AnyTone D868UV User manual

A1.170722

D868UV
Instruction Manual
D

THANK YOU!
Thank you very much for choosing our Dual Band DMR two way radio. This simple to use
radio adopts the latest advances in technology, providing reliable communication in today’s demanding
communication environment.
This radio have both DMR digital and analog communication, introduces innovative DMR digital
processing system to achieve SMS, high-audio quality and digital encryption. It boasts novelty, best
stability, great reliability, nice timbre and long distance communication as well as fashionable design
and smooth exterior lines. D868UV has Text message, recording, voice message, digital encryption,
emergency alarm, Man down alarm, lone work, GPS, Vibration and Analog DTMF, 2TONE, 5TONE,
CTCSS/DCS encode/decode functions.
NOTE:
When programming the radio, read the factory initial data first, then rewrite the frequency and
signaling etc., otherwise errors may occur because of different frequency band etc.
You can use the programming cable to program the frequency, channel type, power etc. which are
comply with the FCC certification.
You can't change RF parameter（eg. RF power , Fre Range） by programming software.

Notice to the User
1. Keep the radio and accessories away from children.
2. Please do not try to open or modify the radio without permission, non-professionals process may
cause damage.
3. Please use assorted battery and charger to avoid damages.
4. Please use assorted antenna to ensure the communication distance.
5. Please do not expose the radio to direct sunlight for a long time nor place the radio near any heat
devices.
6. Please do not put the radio in extremely dusty or humid areas.
7. Do not use harsh chemicals, cleaning solvents to clean the transceiver.
8. Do not transmit without antenna.
9. When using this radio, we recommend transmitting for 1 minute then receiving for 4 minutes.
Continuous transmitting for long time or working in high power will heat the back of the radio. Do not
place the radio’s hot side close to any surface of plastic.
10.If any abnormal odor or smoke detected coming from the radio, cut off the power and take off the
battery pack. Then contact local AnyTone dealers.
ATTENTION:
All tips above apply to accessories of your AnyTone two way radio. If any device can not work normally,
please contact local AnyTone dealers.
If you use any accessories made by other companies, AnyTone company does not guarantee the
operability and safety of the radio.

Unpacking and Checking the Equipment
Unpack the radio carefully. We recommend that you identify the items listed in the following table before
discarding the packing materials. If any items are missing or have been damaged during shipment,
please contact the carrier or the dealers immediately.

SAFETY TRAINING INFORMATION
our Qixiang Electron Science& Technology Co., Ltd radio generators RF electromagnetic
during transmit mode.This radio is designed for and classified as"Occupational Use Only",
meaning it must be used only during the course of employment by individuals aware of the
hazards,and the ways To Minimize Such hazards. This radio is NOT intended for use by the"General Population"
in an uncontrolled environment. This radio has been tested and complies with the FCC RF exposure limits for
"Occupational Use Only".Inaddition, our Qixiang Electron Science& Technology Co., Ltd radio complies with the
following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation
of such levels for exposure to humans:
--IEEE Std. 1528:2013 and KDB447498, Evaluating Compliance with FCC Guidelines for Human
Exposure to Radio Frequency Electromagnetic Fields.
--American National Standards Institute (C95.1-1992), IEEE Standard for Safety Levels with Respect to
Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz.
--American National Standards Institute (C95.3-1992), IEEE Recommended Practice for the Measurement
of Potentially Hazardous Electromagnetic Fields- RF and Microwave.
The information listed above provides the user with the information needed to make him or
her aware of RF exposure, and what to do to asÿsure that this radio operates with the FCC RF
exposure limits of this radio.

Electromagnetic Interference/Compatibility
During transmissions, Qixiang Electron Science& Technology Co., Ltd radio generates RF energy that can
possibly cause interference with other devices or systems. To avoid such interference, turn off the radio in
areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to
electromagnetic radiation such as hospitals, aircraft, and blasting sites.
Occupational/Controlled Use
The radio transmitter is used in situations in which persons are exposed as consequence of their employment
provided those persons are fully aware of the potential for exposure and can exercise control over their exposure.
Attention:
This radio complieswith IEEE and ICNIRP exposure limits for occupational/controlled RF exposure
emvironment at operating duty factors of up to 50% and is authorized by the FCC for occupational use only. An
appropriate warning lable is affixed to all units. In order to comply with RF exposure requirements, a minimum
distance of 2.5cm must be maintained when held-to-face, and body-worn operations are restricted to the approved
original acessories (belt clip). Do not use this device when antenna shows obvious damages
This product is compliance to FCC RF Exposure requirements and refers to FCC website
https://apps.fcc.gov/oetcf/eas/reports/GenericSearch.cfm search for FCC ID:T4KD868UV to gain further
information include SAR Values.

Professional
FM Transceiver 1
Supplied Accessories
Item Number Quantity
Antenna 1
Li-ion Battery Pack 1
Battery Charger 1
AC Adaptor 1
Belt Clip 1
Hand Strap 1
Instruction Manual 1

Professional
FM Transceiver
2
Standard Accessories
Antenna*1Li-ion Battery Pack
Li-ion Battery Pack
Charger AC Adaptor Belt Clip
Instruction
Manual
* Note: For frequency band of antenna, please refer to label indicated in
the bottom of the antenna.
* Note: Car Charger and QBC-44L Charger should be used together.
Optional Accessories
USB Programming
Cable
USB Programming
Programming Software
Earphone
Car Charger

Professional
FM Transceiver 3
Charging Operation
The battery pack is not charged at the factory; please charge it before use.
Charging the battery pack for the rst time after purchase or extended storage ( more than 2 months)
may not bring the battery pack to its normal operating capacity. After fully charging/discharging cycle
for two or three times, the operating capacity will reach its best performance. The battery pack life
is over when its operating time decreases even though it is fully and correctly charged. Replace the
battery pack.
Charger Applied
Please use the specic charger appointed by our company. Other models may cause explosion and
personal injury. After installing the battery pack, if the radio displays low battery with red ashing
lamp or voice prompt, please charge the battery.
Notice for Charging Battery
1. Do not short the battery terminals or throw the battery into fire. Never attempt to remove the
casing from the battery pack, we show no responsibility on any results caused by modifying freely
without permission of our factory.
2. The ambient temperature should be between 5℃~40℃while charging is in process. Charging
outside this range may not fully charge the battery.
3. Please turn off the radio before inserting it into the charger. Otherwise, it will interfere with correct
charging.
4. To avoid interfering the charging, please do not cut off the power or take out the battery during
charging.

Professional
FM Transceiver
4
WARNING: When keys, ornamental chain or other electric metals contact the battery terminal, the
battery may cause damage or hurt bodies. If the battery terminal short circuit it will generate a lot
of heat. Take care when carrying and using the battery. Remember to put the battery or radio into
insulated container. Do not put it into metal container.
How to Charge
1. Plug the AC adaptor into the AC outlet, and then plug
the cable of the AC adaptor into the DC jack located
on the back of the charger. The indicator lights
orange(1s) and then goes out---waits to charge.
2. Plug the battery or the radio into the charger. Make
sure the battery terminals are in contact with charging
terminals well. The indicator turns into twinkling red---
Pre-charging begins.
3. After pre-charging for about 5 minutes, the red
indicator will stop twinkling--- charging begins.
4. It takes approximately 2 hours to fully charge the
battery. When the lamp lights green, the charging is nished. Remove the battery or the radio unit
with battery from socket.
5. Do not recharge the battery pack if it is already fully charged. This may shorten the life of the
battery pack or damage the battery pack.
6. Do not charge the battery or the radio if it is damp. Dry it before charging to avoid danger.

Professional
FM Transceiver 5
NOTE: when charging a power-on radio equipped with battery, the indicating lamp will not turn
into green to show the fully charged status. Only when the transceiver is switched off, the lamp can
indicate normally. The radio consumers energy when it is power-on, and the charger can not detect
the voltage when the battery has been fully charged. So the charger will charge battery in constant
voltage and fail to indicate correctly whether the battery has been fully charged.
Charging Status Indicator Status
Standby (Self-examine lights orange 1second when power on) None
Pre-charging (Pre-charging stage) Red light twinkles for about 5 minutes
Charging (Charge in a constant current) Lights red for about 5 hours
Fully charged (Charge in a constant voltage) Lights green
STATUS Self-Examine
When Power on No Battery Pre-charging Charge
Normally
Fully
Charged Trouble
LED Orange
(for 1 second) None
Red Light
Twinkles
for 5 Minutes
Red Green Red twinkles
for a long time
NOTE: Trouble means battery heating, battery short-circuit or charger short-circuit.
5. Charging Process
6. LED Indicator:

Professional
FM Transceiver
6
Normal Charging Tips
1. Self- Examination: When charging, orange light twinkles for 1 second and goes out, which means
the charger has passed it self-examination and it can charge the battery normally. If the light remains
orange or the red light twinkles, it means the charger can not pass it self-examination or charge the
battery.
2. Trickle Pre-Charging: If red light twinkles when battery is inserted into the charger, it means the
remnant voltage is low and the charger is trickle-charging when the battery ( Pre-Charging Status).
The charger will automatically turn into normal charging when the battery reaches a certain electric
quantity, and if the red light stops twinkling, it means the remnant voltage meets s certain electric
quantity, the charger will charge the battery normally.
NOTE: Trickle charging ( Pre-Charging Status) time can not beyond 30 minutes. If the indicating
lamp still twinkles after 30-minute trickle-charging, it means that the charger can not charge the
battery. Please check whether the battery or charger is damaged.
How to Store the Battery
1. If the battery needs to be stored, keep it in status of 80% discharged.
2. It should be kept in low temperature and dry environment.
3. Keep it away from hot places and direct sunlight.

Professional
FM Transceiver 7
WARNING:
1. Do not short circuit battery terminals.
2. Never attempt to remove the casing from the battery pack.
3. Never assemble the battery in dangerous surroundings, spark may cause explosion.
4. Do not put the battery in hot environment or throw it into re, it may cause explosion.

Professional
FM Transceiver
8
Installing / Removing the Battery
1. Match the two grooves of the battery pack with the
corresponding guides on the back of the radio and
then push it.
2. To remove the battery pack, slide up the release
latch and remove the pack away from the
transceiver.
Installing / Removing the Antenna
■ Installing the Antenna:
Screw the antenna into the connector on the top of
the transceiver by holding the antenna at its base
and turning it clockwise until secure.
■ Removing the Antenna:
Turn the antenna anticlockwise to remove it.

Professional
FM Transceiver 9
Installing / Removing the Belt Clip
■ Installing the Belt Clip:
Place the belt clip to the corresponding grooves on the
back of the radio, and then clockwise screw it.
■ Removing the Belt Clip:
Anticlockwise turn the screws to remove the belt clip.
Installing the Additional Speaker/ Microphone (Optional)
Unveil the MIC-SP jack cover and then insert the
Speaker/Microphone plug into MIC-Sp jack.

Professional
FM Transceiver 10
Radio Overview
1
3
14
4
7
9
12
13
11
2
6
8
5
10

Professional
FM Transceiver
11
1Antenna
2Channel Switch
3POWER/VOLUME Switch
Turn clockwise to switch on the radio
Turn counterclockwise till a click is heard to switch off the radio.
Rotate to adjust the volume after turning on the radio.
4MIC Input
Please keep your mouth about 10cm away from the microphone to achieve the best voice quality
5Speaker
6LCD
Display the frequency/channel information, operation and status.
7Func key
Press to enter function menu set up;
Program the hot keys in PC software, press func, then press the hot key to perform the programmed
function.
8Exit Key
In standby, press the key to enter the Contact list.
In menu, press the key to return the last menu.
9P1 key/ P2 key
Programmable in PC software for different functions
10 Emergency Alarm Key
Programmable in PC software for other functions.
11 PTT (Push-To-Talk) Button
To make a call, press and hold the PTT button, then speak into the microphone. Release the button

Professional
FM Transceiver 12
to receive the signals.
12 [PF1]/[PF2] Key
Programmable in PC software for different functions.
13 Speaker/Microphone Jacks. PC program connector
14 Status Indicator
Indicate the different working status

Professional
FM Transceiver
13
Programmed Key
In PC software – Public - Optional Setting - Key function, it is able to set different functions for PF1,
PF2, PF3, P1, P2 keys.
OFF No Function
Voltage Check the current battery capacity voltage
Power Switch the power between super high, high, middle and low power.
Relay Switch between talk around and repeater mode
Invert Turn on/off the frequency reverse function.
Digital Encryption Choose the encryption group
Call In Analog channel, send the DTMF/5TONE/2TONE encode.
This function is only valid for analog channel.
TBST In Analog channel, send the tone pulse frequency signal to active the
repeater.
VOX Set up the VOX level
VFO/MR Switch between VFO mode and memory channel mode.
Sub PTT Sub channel PTT, press to start the call on sub channel
Scan Scan on/off
FM Radio FM radio on/off
Alarm Long press the key to start alarm, short press again to exit the alarm.
Record switch Enable/disable the recording function