ANK AOH211 User manual

CPIN007614
TECHNICAL SPECIFICATIONS
Model AOH211
Voltage 220-240V~
Frequency 50Hz
Rated Power 2000W-2400W
HEAT SETTING POWER
Low Heat 1000W
Medium Heat 1400W
High Heat 2400W
INSTRUCTION MANUAL
AOH211
WARNING!
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR PERSONAL INJURY, READ,
UNDERSTAND AND FOLLOW INSTRUCTIONS BEFORE USING THIS HEATER
OCH205
1000W
OPERATING INSTRUCTIONS
1. Unwind the cord to its full length and place the heater on a
firm, level, heat-resistant surface in a stable, upright position.
2. Visually inspect the ventilation holes to ensure that there are
no blockages.
3. Turn the thermostat knob to the minimum position and set
the power switch to OFF. Then insert the plug into a suitable
wall outlet (10Amp).
4. Turn the power switch from “0” to either “I” (Low Heat), “II”
(Medium Heat) or “III” (High Heat).
5. Turn the thermostat knob clockwise to maximum position,
once the room temperature rises to a comfortable level,
to maintain the room temperature, turn the knob anti-
clockwise until the indicator light turns OFF. The heater will
turn off but will automatically turn back on when it detects
that the ambient temperature has decreased. To lower
the temperature, turn the knob further anti-clockwise. To
increase the temperature, turn the knob further clockwise.
Note: There may be some non-harmful odour emitted from the
heater initially. This is normal during the break-in period or after
long-term storage. Place the heater is used in a well- ventilated
area and continue running it until the odour disappears.
Note: To avoid overloading a circuit do not plug the heater into a
circuit that already has other appliances working.
Note: Never leave this heater unattended when in use.
Caution: Make sure there is nothing flammable or heat sensitive
within 1 metre (40 inches). Operating the heater in any other
position could cause a hazard.
Caution: If there is an oil leak, do not use.
Warning: This product generates heat during operation, to avoid
overheating “DO NOT COVER” the product. Proper precautions must
be taken to prevent the risk of burns, scalds, fire or other damage
to individuals or property.
SAFETY CUT-OFF
THERMAL PROTECTIVE DEVICE
The heater has an overheat protection system that shuts off the
heater in the event of overheating.
If the heater stops working:
1. Turn OFF the heater and inspect the ventilation holes
for blockages.
2. Unplug the heater and wait for it to cool (approximately
30 minutes).
If the unit does not restart, the permanent thermal fuse has
operated, and the unit will not function. Do not attempt to
operate the unit, since the overheat protection system cannot
be reset by the user. Do not open the unit and rest by yourself.
There are no user serviceable parts inside.
TIP OVER SWITCH
This heater incorporates a tip over switch. If the unit is
tilted or knocked over the power will be cut automatically.
When the heater is returned to the upright position, it will
function normally.
CARE AND CLEANING
1. Before cleaning, turn off the heater, unplug it from
the power outlet and allow the heater to cool (approximately
30 minutes).
2. Carefully wipe the exterior of the heater with a soft damp
cloth and dry thoroughly with a dry cloth.
Note: Do not immerse the power cord, plug or heater into
water or any liquid or pour water or any other liquid over
the heater.
1. Over time, dust may accumulate. This can be removed by
wiping with a damp cloth, or by using the brush attachment
on your vacuum cleaner.
2. Make sure that the heater is dry before plugging it back into
the power outlet.
Any other servicing should be performed by an authorized
service representative. Do not use the heater if it has
malfunctioned or become damaged in any way. When the heater
is not in use, store in a cool dry location and take care not to
damage the product. Do not store until the heater is cool.
DISPOSAL OF THE UNIT
At the end of its working life, do not dispose of the heater
with your household waste. Observe any local requirements
regarding appropriate disposal or recycling of electrical goods.
Contact your local authorities for advice regarding recycling
facilities in your area.
12 Month Warranty
Thank you for your purchase.
Your new product is warrantied to be free from defects in materials and workmanship for
the period stated above, from the date of purchase, provided that the product is used in
accordance with accompanying recommendations or instructions where provided. This
warranty is in addition to your rights under the Australian Consumer Law.
For New Zealand customers, this warranty is in addition to statutory rights observed under
New Zealand legislation.
We will provide you with your choice of a refund, repair (where possible) or exchange
(availability dependent) for this product if it becomes defective within the warranty period.
The business will bear the reasonable expense of claiming the warranty.
This warranty will no longer apply where the defect is a result of alteration, accident,
misuse, abuse or neglect.
Please retain your receipt as proof of purchase and contact our Customer Service Centre
as listed below, for the entity you purchased this product from, for any difficulties with
your product. Warranty claims and claims for expense incurred in returning this product
can be addressed to the respective Customer Service Centre.
Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and compensation for
any other reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure does not
amount to a major failure.
Contact for Kmart purchases Contact for Target purchases
Kmart Australia Ltd.
C/- Customer Service Centre
690 Springvale Road,
Mulgrave Vic 3170
Customer Service: 1800 124 125
(Australia) or 0800 945 995
(New Zealand) or via
Customer Help at kmart.com.au
Target Australia Pty Ltd
C/- Customer Service Centre
2 Kendall Street, Williams Landing,
Vic, 3027
Customer Service: 1300 753 567 or
via Customer Help at target.com.au/
help/contact-us

A B
C
D
COMPONENTS
AHeater Body
BU-Shaped Bolts x 2
CStraight Wheel Assembly x2
DWing Nuts x 2
DIAGRAM
1Handle
2Indicator Light
3Thermostat Knob
4Switch Knob
5Heating Fins
6Cord Storage
7Wheel Assembly
1
2
3
4
5
6
7
CPIN007614
ASSEMBLY INSTRUCTIONS
Do not operate the heater without the wheelbase assembly in place. The heater must always be used in an upright
position. Remove any promotional material or any packaging from the heater. Please below figures as a reference
for installation.
1. Ensure the heater is switched OFF and unplugged, all components listed above are present.
2. Turn the heater upside down.
3. Hook the U-shaped bolt around the circular joint between the control box fin and second fin (fig. a).
4. Insert the curved end of U-shaped bolt into one of the holes on the wheel assembly, then insert the threaded end of
U-shaped bolt into the other hole on the wheel assembly. (fig. b).
5. Use the wing nut provided to tighten and position securely, do not over tighten. (fig. c).
6. Repeat steps 3,4 and 5 to mount the wheel assembly on the rear of heater, it must be mounted between last two fins.
7. Fig. d shows the correctly mounted wheel assembly positions.
IMPORTANT SAFEGUARDS
• This heater becomes hot during operation. To avoid
burns, do not let exposed skin come into contact with
hot surfaces.
• Use the handles provided when moving this heater.
Ensure combustible material, such as drapery and other
furnishings, is always at least 1 metre from the heater.
• Unplug the heater when not in use.
• When in use, ensure, the power cord does not meet the
heater body. Completely unwind the power cord before
first time use.
• Do not twist or kink the power cord as this may cause the
insulation to weaken and split.
• Do not operate the heater with a damaged power cord
or plug, if the heater has malfunctioned, or has been
dropped or damaged in any manner. Return the heater to
an authorised service representative for examination.
• If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
• This heater is designed only for indoor household use.
• Do not run the power cord under carpeting or cover
the power cord with combustible material such as throw
rugs runners.
• Keep the power cord away from traffic areas to avoid
tripping hazards.
• Before inserting or removing the plug, switch the heater
to the OFF position and turn the power off at the power
outlet. Always remove the plug by holding the plug top.
Do not pull the power cord.
• Do not insert or allow foreign objects to enter any
ventilation or exhaust opening as this may cause an
electric shock, fire, or damage to the heater.
• To reduce the risk of fire, do not cover fins in any manner.
• Do not use in areas where petrol, paint, or other
flammable liquids are used or stored.
• The use of extension leads is not recommended. If this
cannot be avoided, follow the manufacturer’s instructions
provided with the extension lead. Caution must be taken
to not exceed the ratings marked on the extension lead.
• Do not use this heater with any device that switches
the heater on automatically, such as a programmer or a
timer, as a fire risk may exist if the appliance is covered or
positioned incorrectly.
• To avoid a circuit overload when using this heater, do
not operate another high-wattage product on the same
electrical circuit. Make sure that your power outlet
voltage and circuit frequency corresponds to the a.c.
220V-240V, 50Hz.
• Do not use the heater to dry clothes.
• To reduce the risk of fire, do not leave this heater
unattended during use, especially when children or pets
are present. Unplug the product from the power outlet
when it is not in use.
• To eliminate a choking hazard for young children, remove
and safely discard the protective cover fitted to the power
plug of the heater, along with all packaging material and
promotional labels.
• There are no user serviceable parts in the heater.
Maintenance other than cleaning must be performed by
an authorised service representative.
• For additional protection when using this product, you
can install a residual current device (safety switch). A
safety switch with a rated residual operating current not
exceeding 30mA is recommended for installation in the
electrical circuit supplying power to the heater. Contact a
suitably qualified electrical contractor for advice.
• To avoid electric shock, do not touch this heater with any
part of the body that is damp or wet.
• Do not use the heater if it has malfunctioned or become
damaged in any way. When the heater is not in use, store
in a cool dry location and take care not to damage the
product. Do not store until the heater is cool.
WARNING
• The heater must not be located immediately below a
power outlet.
• Do not use this heater within the vicinity of a bath,
shower, or swimming pool.
• This product must be connected to an earthed socket-
outlet of a.c. 220V-240V, 50Hz.
• The heater is designed for indoor household use only.
• To avoid overheating, do not cover the heater. All items
must be at least 1 metre from the top, bottom, front,
sides, and rear of the heater.
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory, or
mental capabilities, or lack of experience and knowledge,
unless they are supervised or have been given instruction
concerning the use of the heater by a person responsible
for their safety.
• The heater is filled with a precise quantity of special oil.
Repair requiring opening of the oil container must only be
conducted by authorised service representative.
• When disposing of the heater, please contact your local
council for any special requirements regarding safe
disposal of the oil.
• Do not use this heater in small rooms when they are
occupied by persons not capable of leaving the room on
their own, unless constant supervision is provided.
• To reduce the risk of fire, keep textiles, curtains, or any
other flammable material a minimum distance of 1m from
the heater.
• Children should be supervised to ensure that they do not
play with the appliance.
Fig. a Fig. b Fig. c Fig. d