Anolis ArcSource Outdoor 4 MC User manual

1
User instructions
ArcSource Outdoor 4 MC
The Anolis ArcSource Outdoor 4 MC is a Cree MC-E RGBW multichip based high powered multicolored LED
xture. The unit can be used for large scale applications, as well as used for individual illuminating needs.
1.Attention
Consider the respective national norms during the installation!
Do not install the unit near naked ames.
Avoid using the unit in locations subject to possible impacts.
Do not attempt to dismantle or modify the unit.
Do not install the module in badly ventilated location
Avoid looking directly into the LED light beam at close range.
2.Installation
The ArcSource Outdoor 4 MC can be arranged in any position orientation. Three holes of diameter of 4.3mm
in the ArcSource Outdoor´s base serve for mounting on the non-ammable surface. The light head can be
adjust against the base in range of 120°.The ArcSource Outdoor units should be connected to the ArcPower
drivers stated in technical specications. See their user manuals for full details of mains power requirements
and DMX operation.
CAUTION!
Avoid looking directly into the LED light beam at close range!
Maximum possible number of LED modules connected to the one LED output of the ArcPower driver is men-
tioned in the table below.
Use a cable splitter if more than one LED module has to be connected to the one LED output of the ArcPower
driver, the connection cable between the ArcPower and the splitter is a standard RJ45 patch cable category
5 wired 1:1.
LED RGBW
multichips
Max.number of connected
modules ArcPower drivers
ArcSource Outdoor 4 MC 1 10 ArcPower 36/K2, ArcPower 72/K2,
ArcSource Outdoor 4 MC 1 12 ArcPower 384 Rack Mount
ArcSource Outdoor 4 MC 12 ArcPower 16x6*
* Use outputs intended for RGBW operation
The enclosed adapter stand (with M5x45 screw) allows to place light head higher:

3. Connection
ArcSource Outdoor 4 MC
Adapter cable Chogori -Chogori (it is not a standard part of delivery)
Adapter cable Chogori -RJ45 (it is not a standard part of delivery)
Connection to the ArcPower driver
ArcPower driver 2

4.Technical specications
cETLus version:
LED Device: Cree MC-E multichip
Available beam angles: 11°, 26°, 36°
Colour variants: RGBW, RGBA
Max. Current per Colour: 350 mA
Maximum Power Consumption: 6 W
Recommened Power Supply: ArcPower 16x6
Typical Lumen Maintenance: 70% @ 50.000 hours
Led Life Expectancy: minimum 50.000 hours
Cooling System: convection
Operating Ambient Temp.Range: -20°C/+45°C
Housing: alluminium
Weight: 0.62 kg
Mounting: via 3 holes in the base
Connection: cable Igus CF9.03.08 or other cable from 8x24AWG to
8x 20AWG, length=50 cm
Chogori CGRBDU-08BMMA-LL7G1B (connector, male)
Use in wet location
CE version:
LED Device: Cree MC-E multichip
Available beam angles: 11°, 26°, 36°
Colour variants: RGBW, RGBA,SW
Max. Current per Colour: 700 mA
Maximum Power Consumption: 10 W
Recommened Power Supplies: ArcPower 36/K2, ArcPower 72/K2, ArcPower 384 Rack M.
(ArcPower 36/K2 Smart White, ArcPower 72/K2 Smart
White for Smart White variant)
Typical Lumen Maintenance: 70% @ 50.000 hours
Led Life Expectancy: minimum 50.000 hours
Cooling System: convection
Operating Ambient Temp.Range: -20°C/+45°C
Housing: alluminium
Weight: 0.62 kg
Mounting: via 3 holes in the base
Connection: cable Igus CF9.03.08 or other cable from 8x24AWG to
8x 20AWG), length=50 cm
Chogori CGRBDU-08BMMA-LL7G1B (connector, male)
Ingress Protection: IP 67
5. Accessories
1x Connector Chogori CGRBDU-08BFFA-LL7G1B (female), IP=68
1x Adapter stand (No. 19730251)
1x Screw M5x45
1x Allen key 4
1x Splitter (No. 13050690)
6. Optional Accessories
Adapter cable CGRBDU-08BFFA/ CGRBDU-08BMMA, L=3m (No. 13051960), IP=68
Adapter cable CGRBDU-08BFFA/RJ4 RJ45, L=0.25m (No. 13051966)
T-connector Chogori 8-pin (No. 13051938), IP=67
Land spike 1 ASO 4 MC 100mm (No. 10980178)
Land spike 2 ASO 4 MC 100mm (No. 10980179)
Land spike 1 ASO 4 MC 500mm (No. 10980180)
Land spike 2 ASO 4 MC 500mm (No. 10980181)
Land spike 3 ASO 4 MC 500mm (No. 10980183)
3

4
7. Dimensions (mm)
Land spike 1 ASO 4 MC 100mm

5
Land spike 2 ASO 4 MC 100mm
Land spike 1 ASO 4 MC 500mm
Land spike 2 ASO 4 MC 500mm

6
Land spike 3 ASO 4 MC 500mm

7
8. Installing the ArcSource Outdoor 4 MC onto a land spike
Land spike 1 ASO 4 MC 100mm / Land spike 2 ASO 4 MC 100mm
1. Hammer the sharp part (1) of the land spike into ground
(hammer the centre of the sharp part, not the edge).
2. Screw the threaded bar (2) into the sharp part (1) and
secure it with the socket head M5x5 (3).
3 .Put the cover (4) on the threaded bar (2).
4. Put the pipe 36.5 mm (5) on the threaded bar (2).
5. Put the cable holder (6) on the threaded bar (2).
Land spike 1 ASO 4 MC 100mm only.
6. Screw the nut (7) on the threaded bar (2).
7. Screw the ArcSource Outdoor 4 MC on the nut (7).
(Use the socket head M5x14 from the ArcSource Outdoor
4 MC to screw it to the nut (7)).
8. Pass the cable throw the cable holder (6).
Land spike 2 ASO 4 MC 100mm only.
6. Put the pipe 42 mm (6) on the threaded bar (2).
7. Put the ArcSources holder (8) on the threaded bar (2).
8. Screw the nut (9) on the threaded bar (2).
9. Screw both ArcSource Outdoor 4 MC on the ArcSources
holder (8).
(Use the socket heads M5x14 from the ArcSource Outdoors
4 MC to screw them to the holder (8)).
10. Pass the cable throw the cable holder (6).
Land spike 1 ASO 4 MC 500mm / Land spike 2 ASO 4 MC 500mm
1. Hammer the sharp part (1) of the land spike into ground
(hammer the centre of the sharp part, not the edge).
2. Screw the threaded bar (2) into the sharp part (1) and
secure it with the socket head M5x5 (3).
3 .Put the cover (4) on the threaded bar (2).
4. Put the pipe 36.5mm (5) on the threaded bar (2).
5. Put the cable holder (6) on the threaded bar (2).
6. Put the pipe 198mm (7) on the threaded bar (2).
7. Put the cable holder (6) on the threaded bar (2).
8. Put the pipe 198mm (7) on the threaded bar (2).
Land spike 1 ASO 4 MC 500mm only:
9. Put the cable holder (6) on the threaded bar (2).
10. Screw the nut (8) on the threaded bar (2).
11. Screw the ArcSource Outdoor 4 MC on the nut (8).
(Use the socket head M5x14 from the ArcSource Outdoor
4 MC to screw it to the nut (7)).
12. Pass the cable throw the cable holders (6).
Land spike 2 ASO 4 MC 500mm only:
9. Put the ArcSources holder (8) on the threaded bar (2).
10. Screw the nut (9) on the threaded bar (2).
11. Screw both ArcSource Outdoor 4 MC on the ArcSources
holder (8).
(Use the socket head M5x14 from the ArcSource Outdoors
4 MC to screw them to the holder (8)).
12. Pass the cable throw the cable holders (6).

8
Land spike Land spike 3 ASO 4 MC 500mm
1. Hammer the sharp part (1) of the land spike into ground
(hammer the centre of the sharp part, not the edge).
2. Screw the threaded bar (2) into the sharp part (1) and
secure it with the socket head M5x5 (3).
3 .Put the cover (4) on the threaded bar (2).
4. Put the pipe 36.5mm (5) on the threaded bar (2).
5. Put the cable holders (6) on the threaded bar (2).
6. Put the pipe 198mm (7) on the threaded bar (2).
7. Put the ArcSources holder (8) on the threaded bar (2).
8. Put the pipe 198mm (7) on the threaded bar (2).
9. Put the cable holder (6) on the threaded bar (2).
10. Screw the nut with holder (9) on the threaded bar (2).
11. Screw ArcSources Outdoor 4 MC on the ArcSources
holders (8,9).
(Use the socket head M5x14 from the ArcSource Outdoors
4 MC to screw them to the holder (8)).
12. Pass the cable throw the cable holders (6).
Version 1.6 CE/cETLus
February 27, 2014
Specications are subject to change without notice.