Anritsu Microwave Site Master S820E User manual

User Guide
Microwave Site Master™
S820E
Cable and Antenna Analyzer Featuring Classic and
Advanced Modes
Anritsu Company
490 Jarvis Drive
Morgan Hill, CA 95037-2809
USA
http://www.anritsu.com
Part Number: 10580-00343
Revision: F
Published: June 2015
Copyright 2013, 2015 Anritsu Company

Title-2 PN: 10580-00343 Rev. F S820E UG
WARRANTY
The Anritsu product listed on the title page is warranted against defects in materials and
workmanship for three years from the date of shipment.
Anritsu’s obligation covers repairing or replacing products which prove to be defective during the
warranty period. Buyers shall prepay transportation charges for equipment returned to Anritsu
for warranty repairs. Obligation is limited to the original purchaser. Anritsu is not liable for
consequential damages. Accessories included with this product are not included in the standard
warranty.
LIMITATION OF WARRANTY
The foregoing warranty does not apply to Anritsu connectors that have failed due to normal
wear. Also, the warranty does not apply to defects resulting from improper or inadequate
maintenance, unauthorized modification or misuse, or operation outside of the environmental
specifications of the product. No other warranty is expressed or implied, and the remedies
provided herein are the Buyer’s sole and exclusive remedies.
DISCLAIMER OF WARRANTY
DISCLAIMER OF WARRANTIES. TO THE MAXIMUM EXTENT PERMITTED BY
APPLICABLE LAW, ANRITSU COMPANY AND ITS SUPPLIERS DISCLAIM ALL
WARRANTIES, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO,
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, WITH REGARD TO THE PRODUCT. THE USER ASSUMES THE ENTIRE RISK
OF USING THE PRODUCT. ANY LIABILITY OF PROVIDER OR MANUFACTURER WILL BE
LIMITED EXCLUSIVELY TO PRODUCT REPLACEMENT.
NO LIABILITY FOR CONSEQUENTIAL DAMAGES. TO THE MAXIMUM EXTENT
PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL ANRITSU COMPANY OR ITS
SUPPLIERS BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR
CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION,
DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF
BUSINESS INFORMATION, OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF THE
USE OF OR INABILITY TO USE THE PRODUCT, EVEN IF ANRITSU COMPANY HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES AND
JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR
CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT
APPLY TO YOU.
TRADEMARK ACKNOWLEDGMENTS
Acrobat Reader is a registered trademark of Adobe Corporation.
Site Master is a trademark of Anritsu Company. All rights reserved.
NOTICE
Anritsu Company has prepared this manual for use by Anritsu Company personnel and
customers as a guide for the proper installation, operation and maintenance of Anritsu Company
equipment and computer programs. The drawings, specifications, and information contained
herein are the property of Anritsu Company, and any unauthorized use or disclosure of these
drawings, specifications, and information is prohibited; they shall not be reproduced, copied, or
used in whole or in part as the basis for manufacture or sale of the equipment or software
programs without the prior written consent of Anritsu Company.
UPDATES
Updates, if any, can be downloaded from the Documents area of the Anritsu web site at:
http://www.anritsu.com
For the latest service and sales information in your area, please visit:
http://www.anritsu.com/contact.asp

S820E UG PN: 10580-00343 Rev. F Title-3

Title-4 PN: 10580-00343 Rev. F S820E UG
Notes On Export Management
This product and its manuals may require an Export License or approval by
the government of the product country of origin for re-export from your
country.
Before you export this product or any of its manuals, please contact Anritsu
Company to confirm whether or not these items are export-controlled.
When disposing of export-controlled items, the products and manuals need to
be broken or shredded to such a degree that they cannot be unlawfully used
for military purposes.
CE Conformity Marking
Anritsu affixes the CE Conformity marking onto its conforming products in
accordance with Council Directives of The Council Of The European
Communities in order to indicate that these products conform to the EMC
and LVD directive of the European Union (EU).
C-tick Conformity Marking
Anritsu affixes the C-tick marking onto its conforming products in accordance
with the electromagnetic compliance regulations of Australia and New
Zealand in order to indicate that these products conform to the EMC
regulations of Australia and New Zealand.
Perchlorate Material – Special Handling May Apply
Notification for California customers: this product uses a small Lithium
battery installed internally on the circuit board that may contain perchlorate.
Disposal may be regulated due to environmental considerations. Please
contact your local authorities for disposal or recycling information. For
information, see: http://www.dtsc.ca.gov/hazardouswaste/perchlorate/

S820E UG PN: 10580-00343 Rev. F Title-5
European Parliament and Council Directive 2002/96/EC
Chinese RoHS Compliance Statement

Title-6 PN: 10580-00343 Rev. F S820E UG

S820E UG PN: 10580-00343 Rev. F Safety-1
Safety Symbols
To prevent the risk of personal injury or loss related to equipment
malfunction, Anritsu Company uses the following symbols to indicate
safety-related information. For your own safety, please read the information
carefully before operating the equipment.
Symbols Used in Manuals
Danger
This indicates a risk from a very dangerous condition or
procedure that could result in serious injury or death and
possible loss related to equipment malfunction. Follow all
precautions and procedures to minimize this risk.
Warning This indicates a risk from a hazardous condition or
procedure that could result in light-to-severe injury or loss
related to equipment malfunction. Follow all precautions
and procedures to minimize this risk.
Caution
This indicates a risk from a hazardous procedure that could
result in loss related to equipment malfunction. Follow all
precautions and procedures to minimize this risk.

Safety-2 PN: 10580-00343 Rev. F S820E UG
Safety Symbols Used on Equipment and in Manuals
The following safety symbols are used inside or on the equipment near
operation locations to provide information about safety items and operation
precautions. Ensure that you clearly understand the meanings of the symbols
and take the necessary precautions before operating the equipment. Some or
all of the following five symbols may or may not be used on all Anritsu
equipment. In addition, there may be other labels attached to products that
are not shown in the diagrams in this manual.
This indicates a prohibited operation. The prohibited
operation is indicated symbolically in or near the barred
circle.
This indicates a compulsory safety precaution. The required
operation is indicated symbolically in or near the circle.
This indicates a warning or caution. The contents are
indicated symbolically in or near the triangle.
This indicates a note. The contents are described in the
box.
These indicate that the marked part should be recycled.

S820E UG PN: 10580-00343 Rev. F Safety-3
For Safety
Warning Always refer to the operation manual when working
near locations at which the alert mark, shown on the
left, is attached. If the operation, etc., is performed
without heeding the advice in the operation manual,
there is a risk of personal injury. In addition, the
equipment performance may be reduced. Moreover,
this alert mark is sometimes used with other marks
and descriptions indicating other dangers.
Warning
When supplying power to this equipment, connect
the accessory 3-pin power cord to a 3-pin grounded
power outlet. If power is supplied without grounding
the equipment, there is a risk of receiving a severe
or fatal electric shock.
Warning
This equipment can not be repaired by the operator.
Do not attempt to remove the equipment covers or to
disassemble internal components. Only qualified
service technicians with a knowledge of electrical
fire and shock hazards should service this
equipment. There are high-voltage parts in this
equipment presenting a risk of severe injury or fatal
electric shock to untrained personnel. In addition,
there is a risk of damage to precision components.

Safety-4 PN: 10580-00343 Rev. F S820E UG
For Safety
Caution
Electrostatic Discharge (ESD) can damage the
highly sensitive circuits in the instrument. ESD is
most likely to occur as test devices are being
connected to, or disconnected from, the instrument’s
front and rear panel ports and connectors. You can
protect the instrument and test devices by wearing a
static-discharge wristband. Alternatively, you can
ground yourself to discharge any static charge by
touching the outer chassis of the grounded
instrument before touching the instrument’s front
and rear panel ports and connectors. Avoid touching
the test port center conductors unless you are
properly grounded and have eliminated the
possibility of static discharge.
Repair of damage that is found to be caused by
electrostatic discharge is not covered under
warranty.
Warning
This product is supplied with a rechargeable battery
that could potentially leak hazardous compounds
into the environment. These hazardous compounds
present a risk of injury or loss due to exposure.
Anritsu Company recommends removing the battery
for long-term storage of the instrument and storing
the battery in a leak-proof, plastic container. Follow
the environmental storage requirements specified in
the product data sheet.