ANTIFERENCE HDMISS04 User manual

HDMISS04
1x4 HDMI 2.0a Splitter with EDID Management
& Auto Scaling 4K/1080p
User Guide

Important Safety Notice
Thank you for purchasing this Antiference HDMI distribution product. Please
read the following instructions carefully and retain for future reference.
Please pay careful attention to the following safety considerations:
1. Do not place any items on the device
2. Ensure no liquids are on or near the device as splashes may damage the unit
3. For cleaning, use a damp cloth only without solvents
4. Do not attempt to open the case as there is a danger of electric shock
5. Repairs should be carried out by a qualied technician
6. Place the unit in a well ventilated area to prevent overheating
7. Carry out the installation before connecting the device to a source of power
8. Use only the supplied power supply as 3rd party products may damage the product
Introduction
The HDMISS04 is a 1 to 4 HDMI 2.0a Splitter with auto scaling 4K/1080p. In addition,
the device supports HDCP 2.2, HDR and also features an EDID Management system
for complete exibility.
The auto scaling feature enables the user to connection a combination of 4K & 1080p
TV sets and the splitter automatically scales to the highest resolution the TV set is
capable of.
The splitter is compatible with SKY Q and is a perfect choice when connecting a
combination of different TV sets to the SKY box.
With built-in USB rmware update mechanism, the compatibility among many HDMI
sources and receivers can be further guaranteed. With full HDR/4K2K@60 4:4:4 8bits
and high denition audio support, the HDMISS04 is suitable for high quality HDMI
broadcasting, digital signage and education applications.

Features
• HDMI2.0a compliant
• Supports 4K2K@60 4:4:4 8bits
• Supports HDR1, which is 4K2K@60 4:2:0 10bits2
• HDCP 2.2 and 1.4 compliant
• Wide frequency range: 25MHz~600MHz
• Video bandwidth: 18Gbps
• Supports resolution downscaling from 4K2K to 1080P!
• Supports default EDID and EDID learning from display
• Supports xvYCC, x.v.Colour & Deep Colour
• Micro-USB rmware update for expanding compatibility
• Supports Dolby Digital, DTS-HD and Dolby TrueHD audio
• Simple installation
Package Contents
1x HDMISS04
1x DC 5V PSU
1x User Guide

Panel Description
1. Power LED: Lit up when device is receiving power
2. Micro-USB Port: Connect to 5V DC power supply unit
3. EDID Management System: See table below
4. Signal LED: Input signal LED indicator
5. HDMI IN: Connect to an HDMI input source
6. Signal LED: Output 1-4 signal LED indicator
7. HDMI OUT 1-4: HDMI outputs to HDMI displays [HDMI OUT1: EDID Learn
Default]
*Automatic EDID learning will detect all the connected HDMI equipped monitors and
analyze all the content of EDID. The EDID with maximal resolution support will be the
reference EDID for incoming HDMI source players.

Hardware Installation
1. Start with all devices including EDUs (TVs) powered off.
2. Connect the EDU devices.
3. Connect an HDMI source (such as a Blu-ray and SKY Q) to the HDMI input.
4. Plug in 5V DC power supply.
5. Power on the HDMI EDUs.
6. Power on the HDMI source.
Connection Diagram

Advanced Options
Troubleshooting
1. If for some reason there is no video output, try adjusting the EDID dip switch to
“[pin1, pin2]=[ ↑-↓]” or “[pin1, pin2]=[↓-↓]”.
Under “[pin1, pin2]=[↑-↓]”, there should be video output. The only requirement in this
setting is that the display must support at least Full HD 1080p. If the default Full-HD
EDID as described still doesn’t work then switch to “[pin1, pin2]=[↓-↓]” to learn the EDID
from output 1 to customize the EDID information. (Please note that the display with
lowest resolution must be connected to output 1)
Select to [pin1, pin2]=[↑-↓] - Full-HD(1080p@60) – 12bit 3D video & 7.1ch audio
1) Set the dip switch to “[pin1, pin2]=[↑-↓]”
2) Power on the device
Select to [pin1, pin2]=[↓-↓] – Learning EDID from output 1
1) Set the dip switch to “[pin1, pin2]=[↓-↓]”
2) Power on the device
3) It will automatically learn EDID from output 1
EDID Mode Note
a. If the user wants to change EDID mode, please power cycle the device after
setting the dip switches to the required positions.
Firmware Updates
2. Firmware update can be updated through the Micro-USB.
1) Save the rmware le (.bin) & software into the same folder.
2) Connect the Micro-USB cable between PC and device
3) Open the rmware update software and then device will start to update the rm
ware automatically.
4) After the update process is done, the software will show the “Success” message
and then will close automatically.
5) Power cycle the device to complete the process.

Specications
Technical
Role of usage 1x4 Distribution Amplier (Splitter)
HDMI compliance HDMI 2.0a
HDCP compliance HDCP 2.2 / 1.4
Video bandwidth Single-link 600MHz [18Gbps]
Video support HDR 4K2K@60(4:2:0 10bits) / 4K2K@60 (4:4:4 8bits)
Audio support DTS-HD Master Audio, Dolby TrueHD Dolby Digital,
DTS, LPCM
ESD protection Human body model — ±15kV [air-gap discharge] & ±8kV [con-
tact discharge]
Firmware update Feasible via Micro-USB port
Input 1x HDMI
Output 4x HDMI
HDMI connector Type A [19-pin female]
Dip switch EDID Mode selection
Mechanical
Housing Metal enclosure
Dimensions
[L x W x H]
Model 112 x 62 x 18mm[4.4” x 2.4” x 0.7” ]
Package 198 x 137 x 74mm [7.8” x 5.4” x 2.9”]
Carton 420 x 400 x 300mm [1’4”x 1’3” x 11.8”]
Weight Model 170g[6 oz]
Package 365g[12.9 oz]
Fixedness Wall-mounting case
Power supply 5V 1A DC
Power consumption 4 Watts [max]
Operation temperature 0~40°C [32~104°F]
Storage temperature -20~60°C [-4~140°F]
Relative humidity 20~90% RH [no condensation]

Declaration of Conformity
We, ANTIFERENCE LIMITED herewith declare that the HDMI splitter complies with all es-
sential requirements and any other applicable conditions set forth on directive 2014/30/EU.
According to the WEEE (Waste Electrical and Electronic Equipment) EU Directive, do
not dispose of this product as household waste or commercial waste. Waste Electrical
and Electronic Equipment should be appropriately collected and recycled as required by
practices established for your country. For information on recycling of this product, please
contact your local authorities, your household waste disposal service or the shop where
you purchased the product.