Antrica ANT-35000 User manual

ANT-35000- Quick Start Guide
Additional support may be found at: !
http://antrica.freshdesk.com
Antrica Quick Start Guide
ANT-35000
Page !1

Contents!
1 Whats in the box
2 Setting up the ANT-35000
3. Configuring the ANT-35000
3.1 Video Information
3.2 Video Encode
3.3 Network & IP Port
4. Streaming
4.1 RTSP over TCP to VLC player
4.1.1 How to configure VLC
4.2 MPEG Transport Stream to VLC
4.3 How to open an RTMP stream
5. Help and Further Support
Antrica Quick Start Guide
ANT-35000
Page !2

1.What’s in the Box
The ANT-35000 box contains
- ANT-35000 encoder
-12 Volt Power converter (requires an IEC AC mains lead)
-UK/EU/USA or China IEC 110/240v AC Lead (depending on your location)
-Fixing brackets
2. Setting up the ANT-35000
Connect the ANT-35000 to a laptop or PC using either a cross over ethernet cable or
via an Ethernet switch using standard ethernet cables.
Connect the input Video source using an HDMI HD-SDI or composite video cable.
Connect the 12 volt power input plug with IEC mains cable plugged in and switch on.
The ANT-35000 will take approximately 2 minutes to boot up. You will see 4 static or
flashing LEDs when boot up is complete.
You are now ready to setup the ANT-35000 Encoder
3. Configuring the ANT-35000
The ANT-35000 default IP address is 192.168.10.100 . Please set the laptop/PC
Ethernet IP address to be in the same sub-domain e.g 192.168.10.XXX
Open Internet Explorer (this will allow video to be viewed) or other browser to just
view setting and browse to 192.168.10.100
You will be asked to LOGIN:
Default User is: admin and Password: 1234
This is the first screen: Note the setup button top left. Please click this
Antrica Quick Start Guide
ANT-35000
Page !3
SETUP

!
3.1 Video Information
The Video Information page shows if a valid video signal is connected and gives
information about the stream settings
3.2 Video Encode:
This page allows you select which video input to use and to setup the stream
resolution , frame rate and so on
Antrica Quick Start Guide
ANT-35000
Page !4
Input format
Input format!
Detected
Primary
Stream settings

3.3 Network- IP & Port:
This section allows you set the encoder IP address and other network items
Antrica Quick Start Guide
ANT-35000
Page !5
Network
Settings

4.Streaming :
This section explains how to stream the following formats to VLC player as an
example player. Settings may vary with other players
4.1 RTSP over TCP to VLC player:
RTSP streaming only requires one setting to be changed in the ANT-35000. This is
the RTSP port which can be found under Network-IP&Port. By default this Port 554
The ANT-35000 RTSP URL is as follows:
rtsp://<IP ADDRESS>:<PORT>/video1 (video only streaming of primary stream)
rtsp://<IP ADDRESS>:<PORT>/video1s (video only streaming of 2nd stream) !
rtsp://<IP ADDRESS>:<PORT>/video1s1 (video only streaming of 3rd stream)
rtsp://<IP ADDRESS>:<PORT>/video1s2 (video only streaming of 4th stream)
If audio is required the URL adds +audio1
e.g rtsp://<IP ADDRESS>:<PORT>/video1s1+audio1s1 (video + audio streaming of
third stream) the audio URL extension always follows the video URL
Primary 2nd, 3rd and 4th steams are setup in the Video Encode section.
4.1.1 How to Configure VLC Player
Open VLC player and select FILE / OPEN NETWORK . Note the input windows in
VLC may vary depending on which operating system you are running VLC on.
This example is the MAC OS X Version of VLC player.
Antrica Quick Start Guide
ANT-35000
Page !6

Type in the RTSP URL with Port number as shown in this example:
rtsp://192.168.10.100:554/video1+audio1
Click OPEN…you should see the video stream displayed
NOTE! In advanced settings you will find VLC has a default buffer setting of 1000mS
this can be lowered to reduce latency to around 100-200mS
4.2 MPEG Transport Stream over UDP
To stream MPEG TS first we need to setup ONE WAY STREAMING in the
ANT-35000 which can be found under NETWORK-One way streaming.
Select MPEG TS and click Apply . Here you can select and Enable any or all of the 4
streams. There are two settings:
Antrica Quick Start Guide
ANT-35000
Page !7

IP Address: This is either the destination Unicast IP address of the computer on
which VLC is running or the multicast IP address you wish to use.
Port: This is the port you wish to use for streaming
Note! If you want to stream over the internet you must use the single Public IP
address of the building in which the computer, running VLC, is located. The Router in
this building will need to PORT FORWARD this stream( port number chosen above)
to the internal IP address of the computer. More later on Port Forwarding and Router
setup.
4.2.1 Open an MPEG-TS stream in VLC
Open VLC and open File/Network Please note the unicast URL has no IP in it.
Example URL for MPEG Transport Stream
udp://@:1234
udp://@227.2.2.7:1234
4.3 Open an RTMP stream
To stream RTMP you will need to know two pieces of information:
RTMP URL : example rtmp://wowza.antrica.com:1935/live/
Stream Name: streamdemo
Complete URL would then be
rtmp://wowza.antrica.com:1935/live/streamdemo
Antrica Quick Start Guide
ANT-35000
Page !8

Examples of players will be WOWZA media server or Youtube live streaming . Both
of these players can e setup to generate the full URL
Full URL= [Primary server URL:Port]/[Stream name]
5.0 Help and Further Support
Please visit http://antrica/freshdesk.com where you can find:
- application notes
- User manuals
- FAQs
- Firmware
- Other useful information
- Open up a Technical Support Ticket
Contact: [email protected]
Call : [phone]
Antrica Quick Start Guide
ANT-35000
Page !9