Antari LCU-1 User manual

    
 
ð
2012 Antari Lighting and Effects Ltd.
 Ne

2

3
Antari LCU-1 Liquid Control Unit User Manual
Congratulations on the purchase of your new
ANTARI LCU-1 Liquid Control Unit.
ð
Introduction
Thank you for choosing an ANTARI Liquid Control Unit. You now own a
rugged and powerful state-of-the-art machine. Prior to use, we suggest
that you carefully read all of the instructions. By following the
suggestions found in this user manual, you can look forward to the
reliable and satisfactory performance of your ANTARI Liquid Control Unit
for years to come.
Please follow these operation, safety and maintenance instructions
to ensure a long and safe life for your Control Unit.
Cautions
Risk of electric shock. Disconnect the appliance from the
electric supply before removing the cover. Note: there are
no user serviceable parts inside.
!

4
Danger of electric shock
♦Keep this device dry.
♦For inside use only. Not designed for outside use.
♦For the 110V models, use 3-prong grounded electrical outlet only.
Prior to use take care to determine that the unit is installed at the
rated voltage.
♦Keep Liquid Control Unit upright.
♦Turn off or unplug when not in use.
♦This machine is not water- or splash-proof. If moisture, water, or fog
liquid gets inside the housing, immediately unplug the unit and
contact a service technician or your ANTARI dealer before using it
again.
♦No user serviceable parts inside. Refer to your ANTARI dealer or
other qualified service personnel.
Danger of burns
♦For adult use only. Liquid Control Unit must be installed out of the
reach of children. Never leave the unit running unattended.
♦Locate the fog machine in a well-ventilated area. In order to
guarantee adequate ventilation, allow a free air space of at least 20
cm around the sides and top of the unit.
♦Keep flammable materials at least 50 cm away from the Unit
♦Always allow your ANTARI Liquid Control Unit to cool down before
attempting to clean or service it.

5
Danger of explosion
♦Never add flammable liquids of any kind (oil, gas, perfume) to the
Liquid Control Unit.
Pay attention to all warning labels and instructions printed on the exterior
of your ANTARI Liquid Control Unit
♦Maximum pressure of the pump inside the machine is 7 BAR.
♦Maximum fog output is 20,000 cubic feet/minute.
♦Visibility during operation is reduced.
♦Use only the high-quality, water-based fog liquid that your dealer
recommends. Other fog liquids may cause clogging or “spitting”.
♦Operating this unit without liquid will cause damage to the pump.
♦If your ANTARI Liquid Control Unit fails to work properly, discontinue
use immediately, pack the unit securely (preferably in the original
packing material), and return it to your ANTARI dealer for service.
ð
Unpacking & Inspection
Open the shipping carton and verify that all equipment necessary to
operate the system has arrived intact. Refer to the “Features” section
for information on what items are included with your model. If any
equipment is missing contact your ANTARI dealer immediately.
Before beginning initial setup of your ANTARI Liquid Control Unit, make
sure that there is no evident damage caused by transportation. In the
event that the unit’s housing or cable is damaged, do not plug it in and
do not attempt to use it until after contacting your ANTARI dealer for
assistance.

6
ð
Setup
♦See connection diagram
♦Remove all packing materials from shipping box. Check that all foam
and plastic padding is removed.
♦Place Liquid Control Unit on a flat surface.
♦Put a Tank beside Liquid Control Unit and connect a 6mm PU tube
between Tank & Liquid Input Adapter
♦Connect 6mm PU tube from Liquid Output Adapter then extend this
tube to
four Z-1200 fog machine (S-100IIs / ICEs). Each terminal use FT-6 ,
FTA-64
and FTA-664 divide liquid flow direction.
♦Firmly attach the remote control cable to the proper input on the rear
of the machine.
♦If you are connecting the machine to a DMX controller or in a daisy
chain of DMX controlled devices ensure the various cables are
connected to the proper socket on the back of the fog machine.

7
ð
Operation
♦Plug power cord into a grounded electrical outlet. If necessary, turn
power switch on rear of unit to “ON” position.
♦To extrude liquid, press the appropriate button on the remote for the
desired length of time.
♦For further information on operating your ANTARI Liquid Control Unit,
refer to the Antari onboard, “Remote Control Operation”.
♦For details regarding DMX, refer to the Antari onboard DMX fog
machine settings section.
If you experience low output, pump noise or no output at all, unplug
immediately. Check Tank fluid level, the external fuse, remote
connection, and power from the wall. If all of the above appears to be
O.K., plug the unit in again. If fluid does not come out after holding the
remote button down for 30 seconds, check the tube attached to the tank
to make sure there is fluid going through the tube. If you are unable to
determine the cause of the problem, do not simply continue pushing the
remote button, as this may damage the unit. Return the machine to your
ANTARI dealer.
Cleaning your fog machine regularly will help reduce costly parts
replacement and repair charges.
ð
Maintenance
Do not allow the fog liquid to become contaminated. Always replace the
caps on the fog liquid container and the fog machine liquid tank
immediately after filling.

8
After every 40 hours of continuous operation, it is recommended to run a
cleaning solution composed of 80% distilled water/20% white vinegar
through the system to prevent the accumulation of particulate matter in
the tube. The recommended cleaning regimen is as follows:
1. While unit is unplugged and clean out debris with vinegar and a pipe
cleaner, making sure that the tube is free of clogs.
2. Add cleaning solution to tank. Run unit in a open area until tank is
empty.
3. Cleaning is now complete. Refill with fog liquid.
4. Clean with a dry cloth only.
5. Store dry.
Read and save these instructions