2202-036
Annex Products Pty Ltd, Australia, declares that the
products “Wireless Carplay Adaptor” complies with
part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
NOTE: The “Wireless CarPlay Adaptor” has been tested
and found to comply with the limits for a Class C device,
pursuant to Part 15 of the FCC Rules and has been assigned
FCC ID: 2AYC2-CPC200. These limits are designed to provide
reasonable protection against harmful interference. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
Consult the dealer or an experienced technician for help.
To maintain compliance with FCC’s RF Exposure guidelines,
this equipment should be installed and operated with a
minimum distance of 20cm between the radiator and your
body. Use only supplied antenna.
CAUTION: Any changes or modifications in construction of
these devices which are not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
Annex products Pty Ltd, Australia, declares that the
product “Wireless CarPlay Adaptor”, is in compliance
with EMC CE-RED Directive (2014/53/EU), CE-LVD
Directive (2014/35/EU) and EN 50498. The CE certificate of
conformity can be found at: www.quadlock.com.au/compliance
INDUSTRIE CANADA (IC: 28684-CPC200CP2A)
This device complies with Industry Canada’s license-exempt
RSSs. Operation is subject to the following two conditions:
• This device may not cause interference; and
• This device must accept any interference, including
interference that may cause undesired operation of the
device.
This equipment complies with Canada radiation exposure limits
set forth for an uncontrolled environment.
During the operation of device a distance of 10 cm surrounding
the device and 10 cm above the top surface of the device must
be respected.
Le présent appareil est conforme aux CNR d’Industrie
Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes:
• l’appareil ne doit pas produire de brouillage;
• l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
Cet équipement est conforme Canada limites d’exposition aux
radiations dans un environnement non contrôlé.
Au cours de l’opération de l’appareil sur une distance de 10
cm autour de l’appareil et de 10 cm au - dessus de la surface
supérieure de l’appareil doit être respecté.
UPDATING FIRMWARE
Connect your iPhone to the CarPlay Adapter and wait
until the CarPlay UI appears on your car’s display.
1. Enter
“192.168.50.2” in
your web browser
on your iPhone
and click “Go.”
2. Select update
if available.
3. Wait until the
update bar
reaches 100%.
When CarPlay
reappears on vehicle
infotainment screen,
you’re done!
3. Press X to delete individual users or the cog to
remove all phones (see step 4)
REMOVING ALL iPHONES FROM THE PAIR LIST
4.
*Apple and CarPlay are registered trademarks of Apple Inc
CANCELLING AUTOCONNECT
1.
2.
You may need to restart CarPlay Adaptor.
REMOVING AN iPHONE FROM THE PAIR LIST
1.
2.
