AnthroDesk AD-DMP-1 User manual

ASSEMBLY INSTRUCTIONS
Model: AD-DMP-1
Programmable Dual Motor Standing Desk
WWW.ANTHRODESK.CA 1-800-267-1783
(Rev: 27102022)

Electric Controls:
Input Voltage: 100-240Vac 50/60Hz Input Current ≤ 3A
Output Voltage: 24V DC
Duty Cycle: 10% MAX 2min On 18min Off
Rated For Low Energy Consumption
Desk Frame:
Built-in Limit Switch
Dynamic Load: 135KG
Maximum Static Load: 140KG
Load Speed: 1.18"/sec.
Lift Range: 24.5" - 50" (62cm - 127cm)
Adjustable Width Range: 46" - 63" (117cm - 160cm)
Packaging:
Carton Size: 1270*245*320mm (1 set)
Gross Weight: 39.5KG
Safety:
Children (ages eight and below) and people with reduced physical, sensory or mental capabilities or
lack of experience and knowledge should be supervised when operating (or in the vicinity of) this
device.
DUAL MOTOR DESK ASSEMBLY MANUAL
CORRECT DISPOSAL OF THIS PRODUCT
This marking indicates that this product should not be disposed of with
normal household waste. To prevent possible harm to the
environment or human health from uncontrolled waste disposal,
recycle it responsibly to promote the sustainable reuse of material
resources. Please dispose of at a metal recycling center or contact
AnthroDesk to recycle your device responsibly.

2 1
2
4
5
3
3
NO
1
2
3
4
5
QTY.
1
2
2
1
1
INSTALLATION INSTRUCTION
CHECKLIST
A (4pcs) B (8pcs) C (12pcs) D (2pcs)
E (2pcs) F (Installation Tool)
M6x12mm M8x20mm ST5.0x23mm
(optional)
ST4.2x16mm
ST3.5*16

INSTALLATION INSTRUCTIONS
1
2
1
2
2
CAREFUL! DO NOT CRIMP THE CABLE

A
F
INSTALLATION INSTRUCTIONS
3
4
A (4pcs)
M6x12mm
TIGHTEN THE SCREWS

3
B
B
B
B
B
B
3
F
1
INSTALLATION INSTRUCTIONS
5
6
LOOSEN
B (8pcs)
M8x20mm
C (12pcs)
ST5.0x23mm
(optional)
C
CC
C
C
CC
CC
C
C
C

EE
DD
4
LEFT OR RIGHT
4
5
INSTALLATION INSTRUCTIONS
7
8
D (2pcs)
ST4.2x16mm
E (2pcs)
ST3.5*16
PLUG IN
LEFT OR RIGHT
5

Limited Height Setting:
Press the and keys for 5 seconds until you hear a beeping sound
indicating that the height has been limited (minimum limited height 96, maximum
limited height ＞ 97).
To cancel the limited height function, press the and again for 5 seconds;
when you hear the beeping sound, the limited height setting has now been
canceled.
Press
Home Key
Press
Home Key
Press
Home Key
Press
Home Key
Use or to adjust the base height.
DIRECTIONS FOR USE
Press the "HOME" key for
10 seconds until digital
screen displays "S1", then
press UP or DOWN key to
select S1 to S8
Click "HOME" key to go back to settings
0 - Disable
1
2
3
4
5
6
7
8
0.5°
1.0°
1.5°
2.0°
2.5°
3.0°
3.5°
4.0°
Press
Home Key
Press
Home Key
Press
Home Key
Press
Home Key
0 CM
1 Inch
0 Disable
1 The least sensitive
8 The most sensitive
0 Disable
1 The least sensitive
8 The most sensitive
0 Disable
1 The least sensitive
8 The most sensitive
0 Long press while desk is runnning until it stops
1 Click while the desk is running, second click to stop.
0 Disable (not recommended)
1 Turn on (with continous operation for 2 minutes, error
HOT will display)
S-1
Changing Between Metric
and Imperial Measurements
S-2
Anti-Collision Sensitivty
(overall sensitivity
adjustment)
S-3
Up Anti-Collision Sensitivity
(sensitivity detection)
S-4
Down Anti-Collision Sensitivty
(sensitivity detection)
S-5
Base Height
S-6
Memory Key Operation
S-7
Overheating Protection
S-8
Desktop Tilt Angle Setting
(Error E08 will display when
greater than selected degrees)

When "RST” is on the display screen, press the button until the desk frame reaches its lowest point. After hearing the
beeping sound and desk frame completes a height readjustment, initialization is completed. (IMPORTANT: The button must be
held during this process, if it is released prematurely, initialization will fail)
Forced initialization: Press the button until the desk frame reaches its lowest point, then release the button and press it
again for about 5 seconds until hearing the beep sound, the desk frame readjusts, and the initialization is completed.
Restore the factory settings: When a new controller is exchanged, or the parameters need to be restored to the factory settings,
press the and buttons simultaneously; you will hear the first beep sound after about 5 seconds and the second beeping
sound after 10 seconds. When the display screen shows "RST," please re-initialize as per step #1 above.
MEMORY KEYS (M1/M2)
After setting memory keys, the desk can lift automatically to the set memory height.
HOW TO SET MEMORY MODE: Please hold the desired M1/M2/M3/M4 key for 5 seconds until you hear a beep sound, and the
memory height is successfully saved. Then touch M1/M2/M3/M4 lightly, and the desk will move to that memory height automatically.
SET KEY (HOME)
Press the "HOME" key when internal parameters need to be set (see page 8 for more details). Click "HOME" to run to 72cm.
INITIALIZATION
1.
2.
3.
COLLISION SAFETY FUNCTION
The desk will stop and readjust height when the desktop is rising or lowering and encounters resistance.
ERROR CODES AND SOLUTION
Error Code
Fault Cause
Solution
E01,E06,E07
Power fault
Try another outlet or power source
E02
Synchronous height over 1cm
Implement the initialization operation 1
E04
Handset fault
Unplug and plug the handset back in
E05
Anticollision alert
Readjustment notification (normal operation with collision detection)
E08
Tabletop sloping
Check the tabletop
E11,E21,E40,E41
Connection cable failure
Check the connecting cable
E12,E22,E42,E43
Controller fault
Replace controller/handset
E13,E23
Motor 1 or 2 is out of open-phase
Check the motor wiring
E14~E17,E24~E27
Motor fault
Replace motor
E18,E28
Overloading
Reduce the desk load
HOT
Overtime operation
Automatic recovery after 20 minutes
UP and DOWN Key Display Screen Memory Key Home Key
DIRECTIONS FOR USE
The entire hand controller is a capacitive touch-sensitive
operation panel (only a gentle touch with your finger is
needed). After 10 seconds of inactivity, the display will
turn off and sleep. You can press any key to wake the
screen. After the display is on, you can continue to use it.
DISPLAY SCREEN
Display the height of the desk.
Please keep pressing UP/DOWN key to adjust desk height until
you get the desired height.