Anritsu MT8820C Installation and operating instructions

Revision History
Ver.
No
Date
Contents
Related product
software version
1.00
May 2015
MT8820C/21C LTE Application Note (Ver. 1.00) is based on
MT8820C LTE Application Note (Ver. 15.00).
Overall: Added MT8821C option model names to MT8820C option
model names
Overall: Added DL CA and UL CA test procedures for MT8821C
Added MT8821C software specification.
MX882012C/42C
Ver. 23.20
MX882112C/42C
Ver. 30.00
2.00 Sep 2015 •
1.5.2
Added FDD-TDD 2,3DL/1UL CA, SISO and MIMO to
Supported CA Combination of MT8821C.
•2.4 / 3.6 / 5.3 Added MT8821C connection/RX-measurement/
IP-data-transfer-test procedures for 4DL CA.
•3.3 Added MT8821C measurement procedures for Inter-band
UL CA.
•3.7 Added MT8821C UL Throughput measurement procedure
for SCC.
•7Added MT8821C VoLTE Echoback test procedure.
•Annex B.2 Added mention of Carrier Leakage Frequency for
measurements on MT8821C intra-band contiguous CC.
•Annex B.3 Added description about optimization of TCP
Throughput by Iperf.
•
AnnexB.4 Added maximum rate setting for DL 256QAM.
MX882012C/42C
Ver23.20
MX882112C/42C
Ver30.10
3.00 Dec 2015 •1.2 Supported 6.2.3_2, 6.6.2.1_1, 6.6.2.3_2 of 3GPP
Measurement Specification for MT8820C
•2.2 Added MT8820C setting procedures for FDD-TDD 2DL/1UL
CA.
•3.4.1 Modified test procedures for MT8820C.
•
3.4.5 Modified test procedures for MT8820C.
MX882012C/42C
Ver23.30
MX882112C/42C
Ver30.12
4.00
Jan 2016
•8Added MT8821C SMS test procedure.
MX882012C/42C
Ver23.30
MX882112C/42C
Ver30.20
Application Note
LTE Measurements
Radio Communication Analyzer MT8820C/MT8821C

5.00
Mar 2016
•1.2 Updated 3GPP measurement standard list (2015-12)
•1.3 Added Band 45, 65-67.
•1.5.2 / 2.5 / 3.7 Added 5DL CA test procedures.
•3.3 / 3.4 / 3.5 Added test procedures associated with updating
3GPP measurement standard list.
•5.4 Added IP Data Application.
•8Added 4x4 MIMO test procedures.
MX882012C/42C
Ver23.30
MX882112C/42C
Ver30.30
6.00
Jun 2016
•1.2 Supported 7.4A.3_H,7.4A.4_H of 3GPP Measurement
Specification for MT8821C.
•3.4 Added 7.4A.3_H,7.4A.4_H of 3GPP Measurement
Specification for MT8821C test procedure.
•
3.4.11 Modified test procedures.
MX882012C/42C
Ver23.30
MX882112C/42C
Ver30.32
7.00
Oct 2016
•1.3 Added Band 66, 250.
•2.2.8.3 Added RB Allocation Detail Mode setting method.
•3.2 / 3.3 / 3.4 / 3.5 /3.6 Added test procedures associated with
updating 3GPP measurement standard list (2016-03).
•3.3.2.11 Added test procedures associated with updating 3GPP
measurement standard list (2016-06).
•9 Added 4x2 MIMO test procedure and Maximum Throughput
setting method.
•10 Added CSAT measurement procedure.
•11 Added Antenna Selection measurement procedure.
•
B.1 Added 4x4 MIMO and DL256QAM conditions.
MX882012C/42C
Ver23.30
MX882112C/42C
Ver30.40
8.00 Oct 2017
•1.3 Added Band 48, 68, 69, 70.
•1.1.2.16 / 1.5.2 Added 6DL CA condition.
•2.6, 3.8.2 Added test procedure and Connection Diagram for
5DL CA SISO/2x2MIMO with 2units.
•2.7, Added test procedure and Connection Diagram for 6DL CA
SISO with 1unit (TBD)
•2.8 Added test procedure and Connection Diagram for 6DL CA
SISO/2x2MIMO with 2units.
•3.3 Added test procedures associated with updating 3GPP
measurement standard list.
•3.11 Added SRS(Sounding Reference Signal) Measurements
•3.12 Added RX test procedure for the case including LAA SCell.
•6.3.2.4 Added Measurement Report test procedure for any
Intra-Frequencys and Inter-Frequencys.
•6.4 Added UE Capability Information Enquiry
•9.4 Added test procedure for 4DL CA 4x4 MIMO.
•12 Added LAA test procedure.
•Annex B.1.2 Added Code Rate display function
MX882012C/42C
Ver23.32
MX882112C/42C
Ver30.60
8.01
Nov 2017
•1.3 Fixed the description about supported Band in MT8821C.
MX882012C/42C
Ver23.32
MX882112C/42C
Ver30.60
2

Contents
LTE Measurement Software..........................................................................................51.
SPECIFICATIONS......................................................................................................................................51.1.
3GPP MEASUREMENT SPECIFICATION (3GPPTS 36.521-1 V12.8.0(2015-12)) TABLE ..........................221.2.
OPERATION BANDS................................................................................................................................401.3.
BAND 13 SUPPLEMENTARYRF CONFORMANCE MEASUREMENT SPECIFICATION TABLE ...............421.4.
SUPPORTED CACOMBINATION ..............................................................................................................421.5.
The Basic Operations...................................................................................................502.
LTE NON CA.........................................................................................................................................502.1.
2DL CAWITHOUT ULCA/2DLCAWITH ULCA......................................................................................532.2.
3DL CA ................................................................................................................................................702.3.
4DL CA ................................................................................................................................................812.4.
5DL CA(ONE MT8821C UNIT CONFIGURATION).....................................................................................872.5.
5DL CA(TWO MT8821C UNITS CONFIGURATION)..................................................................................912.6.
6DL CA(ONE MT8821C UNIT CONFIGURATION)...................................................................................1022.7.
6DL CA(TWO MT8821C UNITS CONFIGURATION)................................................................................1022.8.
TRX Measurements (Fundamental Measurements) .............................................1133.
TX MEASUREMENTS.............................................................................................................................1133.1.
RX MEASUREMENTS ...........................................................................................................................1503.2.
TX MEASUREMENTS FOR CA...............................................................................................................1543.3.
RX MEASUREMENTS FOR CA...............................................................................................................1943.4.
RX MEASUREMENTS FOR 3DLCA.......................................................................................................2013.5.
RX MEASUREMENTS FOR 4DLCA.......................................................................................................2193.6.
RX MEASUREMENTS FOR 5DLCA.......................................................................................................2243.7.
RX MEASUREMENTS FOR MT8821C ULCA2CCS..............................................................................2253.8.
TEST PARAMETERS SUPPORTING 3GPPTEST ITEMS............................................................................2313.9.
REMOTE COMMANDS LIST SETTING PASS/FAIL JUDGMENT VALUES.....................................................2373.10.
SRS (SOUNDING REFERENCE SIGNAL)MEASUREMENTS....................................................................2483.11.
RX MEASUREMENTS FOR CAINCLUDING LAASCELL.........................................................................2493.12.
BAND 13 SUPPLEMENTARY RF CONFORMANCE MEASUREMENT .........................2514.
PUCCH OVER-PROVISIONING FUNCTIONALTEST (2.7) ............................................................2514.1.
SPURIOUS EMISSIONS WITH TX GATING (2.9) ............................................................................2514.2.
IP Data Transfer Test .................................................................................................2535.
IPDATA TRANSFER TEST FOR NON CA(SINGLE CELL)..........................................................................2535.1.
IPDATA TRANSFER TEST FOR 2DLCA.................................................................................................2775.2.
IPDATA TRANSFER TEST FOR 3/4DLCA..............................................................................................2945.3.
IPDATA APPLICATION..........................................................................................................................3075.4.
3

RRM ..............................................................................................................................3096.
1PORT CS FALLBACK/REDIRECTION ....................................................................................................3096.1.
CELL RESELECTION.............................................................................................................................3136.2.
MEASUREMENT REPORT......................................................................................................................3196.3.
UE CAPABILITY INFORMATION ENQUIRY................................................................................................3226.4.
LTE VoLTE Echoback Test (MT8821C Only) ..............................................................3237.
LTE VOLTE ECHOBACK TEST..............................................................................................................3237.1.
SMS Test (MT8821C Only) ..........................................................................................3368.
MT8821C UE SMS SEND...............................................................................................................3368.1.
UE MT8821C SMS RECEIVE..........................................................................................................3368.2.
4x2, 4x4 MIMO (MT8821C Only)................................................................................3379.
4X4MIMO..........................................................................................................................................3379.1.
4X2MIMO..........................................................................................................................................3409.2.
3DL CAWITHOUT ULCA.....................................................................................................................3429.3.
4DL CAWITHOUT ULCA.....................................................................................................................3499.4.
MAXIMUM THROUGHPUT......................................................................................................................3589.5.
IPDATA TRANSFER..............................................................................................................................3599.6.
CSAT (MT8821C Only)...............................................................................................36010.
CSAT ...............................................................................................................................................36010.1.
ECSAT .............................................................................................................................................36110.2.
Antenna Selection Connection and Measurement .............................................36311.
CONNECTION DIAGRAM .....................................................................................................................36311.1.
CONNECTION AND MEASUREMENT PROCEDURE..................................................................................36311.2.
LAA (MT8821C Only) .................................................................................................36512.
ALL SUBFRAME TRANSMISSION SETTING............................................................................................36512.1.
FLEXIBLE TRANSMISSION SCHEDULING SETTING ................................................................................36612.2.
RX MEASUREMENT FOR REFERENCE SENSITIVITY/MAX INPUT LEVEL SETTING ....................................36812.3.
Annex A: ARB Waveform List........................................................................................370
A.1.ARBWAVEFORM INSTALLER VERSION:Q007 ......................................................................................370
A.2.ARBWAVEFORM INSTALLER VERSION:Q008 ......................................................................................370
Annex B: Informative ....................................................................................................372
B.1. UE DL-SCH RX.................................................................................................................................372
B.2. CARRIER LEAKAGE FREQUENCY..........................................................................................................386
B.3.ABOUT OPTIMIZATION OF THE TCP THROUGHPUT USING IPERF.............................................................388
B.4. SETTING FOR DL256QAM MAXIMUM THROUGHPUT RATE...................................................................390
4

LTE Measurement Software1.
Specifications1.1.
MT8820C1.1.1.
1.1.1.1. MX882012C/13C (Call Processing)
Table 1.1.1.1-1 LTE Measurement Software Specifications (MX882012C/13C)
Measurement Item Specifications
Electrical
Typical values (typ.) are only for reference and are not guaranteed.
Modulation Analysis
Frequency 400 to 2700 MHz
3400 to 3800 MHz
(Can be used when installing MT8820C-018 option)
Input level –40 to +35 dBm (Main1)
Carrier frequency
accuracy
±(Set frequency × Reference oscillator accuracy
+15 Hz)
Modulation accuracy
Residual vector error ≤2.5% (400 to 2700 MHz)
(3400 to 3800 MHz, 18° to 28°C)
(When measurement count is 20)
≤3.0% (3400 to 3800 MHz, 20 measurements)
In-band Emissions ≤–40 dB
(≥–10 dBm, Allocated RB≤18)
Measurement object PUSCH, PRACH, PUCCH
Amplitude
M
easurement
Frequency 400 to 2700 MHz
3400 to 3800 MHz
(Can be used when installing MT8820C-018 option)
Input level –60 to +35 dBm (Main1)
Measurement accuracy ±0.5 dB (–20 to +35 dBm),
typ. ±0.3 dB (–20 to +35 dBm)
±0.7 dB (–50 to –20 dBm)
±0.9 dB (–60 to –50 dBm)
400 to 2700 MHz, 10° to 40°C after calibration
±0.5 dB (–20 to +35 dBm, 18° to 28°C),
typ. ±0.3 dB (–20 to +35 dBm, 18° to 28°C),
±0.7 dB (–50 to –20 dBm),
±0.9 dB (–60 to –50 dBm),
3400 to 3800 MHz, 10° to 40°C after calibration
Linearity ±0.2 dB (–40 to 0 dB, ≥–50 dBm)
±0.4 dB (–40 to 0 dB, ≥–60 dBm)
400 to 2700 MHz
±0.2 dB (–40 to 0 dB, ≥–50 dBm, 18° to 28°C),
±0.3 dB (–40 to 0 dB, ≥–50 dBm)
±0.4 dB (–40 to 0 dB, ≥–60 dBm)
3400 to 3800 MHz, 10° to 40°C after calibration
Relative measurement error
<2 dB
typ. ±0.10 dB (–40 to 0 dB, ≥–50 dBm)
5

Measurement Item Specifications
Measurement object PUSCH, PRACH, PUCCH
Occupied B
andwidth
Frequency 400 to 2700 MHz
3400 to 3800 MHz
(Can be used when installing MT8820C-018 option)
Input level –10 to +35 dBm (Main1)
Adjacent
Channel
Leakage P
ower
Frequency 400 to 2700 MHz
3400 to 3800 MHz
(Can be used when installing MT8820C-018 option)
Input level –10 to +35 dBm (Main1)
Measurement point E-UTRA ACLR1
UTRA ACLR1
UTRA ACLR2
Measurement range ≥45 dB (E-UTRA ACLR1)
≥50 dB (UTRA ACLR1)
≥55 dB (UTRA ACLR2)
Spectrum
E
mission
M
ask
Frequency 400 to 2700 MHz
3400 to 3800 MHz
(Can be used when installing MT8820C-018 option)
Input level –10 to +35 dBm (Main1)
RF Signal G
enerator
Output frequency 400 to 2700 MHz (1-Hz steps)
3400 to 3800 MHz (1-Hz steps)
(Can be used when installing MT8820C-018 option)
AWGN level Off, –20 to +5 dB (0.1-dB steps,
Relative level with Ior (Total power))
AWGN level accuracy ±0.2 dB (Relative level accuracy with Ior)
Throughput
M
easurement
Function Measures throughput using RMC
Measurement object ACK and NACK reported from UE
Call
Processing
Call control Position registration, Call processing using RMC
(Executes each processing in 3GPP standards and performs Pass/Fail evaluation)
UE Control Output level
(Executes each UE control in 3GPP standards)
6

1.1.1.2. MX882012C/13C-006
Table 1.1.1.2-1 LTE FDD/TDD IP Data Transfer
Item Specifications
Function
The Ethernet port of the LTE measurement hardware can be used to transfer
data to external devices.
1.1.1.3. MX882012C/13C-011
Table 1.1.1.3-1 LTE FDD/TDD 2x2 MIMO DL
Item Specifications
Function
This can be used to measure the Rx performance of 2x2 MIMO mobile wireless
terminals.
RF Signal Generator
Output frequency: 400 to 2700 MHz (1-Hz steps)
3400 to 3800 MHz
(Can be used when installing MT8820C-018 option)
Throughput
M
easurement
Function: Throughput measurement using RMC
Measurement target: ACK and NACK reported from UE
1.1.1.4. MX882012C/13C-016
Table 1.1.1.4-1 LTE FDD/TDD CS Fallback to W-CDMA/GSM
Item Specification
Function
Supports CS fallback to W-CDMA or GSM using MT8820Cs
1.1.1.5. MX882012C/13C-017
Table 1.1.1.5-1 LTE FDD/ TDD CS Fallback to CDMA2000
Item Specification
Function
Supports CS fallback to CDMA2000 using MT8820Cs
1.1.1.6. MX882013C-018
Table 1.1.1.6-1 LTE TDD CS Fallback to TD-SCDMA/GSM
Item Specification
Function
Supports CS fallback to TD-SCDMA or GSM using MT8820Cs
7

1.1.1.7. MX882012C/13C-021
Table 1.1.1.7-1 LTE-Advanced FDD/TDD DL CA Measurement Software
Item Specification
Function
The reception measurements of DL 2CCs and UL 1CC described in Chapter 7 of
3GPP TS 36.521-1 and the maximum throughput tests are supported.
The maximum throughput test for DL CA 2x2 MIMO is supported by using with
the MX882012C/13C -011 2x2 MIMO DL option.
RF Signal Generator
Output frequency: 400 to 2700 MHz (1-Hz steps)
3400 to 3800 MHz
(Can be used when installing MT8820C-018 option)
Throughput
M
easurement
Function: Throughput measurement using RMC
Measurement target: ACK and NACK reported from UE
1.1.1.8. MX882012C/13C-022
Table 1.1.1.8-1 LTE-Advanced FDD/TDD UL CA Measurement Software
Item Specification
Function
When this option is installed with the LTE Advanced FDD/TDD DL CA
measurement software (MX882012C/13C-021) it supports a function to operate
as a Mobile Wireless Device and measurements for RF Transition and
Reception on UL CA.
Intra-Band Contiguous DL CA and UL CA is NOT supported.
Modulation Analysis
Equivalent to MX882012C/13C in respective CC measurements
RF Power
Equivalent to MX882012C/13C in respective CC measurements
Occupied Bandwidth
Equivalent to MX882012C/13C in respective CC measurements
Adjacent Channel
Leakage Power
Equivalent to MX882012C/13C in respective CC measurements
Spectrum Emission
Mask
Equivalent to MX882012C/13C in respective CC measurements
RF Signal Generator
Output frequency: 400 to 2700 MHz (1-Hz steps)
3400 to 3800 MHz
(Can be used when installing MT8820C-018 option)
Throughput
M
easurement
Function: Throughput measurement using RMC
Measurement target: ACK and NACK reported from UE
1.1.1.9. MX882012C/13C-026
Table 1.1.1.9-1 LTE-Advanced FDD/TDD DL CA IP Data Transfer
Item Specifications
Function
IP data transfer with external devices by using Ethernet port of LTE
measurement hardware is supported in DL CA.
8

1.1.1.10. MX882012C/13C-031
Table 1.1.1.10-1 LTE-Advanced FDD/TDD DL CA 3CCs Measurement Software
Item Specifications
Function
The reception measurements for
DL 3CCs and UL 1CC, and maximum
throughput tests are supported.
The maximum throughput test for DL CA 2x2 MIMO is supported b
y using with
the MX882012C/13C-011 LTE FDD/TDD 2x2 MIMO DL option.
RF Signal Generator
Output frequency: 400 to 2700 MHz (1-Hz steps)
3400 to 3800 MHz
(Can be used when installing MT8820C-018 option)
Throughput
M
easurement
Function: Throughput measurement using RMC
Measurement target: ACK and NACK reported from UE
9

1.1.1.11. MX882042C/43C (Non-Call Processing)
Table 1.1.1.11-1 Measurement Software Specifications (MX882042C/43C) (1/2)
Measurement Item Specifications
Electrical
Typical values (typ.) are only for reference and are not guaranteed.
Frequency/Modulation
M
easurement
Frequency 400 to 2700 MHz
3400 to 3800 MHz
(Can be used when installing MT8820C-018 option)
Input level –40 to +35 dBm (Main1)
Carrier frequency
accuracy
±(Set frequency × Reference oscillator accuracy
+15 Hz)
Modulation accuracy
Residual vector error ≤2.5% (400 to 2700 MHz)
(3400 to 3800 MHz, 18° to 28°C)
(When measurement count is 20)
≤3.0% (3400 to 3800 MHz, 20 measurements)
In-band Emissions ≤–40 dB
(≥–10 dBm, Allocated RB≤18)
Measurement object PUSCH
Amplitude
M
easurement
Frequency 400 to 2700 MHz
3400 to 3800 MHz
(Can be used when installing MT8820C-018 option)
Input level –60 to +35 dBm (Main1)
Measurement accuracy ±0.5 dB (–20 to +35 dBm)
typ. ±0.3 dB (–20 to +35 dBm)
±0.7 dB (–50 to –20 dBm)
±0.9 dB (–60 to –50 dBm)
400 to 2700 MHz, 10° to 40°C after calibration
±0.5 dB (–20 to +35 dBm, 18° to 28°C),
typ. ±0.3 dB (–20 to +35 dBm, 18 to 28°C),
±0.7 dB (–50 to –20 dBm),
±0.9 dB (–60 to –50 dBm),
3400 to 3800 MHz, 10° to 40°C after calibration
Linearity ±0.2 dB (–40 to 0 dB, ≥–50 dBm),
±0.4 dB (–40 to 0 dB, ≥–60 dBm),
400 to 2700 MHz
±0.2 dB (–40 to 0 dB, ≥–50 dBm, 18° to 28°C),
±0.3 dB (–40 to 0 dB, ≥–50 dBm),
±0.4 dB (–40 to 0 dB, ≥–60 dBm),
3400 to 3800 MHz, 10° to 40°C after calibration
Relative measurement error
<2 dB
typ. ±0.10 dB (–40 to 0 dB, ≥–50 dBm)
Measurement object PUSCH
10

Table 1.1.1.11-2 Measurement Software Specifications (MX882042C/43C) (2/2)
Measurement Item Specifications
Occupied
Bandwidth
Frequency 400 to 2700 MHz
3400 to 3800 MHz
(Can be used when installing MT8820C-018 option)
Input level –10 to +35 dBm (Main1)
Adjacent Channel
Leakage P
ower
Frequency 400 to 2700 MHz
3400 to 3800 MHz
(Can be used when installing MT8820C-018 option)
Input level –10 to +35 dBm (Main1)
Measurement point E-UTRA ACLR1
UTRA ACLR1
UTRA ACLR2
Measurement range ≥45 dB (E-UTRA ACLR1)
≥50 dB (UTRA ACLR1)
≥55 dB (UTRA ACLR2)
Spectrum Emission
M
ask
Frequency 400 to 2700 MHz
3400 to 3800 MHz
(Can be used when installing MT8820C-018 option)
Input level –10 to +35 dBm (Main1)
11

MT8821C1.1.2.
1.1.2.1. MX882112C/13C (Call Processing)
Table 1.1.2.1-1 LTE Measurement Software Specifications (MX882112C/13C) (1/3)
Measurement Item Specifications
Electrical
Typical values (typ.) are only for reference and are not guaranteed.
Frequency/Modulation
measurement
Frequency 400 to 3800 MHz
3800 to 5000 MHz
(Can be used when installing MT8821C-019 option)
For
frequencies below 500 MHz, only the following
range meets the specifications:
452.5 to 457.5 MHz (LTE OperatingBand31)
Input level –40 to +35 dBm (Main1/2)
Carrier frequency
accuracy ±(Set frequency × Reference oscillator accuracy +15 Hz)
Modulation accuracy
Residual vector error ≤ 2.5% (400 MHz ≤ Freq. ≤ 3800 MHz)
(When measurement count is 20)
≤ 3.5% (3800 MHz < Freq. ≤ 5000 MHz)
(When measurement count is 20)
In-band Emissions ≤–40 dB
(≥–10 dBm, Allocated RB ≤ 18)
Measurement object PUSCH, PRACH, PUCCH
Amplitude
M
easurement
Frequency 400 to 3800 MHz
3800 to 5000 MHz
(Can be used when installing MT8821C-019 option)
For frequencies below 500 MHz, only the following
range meets the specifications:
452.5 to 457.5 MHz (LTE OperatingBand31)
Input level –60 to +35 dBm (Main1/2)
Measurement accuracy ±0.5 dB (–20 to +35 dBm)
typ. ±0.3 dB (–20 to +35 dBm)
±0.7 dB (–50 to –20 dBm)
±0.9 dB (–60 to –50 dBm)
400 MHz ≤ Freq. ≤ 3800 MHz
10° to 40°C after calibration
±0.7 dB (–20 to +35 dBm)
±0.9 dB (–50 to –20 dBm)
±1.1 dB (–60 to –50 dBm)
3800 MHz <freq.≤ 5000 MHz
20° to 30°C after calibration
Linearity ±0.2 dB (–40 to 0 dB, ≥–50 dBm)
±0.4 dB (–40 to 0 dB, ≥–60 dBm)
400 to 5000 MHz
Measurement object PUSCH, PRACH, PUCCH
12

Table 1.1.2.1-1 LTE Measurement Software Specifications (MX882112C/13C) (2/3)
Measurement Item Specifications
Occupied
Bandwidth
Frequency 400 to 3800 MHz
3800 to 5000 MHz
(Can be used when installing MT8821C-019 option)
For frequencies below 500 MHz, only the following
range meets the specifications:
452.5 to 457.5 MHz (LTE OperatingBand31)
Input level –10 to +35 dBm (Main1/2)
Channel bandwidth 1.4 MHz, 3 MHz, 5 MHz
(452.5 MHz ≤ UL frequency ≤ 457.5 MHz)
1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz,
20 MHz (500 MHz ≤ UL frequency)
Adjacent Channel
Leakage P
ower
Frequency 400 to 3800 MHz
3800 to 5000 MHz
(Can be used when installing MT8821C-019 option)
For frequencies below 500 MHz, only the following
range meets the specifications:
452.5 to 457.5 MHz (LTE OperatingBand31)
Input level –10 to +35 dBm (Main1/2)
Measurement point E-UTRA ACLR1
UTRA ACLR1
UTRA ACLR2
Measurement range ≥ 45 dB (E-UTRA ACLR1)
≥ 50 dB (UTRA ACLR1)
≥ 55 dB (UTRA ACLR2)
Channel bandwidth 1.4 MHz, 3 MHz, 5 MHz
(452.5 MHz ≤ UL frequency ≤ 457.5 MHz)
1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz
20 MHz (500 MHz ≤ UL frequency)
Spectrum
E
mission
M
ask
Frequency 400 to 3800 MHz
3800 to 5000 MHz
(Can be used when installing MT8821C-019 option)
For frequencies below 500 MHz, only the following
range meets the specifications:
452.5 to 457.5 MHz (LTE OperatingBand31)
Input level –10 to +35 dBm (Main1/2)
Channel bandwidth 1.4 MHz, 3 MHz, 5 MHz
(452.5 MHz ≤ UL frequency ≤ 457.5 MHz)
1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz,
20 MHz (500 MHz ≤ UL frequency)
13

Table 1.1.2.1-1 LTE Measurement Software Specifications (MX882112C/13C) (3/3)
Measurement Item Specifications
RF
Signal Generator
Output frequency 400 to 3800 MHz (1-Hz steps)
3800 to 6000 MHz (1-Hz steps)
(Can be used when installing MT8821C-019 option)
AWGN level Off, –20 to +5 dB (0.1-dB steps,
Relative level with Ior (Total power))
AWGN level accuracy ±0.2 dB (Relative level accuracy with Ior)
Throughput
M
easurement
Function Measures throughput using RMC
Measurement object ACK and NACK reported from UE
Call P
rocessing
Call control Position registration, Call processing using RMC
(Executes each processing in 3GPP standards and performs Pass/Fail evaluation)
UE Control Output level
(Executes each UE control in 3GPP standards)
14

1.1.2.2. MX882112C/13C-006
Table 1.1.2.2-1 LTE FDD/TDD IP Data Transfer
Item Specifications
Function
The Ethernet port of the LTE measurement hardware can be used to transfer
data to external devices.
1.1.2.3. MX882112C/13C-011
Table 1.1.2.3-1 LTE FDD/TDD 2x2 MIMO DL
Item Specifications
Function
This can be used to measure the Rx performance of 2x2 MIMO mobile wireless
terminals.
RF
Signal Generator
Output frequency: 400 to 3800 MHz (1-Hz steps)
400 to 6000 MHz
(Can be used when installing MT8821C-019 option)
Throughput
M
easurement
Function: Throughput measurement using RMC
Measurement target: ACK and NACK reported from UE
1.1.2.4. MX882112C/13C-012
Table 1.1.2.4-1 LTE FDD/TDD 4x4 MIMO DL
Item Specifications
Function
This can be used to measure the Rx performance of 4x4 MIMO mobile wireless
terminals.
RF Signal Generator
Output frequency: 400 to 3800 MHz (1-Hz steps)
400 to 6000 MHz
(Can be used when installing MT8821C-019 option)
Throughput
Measurement
Function: Throughput measurement using RMC
Measurement target: ACK and NACK reported from UE
1.1.2.5. MX882112C/13C-016
Table 1.1.2.5-1 LTE FDD/TDD CS Fallback to W-CDMA/GSM
Item Specification
Function
Supports CS fallback to W-CDMA or GSM using MT8821C
1.1.2.6. MX882112C/13C-017
Table 1.1.2.6-1 LTE FDD/ TDD CS Fallback to CDMA2000
Item Specification
Function
Supports CS fallback to CDMA2000 using MT8821C
15

1.1.2.7. MX882113C-018
Table 1.1.2.7-1 LTE TDD CS Fallback to TD-SCDMA/GSM
Item Specification
Function
Supports CS fallback to TD-SCDMA or GSM using MT8821C
1.1.2.8. MX882112C/13C-021
Table 1.1.2.8-1 LTE-Advanced FDD/TDD DL CA Measurement Software
Item Specification
Function
The reception measurements for DL 2CCs and UL 1CC described in Chapter 7
of 3GPP TS 36.521-1 and the maximum throughput tests are supported.
The maximum throughput test for DL CA 2x2 MIMO is supported b
y using with
the MX882012C
/13C -011 2x2 MIMO DL option.
RF Signal Generator
Output frequency: 400 to 2700 MHz (1-Hz steps)
3400 to 3800 MHz
(Can be used when installing MT8821C-018 option)
Throughput
M
easurement
Function: Throughput measurement using RMC
Measurement target: ACK and NACK reported from UE
1.1.2.9. MX882112C/13C-022
Table 1.1.2.9-1 LTE-Advanced FDD/TDD UL CA Measurement Software
Item Specification
Function
This can be used to measure the functions and Tx/Rx performance of UEs
at
2CCs UL CA.
Frequency 500 to 3800 MHz
3800 to 4200 MHz
(Can be used when installing MT8821C-019 option)
Modulation Analysis
Same as MX882112C for CC measurements. The measurement target is only
PUSCH.
16

Table 1.1.2.9-2 LTE-Advanced FDD/TDD UL CA Measurement Software (Cont’d)
Amplitude
Measurement
Same as MX882112C except measurement accuracy and linearity in CC
measurements. The measurement target is only PUSCH.
Measurement accuracy ±0.7 dB (–20 to +35 dBm)
±0.9 dB (–50 to –20 dBm)
500 MHz ≤ Freq. ≤ 3000 MHz
10° to 40°C after calibration
±1.0 dB (–50 to +35 dBm)
±1.3 dB (–60 to –50 dBm)
3000 MHz < Freq. ≤ 3800 MHz
10° to 40°C after calibration
±1.0 dB (–50 to +35 dBm),
±1.3 dB (–60 to –50 dBm),
3800 MHz < Freq. ≤ 4200 MHz,
20° to 30°C after calibration
(At Intra-band Contig
uous CA SCC, PCC+SCC
measurement)
Linearity ±0.2 dB
(–40 to 0 dB, ≥–50 dBm, 20° to 30°C
after calibration),
±0.4 dB (–40 to 0 dB, ≥–60 dBm, 20° to 30°C
after calibration),
500 to 4200 MHz
Occupied Bandwidth
Same as MX882112C at CC or Contiguous CC measurements. The measurement
target is only PUSCH.
Adjacent Channel
Leakage Power
Same as MX882112C at CC or Contiguous CC measurements. The measurement
target is only PUSCH.
Spectrum Emission
Mask
Same as MX882112C at CC or Contiguous CC measurements. The measurement
target is only PUSCH.
RF Signal Generator
Output frequency
400 to 3800 MHz (1-Hz steps)
3800 to 6000 MHz (1-Hz steps)
(Can be used when
installing MT8821C-019 option)
Throughput
Measurement
Function
Throughput measurement using RMC
Measurement target
ACK and NACK reported from UE
1.1.2.10. MX882112C/13C-026
Table 1.1.2.10-1 LTE-Advanced FDD/TDD DL CA IP Data Transfer
Item Specifications
Function
At DL CA, IP data transfer is supported by using the internal server of the
MT8821C, or IP data transfer with external devices is supported by using the
Ethernet port of the LTE measurement hardware.
17

1.1.2.11. MX882112C/13C-031
Table 1.1.2.11-1 LTE-Advanced FDD/TDD DL CA 3CCs Measurement Software
Item Specifications
Function
The reception measurements for
DL 3CCs and UL 1CC, and the maximum
throughput tests are supported.
The maximum throughput test for DL CA 2x2 MIMO is supported b
y using with
the MX882012C/13C-011 LTE FDD/TDD 2x2 MIMO DL option.
RF Signal Generator
Output frequency: 400 to 3800 MHz (1-Hz steps)
400 to 6000 MHz
(Can be used when installing MT8821C-019 option)
Throughput
M
easurement
Function: Throughput measurement using RMC
Measurement target: ACK and NACK reported from UE
1.1.2.12. MX882112C/13C-036
Table 1.1.2.12-1 LTE-Advanced FDD/TDD DL CA 3CCs IP Data Transfer
Item Specifications
Function
At DL CA 3CCs, IP data transfer is supported by using the internal server of the
MT8821C, or IP data transfer with external devices is supported by using the
Ethernet port of the LTE measurement hardware.
1.1.2.13. MX882112C/13C-041
Table 1.1.2.13-1 LTE-Advanced FDD/TDD DL CA 4CCs Measurement Software
Item Specifications
Function
The reception measurements for DL 4
CCs and UL 1CC, and the maximum
throughput tests are supported.
The maximum throughput test for DL CA 2x2 MIMO is supported by using with
the MX882012C/13C-011 LTE FDD/TDD 2x2 MIMO DL option.
RF Signal Generator
Output frequency: 400 to 3800 MHz (1-Hz steps)
400 to 6000 MHz
(Can be used when installing MT8821C-019 option)
Throughput
Measurement
Function: Throughput measurement using RMC
Measurement target: ACK and NACK reported from UE
1.1.2.14. MX882112C/13C-046
Table 1.1.2.14-1 LTE-Advanced FDD/TDD DL CA 4CCs IP Data Transfer
Item Specifications
Function
At DL CA 4CCs, IP data transfer is supported by using the internal server of the
MT8821C, or IP data transfer with external devices is supported by using the
Ethernet port of the LTE measurement hardware.
18

1.1.2.15. MX882112C/13C-051
Table 1.1.2.15-1 LTE-Advanced FDD/TDD DL CA 5CCs Measurement Software
Item Specifications
Function
The reception measurements for DL 5
CCs and UL 1CC, and the maximum
throughput tests are supported.
RF Signal Generator
Output frequency: 400 to 3800 MHz (1-Hz steps)
400 to 6000 MHz
(Can be used when installing MT8821C-019 option)
Throughput
Measurement
Function: Throughput measurement using RMC
Measurement target: ACK and NACK reported from UE
1.1.2.16. MX882112C/13C-061
Table 1.1.2.15-1 LTE-Advanced FDD/TDD DL CA 6CCs Measurement Software
Item Specifications
Function
The reception measurements for DL 6
CCs and UL 1CC, and the maximum
throughput tests are supported.
RF Signal Generator
Output frequency: 400 to 3800 MHz (1-Hz steps)
400 to 6000 MHz
(Can be used when installing MT8821C-019 option)
Throughput
Measurement
Function: Throughput measurement using RMC
Measurement target: ACK and NACK reported from UE
19

1.1.2.17. MX882142C/43C (Non-Call Processing)
Table 1.1.2.16-1 Measurement Software Specifications (MX882042C/43C) (1/2)
Measurement Item Specifications
Electrical
Typical values (typ.) are only for reference and are not guaranteed.
Frequency/Modulation
M
easurement
Frequency 400 to 3800 MHz
3800 to 5000 MHz
(Can be used when installing MT8821C-019 option)
Input level –40 to +35 dBm (Main1/2)
Carrier frequency
accuracy
±(Set frequency × Reference oscillator accuracy
+15 Hz)
Modulation accuracy
Residual vector error ≤2.5% (400 to 3800 MHz)
(When measurement count is 20)
≤3.5% (3800 to 5000 MHz)
(When measurement count is 20)
In-band Emissions ≤–40 dB
(≥–10 dBm, Allocated RB≤18)
Measurement object PUSCH
Amplitude
M
easurement
Frequency 400 to 3800 MHz
3800 to 5000 MHz
(Can be used when installing MT8821C-019 option)
Input level –60 to +35 dBm (Main1/2)
Measurement accuracy ±0.5 dB (–20 to +35 dBm)
typ. ±0.3 dB (–20 to +35 dBm)
±0.7 dB (–50 to –20 dBm)
±0.9 dB (–60 to –50 dBm)
400 to 3800 MHz, 10° to 40°C after calibration
±0.7 dB (–20 to +35 dBm)
±0.9 dB (–50 to –20 dBm)
±1.1 dB (–60 to –50 dBm)
3800 to 5000 MHz, 10° to 40°C after calibration
Linearity ±0.2 dB (–40 to 0 dB, ≥–50 dBm)
±0.4 dB (–40 to 0 dB, ≥–60 dBm)
400 to 5000 MHz
Measurement object PUSCH
20