ANTAIRA LNX-1604G-SFP Series User manual

Antaira Technologies
LNX-1604G-SFP series
16-Port Industrial Gigabit Unmanaged Ethernet Switches with
12*10/100/1000Tx + 4*100/1000 SFP Slots
Quick Installation Guide
Version 1.0
Tel: [phone]
Fax: [phone]
www.antaira.com
19020000000002
Package Check List
The package contains the following items:
Quick Installation Guide
1 * LNX-1604G (-T) Industrial Gigabit Ethernet
Unmanaged Switch
1 * Wall mounting bracket set with screws
1 * DC cable –18 AWG & DC jack 5.5x2.1mm
Front Panel Layout
Top Panel View
LNX-1604G-SFP series top panel is equipped with one 6-pin
removal terminal block connector for dual DC power inputs
(12-48 VDC).
Product Overview
System Interface/Performance
All RJ-45 ports support the auto MDI/MDI-X function
Ethernet connectivity 12*10/100/1000Tx RJ45 ports
Fiber connectivity with 4*100/1000 Dual rate SFP slots
Store-and-forward switching architecture
8k MAC address table
Jumbo frame support up to 12.2k
Power line EFT protection: 2,000VDC; Ethernet ESD
protection: 6,000VDC
Power Input& Connection
DC 12~48V redundant power, with a 6-pin removal terminal
block
It is recommended to using UL listed Industrial Power
Supply
Operating Temperature
Standard operating temperature model: -10°C ~ 70°C
Extended operating temperature model (–T): -40°C ~ 75°C
Case/Installation
IP-30 protection
DIN-Rail and wall mount design
Safety Precaution
If the DC voltage is supplied by an external circuit, please use a
protection device on the power supply input.
LED Indicators
LED
Color
Description
Power 1
Green
On
Power input 1 is active
Off
Power input 1 is inactive
Power 2
Green
On
Power input 2 is active
Off
Power input 2 is inactive
Fault
Red
On
Power input 1 or 2 is inactive
Off
Both power input 1 and 2 are active
Link Activity
(SFP Port)
Green
On
Connected to the network with 1000Mbps
Flashing
Networking is active
Off
Not connected to the network
Amber
On
Connected to the network with 100Mbps
Flashing
Networking is active
Off
Not connected to the network
LAN Port
1~ 12
(Upper LED)
Green
On
Connected to network, 1000Mbps
Flashing
Networking is active
Off
Not connected to network
LAN Port
1~ 12
(Lower LED)
Green
On
Connected to network, 10/100Mbps
Flashing
Networking is active
Off
Not connected to network
Quick Installation
Ethernet Port
RJ45 Ports (Auto MDI/MDIX)
All RJ-45 ports are auto-sensing for 10Base-T, 100Base-TX or
1000Base-T devices connections. Please follow below wiring pin
assignment table for Ethernet port installation.
RJ45 Ethernet Port Pin Outs
Pins
T568A Color
T568B Color
10/100
Base-T(X)
1000
Base-T
Pin 1
White/Green
White/Orange
Rx+
TP0+
Pin 2
Green
Orange
Rx-
TP0-
Pin 3
White/Orange
White/Green
Tx+
TP1+
Pin 4
Blue
Blue
unused
TP2+
Pin 5
White/Blue
White/Blue
unused
TP2-
Pin 6
Orange
Green
Tx-
TP1-
Pin 7
White/Brown
White/Brown
unused
TP3+
Pin 8
Brown
Brown
unused
TP3-
Grounding Screw
6-Pin Removal Terminal Block (Power Input)
LED for Power 1, Power 2 and Fault
LAN# 13~16 LED for Network activity
SFP for LAN# 13~16 100/1000Mbps Fiber
LAN# 1~12 LED for 1000Mbps
LAN# 1~12 –10/100/1000 RJ45
LAN# 1~12 LED for 10/100Mbps

SFP Slots
The small form-factor pluggable (SFP) is a compact optical
transceiver used in optical communications.
Please follow below steps for connecting the SFP and LC cable:
1. Insert the SFP transceiver module into the SFP slot as
shown below in Figure 1 (Notice that the triangle mark is at
the bottom of the SFP slot).Figure 2 shows SFP transceiver
module was inserted.
Figure 1 Figure 2
2. Insert the fiber cable of the LC connector into the transceiver
as shown below in Figure 3.
Figure 3
Power Inputs Wiring
Please follow the below steps to insert the power wire:
1. Insert the positive and negative wires into the PWR1
(V1+, V1-) and PWR2 (V2+, V2-) contacts on the
terminal block connector as shown below in Figure 4.
2. Tighten the wire-clamp screws to prevent the wires from
loosening, as shown below in Figure 5.
Figure 4 Figure 5
Industrial Switch Mounting
DIN-Rail Mounting
The DIN-Rail bracket is
pre-installed on the industrial
Ethernet switch from the factory.
Please refer to Figure 6 for
DIN-Rail bracket installation
reference.
Follow below steps for installing the Industrial Switch on the
DIN-Rail track:
1. Insert the top of the DIN-Rail on to the track as shown below
in Figure 7.
2. Lightly pull down the bracket on to the rail as shown below in
Figure 8.
3. Check if the bracket is mounted tightly on the rail.
4. To remove the industrial
Ethernet
switch from the rail, do the
opposite from the above steps.
Figure 7 Figure 8
Wall Mounting
Follow the steps below to mount the industrial Ethernet switch
using the wall mounting bracket as shown below in Figure 9.
.
1. Remove the DIN-Rail bracket from the industrial Ethernet
switch by loosening the screws.
2. Place the wall mounting
brackets on the top and bottom
of the industrial Ethernet
switch.
3. Use the screws to screw the
wall mounting bracket on the
industrial Ethernet switch.
4. Use the hook holes at the
corners of the wall mounting
bracket to hang the industrial
Ethernet switch on the wall.
5. To remove the wall mount
bracket, do the opposite from
the steps above. Figure 9
Field Maintenance and Service
If the device requires servicing of any kind, the user is
required to disconnect and remove it from its mounting. The
initial installation should be done in a way that makes this as
convenient as possible.
Voltage/Power lines should be properly insulated as well as
other cables. Be careful when handling them so as to not trip
over.
Do not under any circumstance insert foreign objects of any
kind into the heat dissipation holes located in the different
faces of the device. This may not only harm the internal
layout, but might cause harm to user as well.
Do not under any circumstance open the device for any
reason. Please contact your dealer for any repair needed or
follow the instructions within the manual.
Warranty Policy
Warranty Conditions
Products supplied by Antaira Technologies are covered in this
warranty for sub-standard performance or defective
workmanship. The warranty is not, however, extended to goods
damaged in the following circumstances:
(a) Excessive forces or impacts
(b) War or an Act of God: wind storm, fire, flood, electric shock,
earthquake
(c) Use of unqualified power supply, connectors, or
unauthorized parts/kits
(d) Replacement with unauthorized parts
RMA and Shipping Costs Reimbursement
Customers shall always obtain an authorized "RMA" number
from Antaira before shipping the goods for repair or
replacement.
Within the warranty period (based on the invoice date), all
parts and labor are free of charge to the customers.
Customers are required to be responsible for the cost of
parts and labor, if the products are out of warranty.
For RMA service, customers are required to be responsible
for the shipping expense for shipping the RMA unit(s) to
Antaira; and Antaira will be responsible for the shipping
expense by ground service for the return repair/replace
unit(s) back to customers.
Limited Liability
Antaira would not be held responsible for any consequential
losses from using Antaira’s product.
Warranty Period
5-Year Warranty
Antaira’s Customer Service and Support
Antaira’s Technical Service & Support Centers:
+ 844-268-2472 (Antaira US Headquarter)
+ 48-22-862-88-81 (Antaira Europe Office)
+ 886-2-2218-9733 (Antaira Asia Office)
Antaira’s Web Sites & Repair/Support Emails:
www.antaira.com / [email protected]
www.antaira.eu / i[email protected]
www.antaira.com.tw / i[email protected]
*Any changes will be announced on the Antaira website.
Figure 6