Apevia PREMIER Series User manual

1
CONTENTS
1. Product Features………………………………..………………..…2
2. Product Specicaons……..………………………………………3
3. Overall Performance………………………………………………..4
4. Protecons…………………………………………………….………..4
5. Dimensions……….……………………………………………………..5
6.  Connectors………………………………………..5
RGB Fan ………………………………………..77.
Precauons………………………………………………………………7
8.
Informaon………………………………………………………………7
9.
Installaon………………………………………………….……………8
10.
11.Troubleshoong….…………………………………………..……….9

366 RGB lighting modes

3
2. Product Specifica�ons:
a. AC input voltage: 100-240V
b. AC input frequency: 60Hz/50Hz
c. Operang temperature: The power supply should be operated in an ambient
temperature of 0°C to 40°C
d. DC output:
Model
AC Input
DC Output Voltage
Max Output Current
Combined Power
Total Power
Model
850W Premier Power
AC Input
100-240V，10A / 5A，50-60Hz
DC Output Voltage
+3.3V +5V +12V -12V +5Vsb
Max Output Current
20A 20A 66A 0.3A 3A
Combined Power
100W 850W 3.6W 15W
Total Power
850W
Model 1200W Premier Power
AC Input 100-240V，15A / 7.5A，50-60Hz
DC Output Voltage +3.3V +5V +12V -12V +5Vsb
Max Output Current 20A 20A 100A 0.3A 3A
Combined Power 100W 1200W 3.6W 15W
Total Power 1200W
1000W Premier Power
100-240V，15A / 7.5A，50-60Hz
+3.3V +5V +12V -12V +5Vsb
20A 20A 83.3A 0.3A 3A
100W 1000W 3.6W 15W
1000W

4
3. Overall Performance:
a. Hold up me: 14ms at full load normal line input voltage.
b. Switching frequency: 50KHz at normal line input.
c. Stability: +/- 5% for 24KHR aer warm up.
4. Protec�ons:
a. Under voltage protecon.
If an under voltage fault occurs, the supply will latch all DC outputs into a shutdown state
when +12V,+5V +3.3V outputs under 60% of its maximum value.
b. Over voltage protecon
Output Minimum Nominal Maximum Unit
+12 VDC 13.4 15.0 17 Volts
+5 VDC 5.70 6.3 7.0 Volts
+3.3 VDC 3.70 4.2 4.8 Volts
c. Short circuit
An output short circuit is dened as any output impedance less than 0.1 ohms. The power
supply shall shut down and latch ofor shorng the +3.3 VDC,+5 VDCor+12 VDC rails.
Shorts between main output rails and +5VSB shall not cause any damage to the power
supply. The power supply shall either shut down and latch oor fold back for shorng the
negave rails.+5VSB must be capable of being shorted indenitely, but when the short is
removed, the power supply shall recover automaally or by cycling PS_ON#. The power
supply shall be capable of withstanding a connuous short-circuit to the output without
damage or overstress to the unit.

5
d. Over-power protecon
The power supply will be shut down and latch owhen output power is 110%~150%
5. Dimensions:
150mm x 158mm x 86mm (5.9" x 6.2" x 3.4") W x L x H
6. Descrip�on of Connectors:
850W / 1000W semi-modular

6
1200W full-modular

7
7.
Precau�ons:
Warning! To avoid the risk of electrical shock, unauthorized
RGB Fan Ligh�ng Func�on: 366 Selectable RGB Ligh�ng Modes
persons need the following
precauons:
a. Do not open the power supply case!
a. 
b. 

c. 


b. Avoid exposure to humidity.
8.
9 .
Informa�on:
Thank you for purchasing a high-quality Apevia product! Please visit our website at
hp://www.apevia.com for complete warranty informaon and future support for your
product. For the latest release informaon, or should you have any quesons, please visit our
website, or contact us at:
Support Phone Number: 1-909-718-0789
Support E-mail: [e-mail]

8
10. Installa�on:

9
11. Troubleshoo�ng:
If power supply fails to operate properly, please check the following before requesng for an
RMA:
a. Please make sure the power supply and power cord is connected properly.
b. Please make sure the power cord is plugged into the power socket.
c. Please make sure the power supply I/O buon is switched to the I posion.
d. Please check if all the connectors (motherboard, floppy and peripherals) are
connected properly.
e. Please allow 5 seconds interval before turning the power on again when power
supply is switched omanually (seng the I/O switch to the O posion)