Anyload PS805 User manual

PS805
Thermal Receipt Printer
User Manual
Safety Notice:
* Read this manual before operate and/or connect the printer.
* Don't touch the printer head with hard objects.
* Don't touch the cutter blade.
* Don't bend the power cord excessively or place any heavy objects on
it.
* When connecting or disconnecting the plug, always hold the plug, not
the cord.
* Keep the printer out of children's reach.
* Use only approved accessories and do not try to disassemble, repair or
remodel it.
* Place the printer on a stable surface. Choose firm, level surface
to avoid vibration.
* Don't let water or other foreign objects go inside the printer.
* Don't connect a telephone line into the peripheral drive connector.
* We suggest you unplug the printer from the power outlet if not in use
for a long period.
* If there is a paper jam, switch off and unplug the printer, wait for 10
seconds to let the printer head cool down before remove the paper.
* Do not place in a humid and/or dusty environment.
* Only use appropriate paper roll.
* Don't use paper rolls with end-of-roll glued on the reel. The printer
might not able to track the end and might damage the printer.
* Don't use paper rolls without reel either. It might cause paper jam due
to not enough weight when running close to the end of the roll.
*
*
*
*
*
*
*
*
Main Features:
* Plug-and-play, user friendly.
* Low-noise thermal printing.
* Easy paper-roll installation.
* Easy paper jam clearance.
* Easy maintenance for tasks such as head cleaning.
2
V090319
PS805

Contents
Chapter 1 Before You Start
1.1 Checking What's in the Box
1.2 Learn about the Printer
Chapter 2 Connecting the Printer
2.1 Connect the Cables
2.2 Install Paper Roll
Chapter 3 Maintenance
3.1 Cleaning the Printer Head
3.2 Cleaning the Paper Scraps
3.3 Handling the Printer
Chapter 4 Operating the Printer
4.1 Turn the Printer On or Off
4.2 Keys & Indicators on Front Panel
4.3 Error Signal
4.4 Printing & Tear off Position
Chapter 5 Specifications
3
4
6
8
10
5
6
9
10
9
11
11
Chapter 6 Communication Interface
6.1 Printer 13
15
6.2 Connect to 805TS Indicator
Chapter 1 Before You Start
1.1 Checking What's in the Box
PS805 Thermal Receipt Printer
Power Cable Power Adapter
User Manual
4
Interface Cable
PS805
PS805
Thermal Receipt Printer
User Manual
PS805

Chapter 2 Connecting the Printer
2.1 Connect the Cables
2.2 Install Paper Roll
Connect the Interface CableConnect the Power Cable
Place the thermal paper roll
as shown in the above figure.
Open the top cover
by lifting the handle.
Please make sure the power cord is unpluged and the computer
connected with the inteface cable is turned off.
6
1.2 Learn about the Printer
Power Line
RJ-11
Base
Cover
Cover Opening Handle
Power Indicator
[LF] Key
[SEL] Key
Status Indicator
Paper Output Slot
On/Off Switch
Interface Cable
(to 805TS Indicator)
5
PS805

2.2 Install Paper Roll (Con't)
Close the cover firmly.
Then press the [SEL] key
to make it on-line.
The Printer won't work probably
if you reversed the paper roll.
Note:
* Only use high quality thermal paper roll with appropriate size
and specification.
* Paper roll that is too wide or too narrow might cause paper jam.
* Use low quality thermal paper roll might result in poor print out
and/or reduce the life of the printer head.
* Don't press the [LF] key when out of paper to prevent damage
to the printer head.
* Don't pull the paper out by hand.
* Please close the top cover gently.
*
*
*
7
PS805
Chapter 3 Maintenance
3.1 Cleaning the Printer Head
After using the printer for a period of time, the print out might be
fade or not clear. In this case, a clean up maintenance is
required.
1. Please make sure the power cord is unplugged and the
interface cable is disconnected.
2. Open the top cover, remove the paper roll from the printer.
3. Wait for 10 seconds to let the printer hand cool down naturally.
4. Use a cotton swab, dip with alcohol and wipe the printer head
gently.
4. Wait until the alcohol on the printer head completely
evaporated, reload the thermal paper roll, close the cover and
reconnect all cables.
5. Check if the print out has improved.
6. Repeat the above steps if necessary. If the problem persist,
1.
1.
1.
1.
Never use sand paper, cutter, screw driver or any hard object to
scratch the printer head to prevent permanent damage to the
printer head.
Printer Head
Cleaning Zone
8
PS805

3.2 Cleaning the Paper Scraps
After using the printer for a period of time, paper scraps will
accumulate around the printer head area. Paper scraps felt into
the gears might result in damaging the gear system. Therefore,
regular clean up is required.
1. Please make sure the power cord is unplugged and the
interface cable is disconnected.
2. Use a soft brush to clean up paper scraps around the cutter
blade.
3. Open the top cover, remove the paper roll from the printer.
4. Use air brush to blow away the paper scraps on the gear
system. Use soft brush to remove paper scraps around the
printer head.
1.
1.
1.
1.
Note:
* Recommend to do the paper scraps clean up twice a month. If
using low quality thermal paper roll and/or using the printer very
often, can process the clean procedure more frequently.
3.3 Handling the Printer
Use both hand to hold the base Never lift by holding
the top cover
9
PS805
On/Off Switch
Chapter 4 Operating the Printer
4.1 Turn the Printer On or Off
After the power cable are plugged in and connected with the
power adapter. The printer can be turn on or off by the switch at
the back.
On/Off-line: Switch on or off by pressing the [SEL] key once.
On-line: Green indicator light is on.
Off-line: Green indicator light is off. Printer will not accept any
data. Press [LF] key will run the paper.
Power On: Red indicator light is on.
Power Off: Red indicator light is off.
4.2 Keys & Indicators on Front Panel
[SEL] Key
[LF] Key
Red Light
Green Light
10
PS805

4.3 Error Signal
A flashing green light on the front panel is an error signal. The
flashing frequency indicates different error message:
Signal
-.-.-
--.--.--
---.---.---
Error Message
Out of paper
Printer head over heat
Thermal printer head
resistance error
Suggestion
Replace paper roll.
Wait until temperature of
printer head drop to 45 C
will resume automatically.
Non-recoveable. Please
send for repair. Usually due
to cable connection error.
o
4.4 Printing & Tear off Position
The distance between the tear off position and the printing
position is 12mm.
ANYLOAD TRANSDUCER
Date: 13-03-2009
Gross: 33.88lb
Printer Head Position
Tear off Position
12mm
Paper Run
Direction
11
Chapter 5 Specifications
Print Method:
Paper Roll Width:
Paper Roll Diameter:
Paper Thickness:
Effective Print Width:
Print Density:
Print Speed:
Paper Rolling Speed:
Printer Power Input:
Working Environment:
Storage Environment:
Reliability (MCBF):
Printer Net Weight:
Dimensions:
Thermal Line Printing
57.5 +/- 0.5mm
Max. 50mm; Min. Ф13mm (w/reel)
60~70um; 53~60g/m
48mm
8 pt/mm; 384 pt/line
50mm/second
50mm/second
DC 9~12V, 2A
0~50°C; Dampness 20~85%
-20~60°C; Dampness 5~95%
10 X 10 Line
1.0Kg
116 (W) X 185 (D) X 140 (H) mm
Ф
2
6
(When 34°C, Humidity 85%)
(When 40°C, Humidity 58%)
≤
≤
12

Chapter 6 Communication Interface
6.1 Printer
- RS232C comparable
- Support RTS/CTS and XON/XOFF
- 25-pin female D
Pin
3
2
4
7
Signal
RXD
TXD
RTS
GND
Description
Printer receive data from computer.
When requesting printer status
command, printer transmit status
signal to computer.
"MARK" = printer busy, cannot
receive data; "SPACE" = ready, can
receive data.
Ground
Source
Computer
Printer
Printer
—
PS805 printer can connect with standard RS232C with PC:
Printer
25-pin
base
PC
DB-9
Printer
25-pin
base
PC
DB-25
13
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16~17
18~25
Signal
/STB
Data1
Data2
Data3
Data4
Data5
Data6
Data7
Data8
/ACK
BUSY
PE
SEL
NC
/ERR
NC
GND
Description
Direction
In
In
In
In
In
In
In
In
In
Out
Out
Out
Out
—
Out
—
—
14

6.2 Connect to 805TS Indicator
15