AOC V19 User manual

١| Page
AOC MONITOR
USER`S GUIDE
V19+
SAFETY INTRODUCTION…………………………………………………………….2
SETUP…………………………………………………………………………………….4
ADJUSTING…………….…………………………………………………...……………7
DRIVER INSTALLATION GUIDE…………………….….…………………………..12
PRODUCT INFORMATION…………………………………………………………...18
TROUBLESHOOT……...………………………………………………………….…….19

٢| Page
SAFETY INTRODUCTION
The following subsections describe notational conventions used in this document.
Notes, Cautions, and Warnings
Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type.
These blocks are notes, cautions, and warnings, and they are used as follows:
NOTE: A NOTE indicates important information that helps you make better use of your computer
system.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you
how to avoid the problem.
WARNING: A WARNING indicates the potential for bodily harm and tells you how to avoid the
problem.Some warnings may appear in alternate formats and may be unaccompanied by an icon. In
such cases, the specific presentation of the warning is mandated by regulatory authority.
The monitor should be operated only from the type of power source indicated on the label. If
you are not sure of the type of power supplied to your home, consult your dealer or local power
company.
The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This
will fit only into a grounded power outlet as a safety feature. If your outlet does not accommodate the
e
-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance
ly. Do not defeat the safety purpose of the grounded plug.
Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will
e
ct the monitor from damage due to power surges.
Do not overload power strips and extension cords. Overloading can result in fire or electric shock.
To ensure satisfactory operation, use the monitor only with UL listed computers which have
r
opriate configured receptacles marked between 100 - 240V AC, Min. 5A
The wall socket shall be installed near the equipment and shall be easily accessible.
For use only with the attached power adapter (Output 12Vdc) which have UL,CSA listed license (Only
m
onitors with power adapter).
Do not place the monitor on an unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can
injure a person and cause serious damage to this product. Use only a cart, stand, tripod, bracket, or
table recommended by the manufacturer or sold with this product. Follow the manufacturer’s
instructions when installing the product and use mounting accessories recommended by the
manufacturer. A product and cart combination should be moved with care.
Never push any object into the slot on the monitor cabinet. It could damage circuit parts causing a
Do not place the front of the product on the floor.
Leave some space around the monitor as shown below. Otherwise, air-circulation may be

٣| Page
Clean the cabinet regularly with the cloth provided. You can use
soft-detergent to wipe out the stain, instead of
strong-detergent which will cauterize the product cabinet.
When cleaning, make sure no detergent is leaked into the
product. The cleaning cloth should not be too rough
as it will scratch the screen surface.
Please disconnect the power cord before cleaning the
product.
If the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIATELY and contact a Service
Center.
Make sure that the ventilating openings are not blocked by a table or curtain.
Do not engage the LCD monitor in severe vibration or high impact conditions during operation.
Do not knock or drop the monitor during operation or transportation.

۴| Page
SETUP
Not all signal cables (Analog, DVI, and HDMI cables) will be provided for all countries and regions. Please check with the local
dealer or AOC branch office for confirmation.
Please setup or remove the base following the steps as below.

۵| Page
Setup:
Remove:
For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's
angle to your own preference.
Hold the stand so you will not topple the monitor when you change the monitor's angle.
You are able to adjust the monitor's angle from -5° to 20 °.

۶| Page
NOTE:
Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen.
Cable Connections On Back of Monitor and Computer
1. Power
2. USB
3. Audio
4. Analog (DB-15 VGA cable)
5.HDMI
To protect equipment, always turn off the PC and LCD monitor before connecting.
1. Connect the power cable to the AC port on the back of the monitor.
2. To link the USB camera, please connect the LCD monitor and your PC with USB cable.
3. Connect the audio cable to audio in port on the back of the monitor
4. Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the
computer's D-Sub port.
5. (Optional – Requires a video card with HDMI port) - Connect one end of the HDMI cable to the back of
the monitor and connect the other end to the computer’s HDMI port.
6. Turn on your monitor and computer.
If your monitor displays an image, installation is complete. If it does not display an image, please refer
Troubleshooting.

٧| Page
Adjusting
The recommended resolution for this monitor is 1680 by 1050. To setup the monitor to this resolution, follow the steps below.
For Windows Vista:
1 Click START.
2 Click CONTROL PANEL.
3 Click Appearance and Personalization.
4 Click Personalization

٨| Page
5 Click Display Settings.
6 Set the resolution SLIDE-BAR to 1680 by 1050.
For Windows XP:
1 Click START.
2 Click SETTINGS.
3 Click CONTROL PANEL.

٩| Page
4 Click Appearance and Themes.
5 Double click DISPLAY.
6 Click SETTINGS.
7 Set the resolution SLIDE-BAR to 1680 by 1050.
For Windows ME/2000:
1 Click START.
2 Click SETTINGS.
3 Click CONTROL PANEL.
4 Double click DISPLAY.
5 Click SETTINGS.
6 Set the resolution SLIDE-BAR to 1680 by 1050.

١٠| Page
Luminance Contrast Brightness Eco mode Gamma DCR
Image Setup Clock Phase H.Position V.Position
Color Temp. Color Temp. User-R User-G User-B
Color Boost Full Enhance Nature Skin Green Field Sky-blue
A
utoDetect Demo
Picture Boost Frame Size Brightness Contrast H. position V.position
Bright
Frame
OSD Setup H.Position V.Position Timeout Transparence Language
Extra Input Select
A
uto Config Image Ratio DDC-CI Off Timer Information
Reset Reset
Exit Exit

١١| Page
Status LED Color
Full Power Mode Blue
A
ctive-off Mode Orange

١٢| Page
DRIVER INSTALLATION GUIDE
Windows 2000
1. Start Windows® 2000
2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'.
3. Double click on the 'Display' Icon.
4. Select the 'Settings' tab then click on 'Advanced...'.
5. Select 'Monitor'
- If the 'Properties' button is inactive, it means your monitor is properly configured. Please stop
installation.
- If the 'Properties' button is active. Click on 'Properties' button. Please follow the steps given below.
6. Click on 'Driver' and then click on 'Update Driver...' then click on the 'Next' button.
7. Select 'Display a list of the known drivers for this device so that I can choose a specific driver', then
click on 'Next' and then click on 'Have disk...'.
8. Click on the 'Browse...' button then select the appropriate drive F: ( CD-ROM Drive).
9. Click on the 'Open' button, then click on the 'OK' button.
10. Select your monitor model and click on the 'Next' button.
11. Click on the 'Finish' button then the 'Close' button.
If you can see the 'Digital Signature Not Found' window, click on the 'Yes' button.
Windows ME
1. Start Windows® Me
2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'.
3. Double click on the 'Display' Icon.
4. Select the 'Settings' tab then click on 'Advanced...'.
5. Select the 'Monitor' button, then click on 'Change...' button.
6. Select 'Specify the location of the driver(Advanced)' and click on the 'Next' button.
7. Select 'Display a list of all the drivers in a specific location, so you can choose the driver you want',
then click on 'Next' and then click on 'Have Disk...'.
8. Click on the 'Browse...' button, select the appropriate drive F: ( CD-ROM Drive) then click on the 'OK'
button.
9. Click on the 'OK' button, select your monitor model and click on the 'Next' button.
10. Click on 'Finish' button then the 'Close' button.
Windows XP
1. Start Windows® XP
2. Click on the 'Start' button and then click on 'Control Panel'.

١٣| Page
3. Select and click on the category ‘Appearance and Themes’
4. Click on the 'Display' Item.
5. Select the 'Settings' tab then click on the 'Advanced' button.
6. Select 'Monitor' tab
- If the 'Properties' button is inactive, it means your monitor is properly configured. Please stop
installation.
- If the 'Properties' button is active, click on 'Properties' button.
Please follow the steps below.

١۴| Page
7. Click on the 'Driver' tab and then click on 'Update Driver...' button.
8. Select the 'Install from a list or specific location [advanced]' radio button and then click on the 'Next'
button.

١۵| Page
9. Select the 'Don't Search. I will choose the driver to install' radio button. Then click on the 'Next' button.
10. Click on the 'Have disk...' button, then click on the 'Browse...' button and then select the appropriate
drive F: (CD-ROM Drive).
11. Click on the 'Open' button, then click the 'OK' button.
12. Select your monitor model and click on the 'Next' button.
- If you can see the 'has not passed Windows® Logo testing to verify its compatibility with Windows®
XP' message, please click on the 'Continue Anyway' button.
13. Click on the 'Finish' button then the 'Close' button.
14. Click on the 'OK' button and then the 'OK' button again to close the Display_Properties dialog box.

١۶| Page
Windows Vista
1. Click "Start " and "Control Panel". Then, double-click on "Appearance and Personalization".
2. Click "Personalization" and then "Display Settings".
3. Click "Advanced Settings...".

١٧| Page
4. Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means the
configuration for your monitor is completed. The monitor can be used as is.
If the message "Windows needs..." is displayed, as shown in the figure below, click "Continue".
5. Click "Update Driver..." in the "Driver" tab.
6. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of
device drivers on my computer".

١٨| Page
7. Click on the 'Have disk...' button, then click on the 'Browse...' button and then select the appropriate
drive F:\Driver (CD-ROM Drive).
8. Select your monitor model and click on the 'Next' button.
9. Click "Close" →"Close" →"OK" →"OK" on the following screens displayed in sequence.
PRODUCT INFORMATION
LCD Panel
Model number V19+
Driving system TFT Color LCD
Viewable Image
Size 481mm diagonal
Pixel pitch 0.243mm(H) x 0.243mm(V)
Video R, G, B Analog lnterface & HDMI
Separate Sync. H/V TTL
Display Color 16.7M Colors
Dot Clock 165 MHz
Resolution
Horizontal scan
range 30 kHz - 83 kHz
Horizontal scan
Size(Maximum) 408.24mm
Vertical scan
range 56 Hz - 75 Hz
Vertical scan
Size(Maximum) 255.15mm
Optimal preset
resolution 1680 x 1050 (60 Hz)
Highest preset
resolution 1680 x 1050 (60 Hz)
Plug & Play VESA DDC2B/CI
Input Connector D-Sub 15pin &HDMI
Input Video Signal
A
nalog: 0.7Vp-p(standard), 75 OHM, HDMI
Power Source 100~240VAC, 50/60Hz
Power
Consumption
Typical < 32 W
Standby < 1 W
Physical
Characteristics
Connector Type 15-pin Mini D-Sub &HDMI
Signal Cable Type Detachable
Dimensions &
Weight:
Height (with base) 398.1 mm
Width 460.2 mm
Depth 180 mm
Weight (monitor only) 2.9 kg
Weight (with
packaging) 5.67 kg
Environmental
Temperature: Operating 0° to 40°
Non-Operating -20°to 60°
Humidity: Operating 10% to 85% (non-condensing)
Non-Operating 5% to 80% (non-condensing)
A
ltitude: Operating 0~ 3000m (0~ 10000 ft )
Non-Operating 0~ 5000m (0~ 15000 ft )

١٩| Page
TROUBLESHOOT
Problem &
Question Possible Solutions
Power LED Is Not
ON
Make sure the power button is ON and the Power Cord is properly connected
to a grounded power outlet and to the monitor.
No images on the
screen
Is the power cord connected properly?
Check the power cord connection and power supply.
Is the cable connected correctly?
(Connected using the D-sub cable)
Check the DB-15 cable connection.
(Connected using the DVI cable)
Check the DVI cable connection.
* DVI input is not available on every model.
If the power is on, reboot the computer to see the initial screen (the login
screen), which can be seen.
If the initial screen (the login screen) appears, boot the computer in the
applicable mode (the safe mode for Windows ME/XP/2000) and then change the
frequency of the video card.
(Refer to the Setting the Optimal Resolution)
If the initial screen (the login screen) does not appear, contact the Service
Center or your dealer.
Can you see "Input Not Supported" on the screen?
You can see this message when the signal from the video card exceeds the
maximum resolution and frequency that the monitor can handle properly.
A
djust the maximum resolution and frequency that the monitor can handle
properly.
Make sure the AOC Monitor Drivers are installed (AOC Monitor Drivers are
available at : here)
Picture Is Fuzzy
& Has Ghosting
Shadowing
Problem
Adjust the Contrast and Brightness Controls.
Press to auto adjust.
Make sure you are not using an extension cable or switch box. We recommend
plugging the monitor directly to the video card output connector on the back .
Picture Bounces,
Flickers Or Wave
Pattern Appears
In The Picture
Move electrical devices that may cause electrical interference as far away from
the monitor as possible.
Use the maximum refresh rate your monitor is capable of at the resolution your
are using.
Monitor Is Stuck
In Active Off-
Mode"
The Computer Power Switch should be in the ON position.
The Computer Video Card should be snugly fitted in its slot.
Make sure the monitor's video cable is properly connected to the computer.
Inspect the monitor's video cable and make sure no pin is bent.
Make sure your computer is operational by hitting the CAPS LOCK key on the
keyboard while observing the CAPS LOCK LED. The LED should either turn
ON or OFF after hitting the CAPS LOCK key.
Missing one of
the primary
colors (RED,
GREEN, or
BLUE)
Inspect the monitor's video cable and make sure that no pin is damaged.
Make sure the monitor's video cable is properly connected to the computer.
Screen image is
not centered or
sized properly
Adjust H-Position and V-Position or press hot-key (AUTO).
Picture has color
defects (white
Adjust RGB color or select desired color temperature.

٢٠| Page
does not look
white)
Horizontal or
vertical
disturbances on
the screen
Use Windows 95/98/2000/ME/XP shut-down mode Adjust CLOCK and
FOCUS.
Press to auto-adjust.
This manual suits for next models
1
Table of contents
Other AOC Monitor manuals