APG IB20EJE7B User manual

IB(5”,4”)RUNNING BOARD
01-04 TOYOTA TACOMA DOUBLE CAB
Page 1of 2 12/6/16 (DP) Rev 1
PARTS LIST:
Item
QTY
Description
Item
QTY
Description
#1
2
Running Board(use for left or right)
#10
12
10mm Lock Washers
#2
2
Front Upper Mounting Brackets (DFM/PFM)
#11
12
10mm Hex Nuts
#3
2
Rear Upper Mounting Brackets (DRM/PRM)
#12
8
8-1.25mm x 25mm Hex Head Bolts
#4
2
Driver Front/Passenger Rear Mounting Brackets (DFB/PRB)
#13
16
8mm Flat Washers
#5
2
Driver Rear/Passenger Front Mounting Brackets (PFB/DRB)
#14
8
8mm Lock Washers
#6
4
10-1.5mm x 25mm Hex Bolt
#15
8
8mm Hex Nuts
#7
8
10-1.5mm x 35mm Hex Bolt
#16
24
6mm T-Bolts
#8
16
10mm Large Flat Washers
#17
24
6mm Flat Washers
#9
8
10mm Flat Washers
#18
24
6mm Lock Nuts
PROCEDURE:
1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS
CAREFULLY. ASSISTANCE IS RECOMMENDED.
2. Starting on the driver side front of the vehicle, locate the (3) mounting holes in the body support.
Partially attach a front upper Mounting Bracket to the center mounting hole in the vehicle using (1)
10mm x 25mm Hex Bolt, (2) 10mm x 20mm OD x 2mm Large Flat Washers, (1) 10mm Lock Washer
and (1) 10mm Hex Nut. Use the included (2) 8mm x 25mm Hex Head Bolts, (2) 8mm Lock Washers, (4)
8mm Flat Washers and (2) 8mm Hex Nuts in the remaining inner and outer mounting holes. Snug but
do not tighten hardware at this time.
3. Select a driver front lower bracket, attach to the front upper bracket with (2)10mmx35 Hex
bolts,(4)10mm flat washers,(2)10mm lock washers and (2)10mm Hex nuts（Figure 3）.Snug but do
not tighten hardware at this time
NOTE:THE DRIVER FRONT LOWER BRACKET AND THE PASSENGER REAR LOWER BRACKET
ARE UNIVERSAL.
4. Repeat Step 2 &3 to install the rear driver’s side Mounting Brackets.
5. Select a Running Board. Slip(12）6mm T-bolts into each bottom channel(Figure 4). Carefully position
the Running Board onto the (2) Mounting Brackets. IMPORTANT: Do not slide, (front to back), the
Running Board on the Brackets or damage to the finish may result. Attach the Running Board to the
Mounting Brackets with(6) 6mm T-bolts,(6)6mm flat washers and (6)6mm lock nuts (Figures 4). Do not
tighten at this time..
6. Level and adjust Running Board properly and tighten all hardware.
7. Repeat Steps 2-6 for installing passenger Running Board.
8. Do periodic inspections to the installation to make sure that all hardware is secure and tight.
Driver Front/
Passenger rear
Mounting
Bracket
Rear Upper
Mounting
Bracket
Front Upper
Mounting Bracket
Driver Front/
Passenger rear
Mounting
Bracket
Driver rear
/Passenger
Front Mounting
Bracket
Driver rear
/Passenger
Front Mounting
Bracket
(2) Running Board
(example only)

IB(5”,4”)RUNNING BOARD
01-04 TOYOTA TACOMA DOUBLE CAB
Page 2of 2 12/6/16 (DP) Rev 1
To protect your investment, wax this product after installing. Regular waxing is recommended to add a protective layer
over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish.
For Polished Finishes: Aluminum polish may be used to polish small scratches and scuffs on the finish. Mild soap may
be used also to clean the Running Board.
For Black Finishes: Mild soap may be used to clean the Running Board.
Driver Side Installation Pictured
(FIG 1) Driver Side Front Mounting Location
8mm x 25mm Hex Bolts
8mm Lock Washers
8mm Flat Washers
8mm Hex Nuts
(FIG 2) Driver Side Rear Mounting Location
Center bolt-use:
10mm x 25mm Hex Bolts
10mm Lock Washers
10mm Flat Washers
10mm Hex Nuts
8mm x 25mm Hex Bolts
8mm Lock Washers
8mm Flat Washers
8mm Hex Nuts
8mm x 25mm Hex Bolts
8mm Lock Washers
8mm Flat Washers
8mm Hex Nuts
Center bolt-use:
10mm x 25mm Hex Bolts
10mm Lock Washers
10mm Flat Washers
10mm Hex Nuts
Front
Rear
(Fig 4) Slip 6mm T-bolts
into the bottom channel
(Fig 5) Bracket installation
(6)6mmT-bolts
(6)6mm Flat Washers
(6)6mm Lock nuts
(2)10x35mm Hex bolt
(4)10mm Flat Washer (Large)
(2)10mm Lock Washer
(2)10mm Hex Nut
(Fig 3)Front Bracket installation pictured