Apevia Prestige Series User manual

1
CONTENTS
1. Product Features………………………………..………………..…2
2. Product Specifications……..………………………………………3
3. Overall Performance………………………………………………..4
4. Protections…………………………………………………….………..4
5. Dimensions……….……………………………………………………..5
6. Ca les & Connectors………………………………………………..5
7. Precautions………………………………………………………………7
8. Information………………………………………………………………7
9. Installation………………………………………………….……………8
10.Trou leshooting….…………………………………………..……….9

2
1. Product Features
a. Stable and reliable
b. Cosmic black casing
c. Supports single 12v output for ig er power usage
d. Supports Dual / Quad / Multi-Core CPUs
e. Ample +12 V Output, en anced +12 V current capability broadens utilization
possibilities.
f. Multi-GPU tec nologies supported, 6-Pin and 8-Pin PCI-E connectors to support all
GPU platforms
g. Built in 1 x 135mm silent automatically t ermal fan speed controlled black fan.
. Dimensions : 150mm x 86mm x 158mm (5.9" x 3.4" x 6.2") W x L x H
i. Heavy-duty protections, including OVP (Over Voltage Protection), OPP (Over Power
Protection), SCP (S ort Circuit Protection)
j. Universal AC input by active PFC (99%RF Typical)
k. DC to DC converter design, provides superior dynamic response, greater system
stability and maximizes t e 12 V DC rail output.

3
2. Product Specifications:
a. AC input voltage: 115-230V
. AC input frequency: 60Hz/50Hz
c. Operating temperature: The power supply should e operated in an am ient
temperature of 0°C to 40°C
d. DC output:
Model
600W Prestige Power
AC Input 115-230VAC , 8A/4A , 50-60HZ
DC Output Voltage +3.3V +5V +12V -12V +5Vs
Max Output Current 20A 20A 50A 0.3A 2.5A
Com ined Power 100W 600W 3.6W 12.5W
Total Power 600W
Model
800W Prestige Power
AC Input 115-230VAC , 8A/4A , 50-60HZ
DC Output Voltage +3.3V +5V +12V -12V +5Vs
Max Output Current 20A 20A 66A 0.3A 2.5A
Com ined Power 100W 792W 3.6W 12.5W
Total Power 800W
Model
1000W Prestige Power
AC Input 115-230VAC , 8A/4A , 50-60HZ
DC Output Voltage +3.3V +5V +12V -12V +5Vs
Max Output Current 20A 20A 83A 0.3A 2.5A
Com ined Power 100W 996W 3.6W 12.5W
Total Power 1000W

4
3. Overall Performance:
a. Hold up time: 14ms at full load normal line input voltage.
. Switching frequency: 50KHz at normal line input.
c. Sta ility: +/- 5% for 24KHR after warm up.
4. Protections:
a. Under voltage protection.
If an under voltage fault occurs, the supply will latch all DC outputs into a shutdown state
when +12V,+5V & +3.3V outputs under 60% of its maximum value.
. Over voltage protection
Output Minimum Nominal Maximum Unit
+12 VDC 13.4 15.0 17 Volts
+5 VDC 5.70 6.3 7.0 Volts
+3.3 VDC 3.70 4.2 4.8 Volts
c. Short circuit
An output short circuit is defined as any output impedance less than 0.1 ohms. The power
supply shall shut down and latch off for shorting the +3.3 VDC,+5 VDCor+12 VDC rails.
Shorts etween main output rails and +5VSB shall not cause any damage to the power
supply. The power supply shall either shut down and latch off or fold ack for shorting the
negative rails.+5VSB must e capa le of eing shorted indefinitely, ut when the short is
removed, the power supply shall recover automatically or y cycling PS_ON#. The power
supply shall e capa le of withstanding a continuous short-circuit to the output without
damage or overstress to the unit.

5
d. Over-power protection
The power supply will e shut down and latch off when output power is 110%~150%
5. Dimensions:
150mm x 86mm x 158mm (5.9” x 3.4” x 6.2”) W x L x H
6. Description of Connectors:

6

7
7. Precautions:
Warning! To avoid the risk of electrical shock, unauthorized persons need the following
precautions:
a. Do not open the power supply case!
. Before turning on, please make sure that the input voltage of the red RMS side switch
on the power supply corresponds to the power voltage given in your environment.
(USA & Canada: 115V; Europe, Central and South America: 230V).
c. Avoid exposure to humidity.
8. Information:
Thank you for purchasing a high-quality Apevia product! Please visit our we site at
http://www.apevia.com for complete warranty information and future support for your
product. For the latest release information, or should you have any questions, please visit our
we site, or contact us at:
Support Phone Num er: 1-909-718-0789
Support E-mail: [e-mail]

8
9. Installation:

9
10. Troubles ooting:
If power supply fails to operate properly, please check the following efore requesting for an
RMA:
a. Please make sure the power supply and power cord is connected properly.
. Please make sure the power cord is plugged into the power socket.
c. Please make sure the power supply I/O utton is switched to the “ I ” position.
d. Please check if all the connectors (mother oard, floppy and peripherals) are
connected properly.
e. Please allow 5 seconds interval efore turning the power on again when power
supply is switched off manually (setting the I/O switch to the “ O ” position)