ANTUMBRA FADE User manual

ANTUMBRA
FADE
MANUAL

TABLE OF CONTENTS
01. INSTALLATION 4
02. BACK 5
03. FRONT 6
04. USE 7
05. LINK 8
06. BILL OF MATERIALS 9
07. BUILD NOTES 10
08. BACK 11
09. FRONT 14
10. MODIFICATION 15
11. FINISHED 16

00. THANK YOU!
Thank you for purchasing the Antumbra FADE module!
In this documentation you can find information about the
installation and use of the module, also an assembly in-
struction if you got your hands on the DIY version.

01. INSTALLATION
POWER CABLE HEADER
When you turn the FADE around, you should see the mod-
ule as it is on the left illustration. If this is your first FADE
module, connect a 10 pin header to the top row, where you
see the MAIN POWER text. Pay attention to the orienta-
tion of the cable, the RED STRIPE should be on top!
By doing otherwise you can potentially harm the module
or even your whole system! Power off your Eurorack sys-
tem and connect the other end of the cable to the power
source, here also pay attention to the PSU manufacturer’s
instructions!
TL072CD
LME49720
LME49720
104
104
104
104
104
104
104
104
104
102
102
103

02. BACK
LINK CABLE HEADER: Link two or more FADEs with a 16 pin
ribbon cable to send it’s output to the next FADE module.
You have to connect the LINK cable of the first unit to the
power header of the second unit, and so forth.
JUMPERS:
JP3 selects the voltage range, the bottom position is 10V
the top is 5V.
JP3 & JP4 selects the module’s orientation. The jumpers
are pointing to the bottom of the module, so if you want
to flip it, just put them both in the other position.
Both jumpers should be on either top or bottom position
at the same time.
TL072CD
LME49720
LME49720
104
104
104
104
104
104
104
104
104
102
102
103
TL072CD
LME49720
LME49720
104
104
104
104
104
104
104
104
104
102
102
103
TL072CD
LME49720
LME49720
104
104
104
104
104
104
104
104
104
102
102
103
POWER

03. FRONT
INPUT • OUTPUT
BIPOLAR • UNIPOLAR SWITCH
FADER (who knows)

04. USE
One FADE in itself can be used as an:
• Attenuator
• Offset generator
• Manual CV source
• Inverter
When there’s no input source connected, the set voltage
(on the back, 5/10V) is normalized to the input, this way
you can use it to generate CV in itself. The LED corre-
sponds to the activity of the output, green is positive,
red is negative voltage. If you switch to BIPOLAR mode,
0V will be in the center of the fader, down is negative
voltage, up is positive.
When you connect an input source you can attenuate it
with the fader.

05. LINK
FADE gets more interesting if you LINK more units, this
way you can mix signals together, or offset them easily.
To mix signals, insert a cable in the output of only the last
unit you want in the chain, this breaks the normalization
and the signal won’t appear further down the chain. You
can set up a master volume by connecting the output of
the module before the last one to the last one’s, so that
the last fader attenuates the mixed signal.
If you connect an input source in unit 1, and no input to
unit 2, you can use unit 2 as an offset for the signal, great
for LFOs, envelopes, etc.
IN1 IN4
OUT
IN4 OFFSET
IN2 IN3
OUT
MIX

06. BILL OF MATERIALS
QTY PART
2 1K RESISTOR (0603 SMD • 1%)
1 10K RESISTOR (0603 SMD • 1%)
9 100K RESISTOR (0603 SMD • 0.1% • THIN FILM)
6 100NF CAPACITOR (0603 SMD • >= 16V)
1 22PF CAPACITOR (0603 SMD • <= 2%, >= 25V)
2 10UF ELECTROLYTIC CAPACITOR (SMD • >= 25V)
2 1N5819HW DIODE (SOD123)
1 LM4040 (SOT23 • 10V)
1 TL072 DUAL OP-AMP (SOIC8)
2 LME49720 DUAL OP-AMP (SOIC8)
1 LM321MF (SOT23-5)
1 SLIDE POT (B10K)
1 LED (3MM • RED/GREEN • 2 TERMINALS)
2 2X8 MALE HEADER (2.54MM LEAD SPACING)
3 1X3 MALE HEADER (2.54MM LEAD SPACING)
QTY PART
3 JUMPER (2.54MM LEAD SPACING)
1 10MM SPACER
2 THONKICONN JACK
2 M3X5 SCREW
1 SLIDE POT KNOB
DETAILED EXCEL SHEET WITH PART NAMES, NUMBERS
AND LINKS: HERE
MOUSER CART: HERE
NOTE: jacks, screw and pot knob is not included in the
cart! See the excel sheet about these.

07. BUILD NOTES
Before you start building look through the build manual
so that you’ll be familiar with the building process and
you won’t run into any surprises! :)
Good luck!