please make sure there is enough water inside the tank.
OperationsFunctions
Mist ON
Mist OFF
Timer
Setting
Light Mode
Setting
Low Water Protection
The diffuser will turn off automatically when water inside the tank has
been depleted. Once water is added back into the tank, the diffuser
will resume standby mode.
How to Clean
IMPORTANT!
Please unplug the unit before cleaning!
Regular Cleaning
1) Empty the tank from the water outlet.
2) Add 3-5g (approx. one teaspoon, based on scale of the residues)
baking soda / NaHCO3 to the tank.
3) Fill the tank halfway full with warm water (200-250ml / 6.76-8.45fl
oz, 50°C / 122°F), stir it to fully dissolve.
4) Soak for 3-5mins, wipe down the tank and tank cover using a small
brush or soft cloth with baking soda solution. (For better cleaning,
remove the muting cover and wipe it down thoroughly).
5) Drain the solution and rinse the tank under tap water.
6) Rub the inside and outside dry with a dry towel or clean cloth.
7) Wipe off the soda residues if any.
Deep Cleaning
You are recommended to deep clean your diffuser once a month or
when the mist output is low due to grime build-up.
1) Empty the tank from the water outlet.
2) Add 2-3 teaspoons of baking soda / NaHCO3, or 2-3 slices of fresh
lemon to the tank.
3) Fill the tank halfway full with warm water (200-250ml / 6.76-8.45fl
oz, 50°C / 122°F), stir it to fully dissolve.
4) Soak for about half an hour.
5) Thoroughly clean the grime at the bottom and atomizer (slot at the
center) of the tank with a small brush.
6) Wipe down tank cover using a small brush or soft cloth with baking
soda solution. (For better cleaning, remove the muting cover and
wipe it down thoroughly).
7) Drain the solution and rinse the tank under tap water.
8) Wipe off the soda residues if any.
9) Rub the inside and outside dry with a dry towel or clean cloth.
Notes:
1) You may use dishwashing detergent when baking soda is
unavailable. But it works better for oil removing instead of odor
and mineral buildup.
2) Do not rinse the base directly with water; try to avoid wetting the
buttons, light holes, air inlets and underneath to avoid short circuit.
3) It is not recommended to clean the unit with white vinegar since
its direct and indirect contact with the atomizer will damage it
permanently.
Troubleshooting
No. Problem Solution
1
The LED light is not
turned on when powered
on.
Press the Light Button to turn
on the light.
2
The unit stops misting
with the light flashing
red as over-temperature
alarm.
• Turn off the unit.
• Pay attention to the
environmental temperature
and place the unit in a
well-ventilated place to cool
down.
• Do not add warm water into
the tank.
3The mist output is
becoming low.
• Keep the water clean or use
purified or distilled water.
• Clean the atomizer regularly.
4
Mist level is becoming
low, and finally stops
misting.
Add water if there is not
enough water in the water
tank.
5Scales in the water tank
and water reservoir
Clean the unit as instructed in
the Cleaning and Maintenance
section.
6Strange odor after long
idle time
Clean the unit thoroughly
before use.
No. Problem Solution
7
Previously used
essential oil smell
remains in the unit.
Clean the unit thoroughly
before use.
8 Diffusion not enough Turn on the High Mist mode.
9 Wet table surface
The mist level is too high for
the small space. Please lower
the mist level.
10 Fragrance not strong
enough
Add the essential oil into the
tube until it spills out slightly.
11
No fragrance after
adding cinnamon
essential oil
Cinnamon essential oil
is of higher density and
viscosity than that of water.
It is recommended that the
essential oil be added directly
on the water surface to
accelerate the diffusion.
12 Failed to select one
color
Press the Light Button once
to enter automatic color
changing mode. Press it
again to stay on the current
color. Keep pressing to cycle
through different colors.
ENEN
DE
Produktabbildung ⑦Timer
⑧Basis
⑨Lichttaste
⑩Tim e r-Ta s te
⑪Power- / Nebeltaste
⑫Stromanschluss
①Zerstäuberdüse
②Tankabdeckung
③Dämpfende Abdeckung
④Röhrchen für ätherische Öle
⑤Max. Wasserfüllstand
⑥Seitenablauf
1 2 3 4 5 6 7 8 9 10
AJ-PCN082
Eingang: 100-240V~ 50/60Hz
Ausgang: DC 24V 0.5A
＜10W
＞5h (Starker Nebel))
＞8h (Geringer Nebel)
60 ml / 2.0 fl. oz (Starker Nebel)
30 ml / 1.0 fl. oz (Geringer Nebel)
300 ml / 10.0 fl. oz
2.4MHz
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
WEEE Compliance
Correct Disposal of This Product (Waste Electrical & Electronic
Equipment) (Applicable in countries with separate collection systems)
This marking on the product, accessories or literature indicates that
the product and its electronic accessories should not be disposed of
with other household waste at the end of their working life. To prevent
possible harm to the environment or human health from uncontrolled
waste disposal, please separate these items from other types of
waste and recycle them responsibly to promote the sustainable reuse
of material resources. Household users should contact either the
retailer where they purchased this product, or their local government
office, for details of where and how they can take these items for
environmentally safe recycling. Business users should contact their
supplier and check the terms and conditions of the purchase
contract. This product and its electronic accessories should not be
mixed with other commercial wastes for disposal.
MADE IN CHINA
DE
Spezifikationen
Modell
Netzteil
Leistung
Betriebszeit
Nebelausstoß
Wassertank-Volumen
Ultraschallfrequenz
Im Lieferumfang enthalten
· 1 x Aroma-Diffuser
· 1 x Netzstecker
· 1 x Reinigungsbürste
· 1 x Bedienungsanleitung
· 1 x Dankeschön-Karte
· 1 x Tubus für Ätherische Öle
Bedienung
Achtung
1. Bitte geben Sie zunächst Wasser in den Tank, fügen Sie dann bis zur
Markierung am. Rohr oder bis zu Beginn der Ausgabe ätherisches Öl
hinein. Falls kein Duft wahrnehmbar ist, ist möglicherweise die
Wasser-Öl-Balance falsch. Bitte geben Sie genügend ätherisches Öl
entsprechend den Anweisungen hinein.
1H 3H 6H ON
2. Es wird empfohlen, gereinigtes oder destilliertes Wasser zu verwenden.
3. Ätherisches Zimtöl verfügt über eine höhere Dichte und Viskosität
als Wasser. Wenn Sie ätherisches Zimtöl ins Wasser geben, sinkt es
auf den Boden. Wir empfehlen, ätherisches Öl direkt auf die
Wasseroberfläche zu geben, um die Diffusion zu beschleunigen.
Einfüllen und Abgießen von Wasser
1. Nehmen Sie die Tankabdeckung ab und befüllen Sie den Tank bis
maximal zur max. Wasserstandslinie mit Wasser. Einige Tropfen
ätherisches Öl in das Rohr geben, bis die Ausgabe beginnt. Setzen
Sie die Tankabdeckung wieder auf.
2. Falls nötig, lassen Sie überschüssiges Wasser über den Seitenab
lauf abfließen.
3. Reinigen Sie den Wassertank mit der mitgelieferten Bürste, wenn
sich Ablagerungen bilden.
Anmerkung:
Gießen Sie nie ätherisches Öl ins Röhrchen, wenn kein Wasser im Tank ist.
1H 3H 6H ON 1H 3H 6H ON
1H 3H 6H ON
1H 3H 6H ON
Starke Vernebelung:
Drücken Sie einmal, um den standardmäßigen
starken Vernebelungsmodus zu aktivieren. Es erklingen
zwei Pieptöne und die ON-Anzeige leuchtet auf.
Geringe Vernebelung:
Drücken Sie erneut, um mit einem Piepton in den
geringen Vernebelungsmodus zu wechseln.
Zwischen Starker & Geringer Vernebelung wechseln:
Drücken Sie erneut, um die starke Vernebelung
wieder zu aktivieren. Wechseln Sie mit jedem
Tastendruck zwischen den beiden Modi.
Halten Sie 2 Sekunden lang gedrückt, um die
Vernebelung auszuschalten.
Timer-Einstellung:
Drücken Sie bei eingeschaltetem Gerät, um einen
Timer von 1 / 3 / 6 Stunden einzustellen. Die
entsprechende Anzeige leuchtet dann auf.
Timer AUS:
Halten Sie bei eingeschaltetem Gerät 2 Sekunden
lang gedrückt, um den Timer jederzeit auszuschalten.
Automatische Farbwechsel:
Drücken Sie einmal, um den automatischen
Farbwechselmodus zu aktivieren, wobei 7 Farben
durchlaufen werden.
Bedienung und Funktionen
Schließen Sie das Gerät an einer Stromquelle an. Sobald es
angeschlossen ist, wechselt der Diffuser in den Standby-Modus. Bitte
stellen Sie sicher, dass sich genug Wasser im Tank befindet.
Funktionen Bedienung
Nebel AN
Nebel AUS
Timer-
Einstellungt
Beleucht-
ungsmodus-
Einstellung
Farbwahl:
Drücken Sie erneut, um bei der aktuellen Farbe zu
bleiben. Drücken Sie weiter, um durch die
verschiedenen Farben zu wechseln.
Trockengehschutz
Der Diffuser stellt sich automatisch ab, sobald der Wassertank leer
ist. Sobald wieder Wasser in den Tank gefüllt wird, nimmt der Diffuser
den Standby-Modus wieder auf.
Funktionen Bedienung
Beleucht-
ungsmodus-
Einstellung
Reinigung
WICHTIG!
Bitte trennen Sie das Gerät vor der Reinigung von der Stromver-
sorgung!
Regelmäßige Reinigung
1) Tank über den Wasserauslass leeren.
2) 3 bis 5 g (ca. einen Teelöffel, basierend auf der Menge der
Rückstände) Backpulver / NaHCO3 in den Tank geben.
3) Tank zur Hälfte mit warmem Wasser (200 bis 250 ml, 50°C)
füllen und rühren, bis das Pulver vollständig aufgelöst ist.
4) 3 bis 5 Minuten einwirken lassen, anschließend Tank und Tankab
deckung mit einer kleinen Brüste oder einem weichen Tuch mit
Backpulverlösung abwischen. (Zur besseren Reinigung die
abdämpfende Abdeckung entfernen und gründlich abwischen.)
5) Lösung wegschütten und Tank unter fließendem Wasser ausspülen.
6) Innen- und Außenseite mit einem trockenen Handtuch oder
sauberen Tuch abtrocknen.
7) Mögliche Backpulverreste abwischen.
Gründliche Reinigung
Sie sollten den Zerstäuber einmal im Monat oder bei geringer
Dampfausgabe aufgrund von Kalkablagerungen gründlich reinigen.
1) Tank über den Wasserauslass leeren.
2) 2 bis 3 Teelöffel Backpulver / NaHCO3 oder 2 bis 3 Scheiben frische
Zitrone in den Tank geben.
3) Tank zur Hälfte mit warmem Wasser (200 bis 250 ml, 50°C)
füllen und rühren, bis das Pulver vollständig aufgelöst ist.
4) Etwa eine halbe Stunde einwirken lassen.
5) Kalk an Boden und Zerstäuber (Schlitz in der Mitte) des Tanks mit
einer kleinen Bürste gründlich reinigen.
6) Tankabdeckung mit einer kleinen Brüste oder einem weichen Tuch
mit Backpulverlösung abwischen. (Zur besseren Reinigung die
abdämpfende Abdeckung entfernen und gründlich abwischen.)
7) Lösung wegschütten und Tank unter fließendem Wasser ausspülen.
8) Mögliche Backpulverreste abwischen.
9) Innen- und Außenseite mit einem trockenen Handtuch oder
sauberen Tuch abtrocknen.
Anmerkung:
1) Sie können auch Spülmittel nehmen, falls Sie kein Backpulver zur
Hand haben. Spülmittel eignet sich jedoch besser zur Entfernung
von Öl statt zur Entfernung von Gerüchen und Mineralablagerungen.
2) Basis nicht direkt mit Wasser abspülen. Tasten, Lichtöffnungen,
Lufteinlässe und Unterseite zur Vermeidung von Kurzschlüssen
nach Möglichkeit nicht feucht werden lassen.
3) Sie sollten das Gerät nicht mit weißem Essig reinigen, da direkter
und indirekter Kontakt mit dem Zerstäuber dauerhafte Schäden
verursachen kann.
Problemlösung
Nr. Problem Lösung
1
Die LED-Beleuchtung
geht nicht an, wenn
das Gerät
eingeschaltet wird.
Drücken Sie die Licht-Taste, um
die Beleuchtung einzuschalten.
2
Das Gerät stoppt den
Nebelausstoß und
das Licht blinkt als
Überhitzungssignal
rot.
Schalten Sie das Gerät aus.
Achten Sie auf die
Umgebungstemperatur und
stellen Sie das Gerät zum
Abkühlen an einen gut belüfteten
Ort.Füllen Sie kein warmes Wasser
in den Tank.
3Der Nebelausstoß
wird geringer.
Halten Sie das Wasser sauber
oder verwenden Sie gereinigtes
oder destilliertes Wasser.Reinigen
Sie den Zerstäuber regelmäßig.
4
Der Nebelausstoß
wird geringer und
stoppt schließlich.
Füllen Sie Wasser ein, wenn nicht
genügend Wasser im Tank ist.
5
Ablagerungen im
Wassertank und
Wasserreservoir
Reinigen Sie das Gerät wie im
Kapitel "Reinigung und Pflege"
beschrieben.
6
Eigenartiger Geruch
nach langer
Standzeit
Reinigen Sie das Gerät vor der
Nutzung sorgfältig.
7
Es verbleibt der
Geruch von vorher
verwendetem
ätherischem Öl im
Gerät.
Reinigen Sie das Gerät vor der
Nutzung sorgfältig.
Nr. Problem Lösung
8Nicht genügend
Diffusion
Schalten Sie den Starken
Vernebelungsmodus ein.
9Nasse
Tischoberfläche
Die Nebelstufe ist für die
Raumgröße zu hoch eingestellt.
Bitte regeln Sie die Nebelstufe
herunter.
10 Der Duft ist nicht
stark genug.
Geben Sie ätherisches Öl in die
Röhre, bis es leicht überläuft.
11
Kein Duft nach
Hinzugabe von
ätherischem Zimtöl
Ätherisches Zimtöl verfügt über
eine höhere Dichte und Viskosität
als Wasser. Wir empfehlen,
ätherisches Öl direkt auf die
Wasseroberfläche zu geben, um
die Diffusion zu beschleunigen.
12
Fehler beim
Auswählen einer
Farbe
Drücken Sie die Lichttaste einmal,
um den automatischen
Farbwechselmodus zu aktivieren.
Drücken Sie die Taste erneut, um
bei der aktuellen Farbe zu bleiben.
Drücken Sie weiter, um durch die
verschiedenen Farben zu
wechseln.
11 12 13 14 15 16 17 18 19
www.anjou.com
NORTH AMERICA
E-mail: support@anjou.com
MANUFACTURER
Manufacturer: Shenzhen NearbyExpress Technology
Development Co., Ltd.
Address: Floor 7, Building E, Galaxy World Phase II, Shenzhen, China
Rev_V1.2_EN-DE
AJ-PCN082
Eingang: 100-240V~ 50/60Hz
Ausgang: DC 24V 0.5A
＜10W
＞5h (Starker Nebel))
＞8h (Geringer Nebel)
60 ml / 2.0 fl. oz (Starker Nebel)
30 ml / 1.0 fl. oz (Geringer Nebel)
300 ml / 10.0 fl. oz
2.4MHz
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
WEEE Compliance
Correct Disposal of This Product (Waste Electrical & Electronic
Equipment) (Applicable in countries with separate collection systems)
This marking on the product, accessories or literature indicates that
the product and its electronic accessories should not be disposed of
with other household waste at the end of their working life. To prevent
possible harm to the environment or human health from uncontrolled
waste disposal, please separate these items from other types of
waste and recycle them responsibly to promote the sustainable reuse
of material resources. Household users should contact either the
retailer where they purchased this product, or their local government
office, for details of where and how they can take these items for
environmentally safe recycling. Business users should contact their
supplier and check the terms and conditions of the purchase
contract. This product and its electronic accessories should not be
mixed with other commercial wastes for disposal.
MADE IN CHINA
DE
Spezifikationen
Modell
Netzteil
Leistung
Betriebszeit
Nebelausstoß
Wassertank-Volumen
Ultraschallfrequenz
Im Lieferumfang enthalten
· 1 x Aroma-Diffuser
· 1 x Netzstecker
· 1 x Reinigungsbürste
· 1 x Bedienungsanleitung
· 1 x Dankeschön-Karte
· 1 x Tubus für Ätherische Öle
Bedienung
Achtung
1. Bitte geben Sie zunächst Wasser in den Tank, fügen Sie dann bis zur
Markierung am. Rohr oder bis zu Beginn der Ausgabe ätherisches Öl
hinein. Falls kein Duft wahrnehmbar ist, ist möglicherweise die
Wasser-Öl-Balance falsch. Bitte geben Sie genügend ätherisches Öl
entsprechend den Anweisungen hinein.
1H 3H 6H ON
2. Es wird empfohlen, gereinigtes oder destilliertes Wasser zu verwenden.
3. Ätherisches Zimtöl verfügt über eine höhere Dichte und Viskosität
als Wasser. Wenn Sie ätherisches Zimtöl ins Wasser geben, sinkt es
auf den Boden. Wir empfehlen, ätherisches Öl direkt auf die
Wasseroberfläche zu geben, um die Diffusion zu beschleunigen.
Einfüllen und Abgießen von Wasser
1. Nehmen Sie die Tankabdeckung ab und befüllen Sie den Tank bis
maximal zur max. Wasserstandslinie mit Wasser. Einige Tropfen
ätherisches Öl in das Rohr geben, bis die Ausgabe beginnt. Setzen
Sie die Tankabdeckung wieder auf.
2. Falls nötig, lassen Sie überschüssiges Wasser über den Seitenab
lauf abfließen.
3. Reinigen Sie den Wassertank mit der mitgelieferten Bürste, wenn
sich Ablagerungen bilden.
Anmerkung:
Gießen Sie nie ätherisches Öl ins Röhrchen, wenn kein Wasser im Tank ist.
1H 3H 6H ON 1H 3H 6H ON
1H 3H 6H ON
1H 3H 6H ON
Starke Vernebelung:
Drücken Sie einmal, um den standardmäßigen
starken Vernebelungsmodus zu aktivieren. Es erklingen
zwei Pieptöne und die ON-Anzeige leuchtet auf.
Geringe Vernebelung:
Drücken Sie erneut, um mit einem Piepton in den
geringen Vernebelungsmodus zu wechseln.
Zwischen Starker & Geringer Vernebelung wechseln:
Drücken Sie erneut, um die starke Vernebelung
wieder zu aktivieren. Wechseln Sie mit jedem
Tastendruck zwischen den beiden Modi.
Halten Sie 2 Sekunden lang gedrückt, um die
Vernebelung auszuschalten.
Timer-Einstellung:
Drücken Sie bei eingeschaltetem Gerät, um einen
Timer von 1 / 3 / 6 Stunden einzustellen. Die
entsprechende Anzeige leuchtet dann auf.
Timer AUS:
Halten Sie bei eingeschaltetem Gerät 2 Sekunden
lang gedrückt, um den Timer jederzeit auszuschalten.
Automatische Farbwechsel:
Drücken Sie einmal, um den automatischen
Farbwechselmodus zu aktivieren, wobei 7 Farben
durchlaufen werden.
Bedienung und Funktionen
Schließen Sie das Gerät an einer Stromquelle an. Sobald es
angeschlossen ist, wechselt der Diffuser in den Standby-Modus. Bitte
stellen Sie sicher, dass sich genug Wasser im Tank befindet.
Funktionen Bedienung
Nebel AN
Nebel AUS
Timer-
Einstellungt
Beleucht-
ungsmodus-
Einstellung
Farbwahl:
Drücken Sie erneut, um bei der aktuellen Farbe zu
bleiben. Drücken Sie weiter, um durch die
verschiedenen Farben zu wechseln.
Trockengehschutz
Der Diffuser stellt sich automatisch ab, sobald der Wassertank leer
ist. Sobald wieder Wasser in den Tank gefüllt wird, nimmt der Diffuser
den Standby-Modus wieder auf.
Funktionen Bedienung
Beleucht-
ungsmodus-
Einstellung
Reinigung
WICHTIG!
Bitte trennen Sie das Gerät vor der Reinigung von der Stromver-
sorgung!
Regelmäßige Reinigung
1) Tank über den Wasserauslass leeren.
2) 3 bis 5 g (ca. einen Teelöffel, basierend auf der Menge der
Rückstände) Backpulver / NaHCO3 in den Tank geben.
3) Tank zur Hälfte mit warmem Wasser (200 bis 250 ml, 50°C)
füllen und rühren, bis das Pulver vollständig aufgelöst ist.
4) 3 bis 5 Minuten einwirken lassen, anschließend Tank und Tankab
deckung mit einer kleinen Brüste oder einem weichen Tuch mit
Backpulverlösung abwischen. (Zur besseren Reinigung die
abdämpfende Abdeckung entfernen und gründlich abwischen.)
5) Lösung wegschütten und Tank unter fließendem Wasser ausspülen.
6) Innen- und Außenseite mit einem trockenen Handtuch oder
sauberen Tuch abtrocknen.
7) Mögliche Backpulverreste abwischen.
Gründliche Reinigung
Sie sollten den Zerstäuber einmal im Monat oder bei geringer
Dampfausgabe aufgrund von Kalkablagerungen gründlich reinigen.
1) Tank über den Wasserauslass leeren.
2) 2 bis 3 Teelöffel Backpulver / NaHCO3 oder 2 bis 3 Scheiben frische
Zitrone in den Tank geben.
3) Tank zur Hälfte mit warmem Wasser (200 bis 250 ml, 50°C)
füllen und rühren, bis das Pulver vollständig aufgelöst ist.
4) Etwa eine halbe Stunde einwirken lassen.
5) Kalk an Boden und Zerstäuber (Schlitz in der Mitte) des Tanks mit
einer kleinen Bürste gründlich reinigen.
6) Tankabdeckung mit einer kleinen Brüste oder einem weichen Tuch
mit Backpulverlösung abwischen. (Zur besseren Reinigung die
abdämpfende Abdeckung entfernen und gründlich abwischen.)
7) Lösung wegschütten und Tank unter fließendem Wasser ausspülen.
8) Mögliche Backpulverreste abwischen.
9) Innen- und Außenseite mit einem trockenen Handtuch oder
sauberen Tuch abtrocknen.
Anmerkung:
1) Sie können auch Spülmittel nehmen, falls Sie kein Backpulver zur
Hand haben. Spülmittel eignet sich jedoch besser zur Entfernung
von Öl statt zur Entfernung von Gerüchen und Mineralablagerungen.
2) Basis nicht direkt mit Wasser abspülen. Tasten, Lichtöffnungen,
Lufteinlässe und Unterseite zur Vermeidung von Kurzschlüssen
nach Möglichkeit nicht feucht werden lassen.
3) Sie sollten das Gerät nicht mit weißem Essig reinigen, da direkter
und indirekter Kontakt mit dem Zerstäuber dauerhafte Schäden
verursachen kann.
Problemlösung
Nr. Problem Lösung
1
Die LED-Beleuchtung
geht nicht an, wenn
das Gerät
eingeschaltet wird.
Drücken Sie die Licht-Taste, um
die Beleuchtung einzuschalten.
2
Das Gerät stoppt den
Nebelausstoß und
das Licht blinkt als
Überhitzungssignal
rot.
Schalten Sie das Gerät aus.
Achten Sie auf die
Umgebungstemperatur und
stellen Sie das Gerät zum
Abkühlen an einen gut belüfteten
Ort.Füllen Sie kein warmes Wasser
in den Tank.
3Der Nebelausstoß
wird geringer.
Halten Sie das Wasser sauber
oder verwenden Sie gereinigtes
oder destilliertes Wasser.Reinigen
Sie den Zerstäuber regelmäßig.
4
Der Nebelausstoß
wird geringer und
stoppt schließlich.
Füllen Sie Wasser ein, wenn nicht
genügend Wasser im Tank ist.
5
Ablagerungen im
Wassertank und
Wasserreservoir
Reinigen Sie das Gerät wie im
Kapitel "Reinigung und Pflege"
beschrieben.
6
Eigenartiger Geruch
nach langer
Standzeit
Reinigen Sie das Gerät vor der
Nutzung sorgfältig.
7
Es verbleibt der
Geruch von vorher
verwendetem
ätherischem Öl im
Gerät.
Reinigen Sie das Gerät vor der
Nutzung sorgfältig.
Nr. Problem Lösung
8Nicht genügend
Diffusion
Schalten Sie den Starken
Vernebelungsmodus ein.
9Nasse
Tischoberfläche
Die Nebelstufe ist für die
Raumgröße zu hoch eingestellt.
Bitte regeln Sie die Nebelstufe
herunter.
10 Der Duft ist nicht
stark genug.
Geben Sie ätherisches Öl in die
Röhre, bis es leicht überläuft.
11
Kein Duft nach
Hinzugabe von
ätherischem Zimtöl
Ätherisches Zimtöl verfügt über
eine höhere Dichte und Viskosität
als Wasser. Wir empfehlen,
ätherisches Öl direkt auf die
Wasseroberfläche zu geben, um
die Diffusion zu beschleunigen.
12
Fehler beim
Auswählen einer
Farbe
Drücken Sie die Lichttaste einmal,
um den automatischen
Farbwechselmodus zu aktivieren.
Drücken Sie die Taste erneut, um
bei der aktuellen Farbe zu bleiben.
Drücken Sie weiter, um durch die
verschiedenen Farben zu
wechseln.
11 12 13 14 15 16 17 18 19
www.anjou.com
NORTH AMERICA
E-mail: support@anjou.com
MANUFACTURER
Manufacturer: Shenzhen NearbyExpress Technology
Development Co., Ltd.
Address: Floor 7, Building E, Galaxy World Phase II, Shenzhen, China
Rev_V1.2_EN-DE
Table of contents
Other Anjou Accessories manuals
