apivio Liberty1 User manual

2
Basic Instructions
Basic Instructions
Please read the instructions carefully to protect yourself and others
from personal injury or damage to property.
User Precautions
· Please avoid installing in excessively hot, cold, dusty or humid
places.
· Please avoid exposure to strong vibrations or direct sunlight.
· Because the phone generates heat when it operates, please do
not install it in locations with low heat tolerance.
· To prevent re or risk of electric shock, please do not use with a
damaged cord or plug, or touch the power outlet with wet hands.
· Please do not place on an unstable surface to avoid injury or
breakage if dropped or fallen.
Precautions when installing
· Please do not touch the phone with wet hands.
· Please do not use the phone for other than its intended purpose.
· Please do not pull on the power plug and adapter when unplugging
the phone.
· If the phone emits an unusual noise or smell, or if you see smoke
coming from the phone, please unplug the adapter and cable
immediately.
· Please do not place the phone in an area that is wet or dusty.
· Please do not place anything heavy on top of the phone.
· Please do not put any foreign material inside the product or
charger.
· Please do not place the phone near or in areas of extreme heat,
such as in direct sunlight or beside a heater.
· Please do not place the product close to magnetic objects such as
a magnet, TV, monitor or speaker.
· Please back up your valuable data on the phone, as a precaution.
· Please note that the phone and battery can get heated up during a
lengthy call.
· Do not modify or disassemble the phone, or use any other
manufacturer's rmware to upgrade the phone.
· Failure to comply with the precautions in this section will void any
applicable warranty.
Precautions when using
· Please use a dry, soft cloth when you clean the phone.
· Please do not use harsh chemicals such as benzene or thinner
to clean the phone.
· Please wipe the power plug with a dry, soft cloth if it is wet or
dusty, as this may be a re or electric shock hazard.
Precautions when cleaning

3
Basic Instructions
Basic Instructions
User Precautions
Your wireless phone is a radio transmitter and receiver.
It is designed and manufactured not to exceed the emission limits
for exposure to radio frequency (RF) energy set by the Federal
Communications Commission of the U.S. Government.
These limits are part of comprehensive guidelines and establish
permitted levels of RF energy for the general population.
The guidelines are based on safety standards previously set by both
U.S. and international standards bodies:
· American National Standards Institute (ANSI) IEEE. C95.1-1992.
· National Council on Radiation Protection and Measurement
(NCRP). Report 86.1986.
· International Commission on Non-Ionizing Radiation Protection
(ICNIRP) 1996.
· Ministry of Health(Canada). Safety Code 6.
The standards include a substantial safety margin designed to
assure the safety of all persons, regardless of age and health.
The exposure standard for wireless mobile phone employs
a unit of measurement known as the Specic Absorption Rate,
or SAR. The SAR limit set by the FCC is 1.6W/kg.
FCC SAR Compliance Statement
· Please don’t use this phone with a battery from another
manufacturer, as this could damage the device.
· Replace the battery if it appears swollen, as there is a risk of
explosion.
· Use only the specied manufacturer's charger to charge the
phone.
· Keep the phone and battery away from children and pets.
· Do not place the phone or battery near rearms or unlicensed
radio products.
· Do not submerge the phone or get the battery wet.
· Do not store or use the phone inside a car during the summer,
or in steam rooms, or other areas with high temperature and
humidity.
· Do not continuously use the phone for long periods of time.
· Do not place the phone directly on blankets, electric blankets, or
carpeted areas.
· Do not allow metallic objects to come into contact with the
battery terminals.
· Do not disassemble, crush, or puncture the phone or battery, as
there is a risk of explosion and electric shock.
· Do not incinerate the battery. Dispose of it or recycle it in
accordance with local regulations.
· Normal battery life should continue for at least 6 months from
date of purchase.
· Before rst time use, and after using the phone for a long period
of time without charging, please charge the battery fully by
placing the phone in the cradle.
Precautions when using battery

4
Basic Instructions
Basic Instructions
User Precautions
· This device is for indoor use, only in the 5150~5250Mhz
frequency range.
· This device was tested for typical body-worn operations.
· To comply with RF exposure requirements, keep at least 1.5cm
(0.5 inches) between the user's body and the headset, including
the antenna.
· Do not use third-party belt clips, holsters, or other accessories
that contain metallic components.
· Avoid use of body-worn accessories that do not meet the above
criteria, as they may not comply with RF exposure requirements.
User manual specications and the IP Phone software version
may be changed by the manufacturer without any notice.
Warnings

5
Basic Instructions
Basic Instructions
Contents
Components ..................... 06
HD Voice Features ............. 06
About the Phone ............... 07
LCD Status ....................... 08
Insert the Battery ............... 09
Install the Adapter .............. 09
Wi-Fi connection ............... 10
To Access Web UI ............. 11
Basic Instructions
Useful Functions ................ 18
Text Input .......................... 20
Display .............................. 21
Setting .............................. 22
System info ....................... 23
Extra Functions
Trouble shooting ................ 24
Treatment before
Disposal ............................ 25
Warranty ............................ 25
Damage Compensation .... 26
Specifications .................... 27
Supplements
Make a Call / Hang Up ..... 14
Answering a call ................ 14
Call History ........................ 14
Transfer ............................. 15
Pick Up ............................. 15
Mute ................................. 15
Adjust Volume ................... 15
Ring Type .......................... 15
Phone Book ...................... 15
CFA ................................... 16
Message ........................... 17
Basic Functions
User Precautions ................ 02

6
Basic Instructions
Basic Instructions
6
Please check to ensure the components pictured below
are in the box after purchase. Please contact the retail
store where you purchased the device, if there are any
missing items.
Components
· This device uses high-end speakers and receivers to
support HD Voice capability.
· This device deploys HD Voice clarity similar to an HD
TV.
· This device outputs a higher voice quality than the
standard Internet phone.
HD Voice Features
<Voice quality comparison between standard
phone voice technology, and HD Voice technology>
Body Charger
Battery User manualPower adapter

7
Basic Instructions
Basic Instructions
7
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
Volume : Adjust the sound volume.
Menu : Access the phone menu.
Search : Search your registered Wi-Fi networks.
Wireless line : Search Wi-Fi networks.
Phone book : Access the phone book.
System info : Access system information.
Message : SMS(Texting is not supported at this time).
OK : Select the item.
Mute : Mute your current call.
Back : Cancel the selected item or return to the previous menu.
Call : Receive or end a call.
End : Power on/off.
Number/ Text : Input numbers or text.
#/Lock : Press and hold the [#] button to lock/unlock the keypad.
Pick up : Pick up a call from another phone on your account.
Transfer : Transfer current call to another phone number.
About the Phone

8
Basic Instructions
Basic Instructions
LCD Status
Time, Date
Indicates the time and
date.
Menu
Press to access
phone menu.
Status Icon
Indicates phone status.
Please refer to the icon
legend on the right, for
details.
Search
Press to search
phone book.
Indicates the battery is charging, and the charging status.
Indicates the phone call function is unavailable.
Indicates the phone call function is available.
Indicates the alarm has been set.
Indicates you have unread messages.
Indicates the answering machine function has been set.
Indicates that the phone is in locked mode.
Indicates Wi-Fi signal strength.
Strong signal Weak signal
Indicates battery status.
Fully charged Good Poor Charge

9
Basic Instructions
Basic Instructions
Connect the adaptor
to the rear connector.
Connect the charger plug into a power outlet.
Place the Wi-Fi phone
on the charging cradle
to charge.
Please use the included battery. If you need to
exchange or purchase another battery, please contact
an authorized service centre.
(1) Push down on the battery cover,
as shown at left, and
pull down (2) to separate.
Insert the battery with the
charging pins aligned with
the grooves (1) and push
down on (2).
Replace the battery cover
bottom first, at (1) direction
and push down, sliding up
toward (2) until you hear a
click.
Install the adaptorInsert the battery
Push
Pull
Fit up
Push
Pull
Fit up
You can check the charging status with the indicated
icon on the top display.

10
Basic Functions
Select the desired
network, Press [OK],
and enter applicable
password.
You will be connected
and can begin using
your device.
Wi-Fi Connection
Press and hold the [End]
button for 3 seconds to power
on the phone.
Press to search for
available Wi-Fi connections
While connecting to an AP, Web browser will open automatically if Web Authentication is required.
After connected to the AP, if registration to the server fails, open Web browser again and check whether it has been connected to the AP.
(Refer to the page 16)

11
Basic Functions
To Access Web UI
You can check the phone status or set up the phone via
Web browser. Please follow the steps below.
1. To check IP address
[Menu] →8.System info → 3.Network info
2. Input http://IPaddress:8000 on web browser to
access Web UI
3. Input ID:user, Password:0000 to log-in
You can check the current phone status.
Home

12
Basic Functions
To Access Web UI
Account : check the account information.
Call Setup
Phone Password : change the user password.
Network : setup roaming feature.
QoS : setup QoS related setting.
Time : select Time zone and setup NTP server.
Phone Setup

13
Basic Functions
To Access Web UI
Functions : setup the phone functions.
WiFi Scan Channel : select WiFi channels.
Function Setup
Reboot : reboot the phone.
Factory Default : restore to factory default setting.
- Please make sure before restore to factory default.
All the setting will be completed deleted.
Maintenance

14
Basic Functions
If the Out of Ofce function is activated, the phone will
answer calls with an auto-answer.
Answer a call with Out of Office function
To set the Out of Ofce function: [Menu] → 4. Useful
Functions → 1.Out of ofce
Call History
To set the answer type: [Menu] → 2.Call Manage →
2.Answer type.
Answer call directly
Answer a Call
• If Answer type is set to Press button :
Press any button to receive incoming call, except the
button.
• If Answer type is set to Hold handy :
Call is connected when you lift the phone from the
charging cradle.
To manage calls:[Menu] → 2.Call Manage → 1.Logs
You can check outgoing, incoming and missed calls.
The phone saves up to 100 logs in your history.
• Button : Call one of the logged phone numbers.
• [OK] Button : See phone number details.
• [Menu] : Send a message(if enabled) or save/delete
number.
Make a Call / Hang Up
Input the call
number
Using
phone book
Short dial
End call
Using phone
history
Press the phone
number .
In standby mode, press and hold the last digit of
Short dial. (Short dial can be registered 00~99)
Select the number
in history.
Search and select
the desired number.

15
Basic Functions
In standby mode, press [Volume] and click the
button. You can adjust Volume, Ring, Call, Power On/Off,
Alarm. Adjust the volume (8 steps) by pressing
[Volume] or .
Adjust VolumeTransfer
Adjust the volume on call : Adjust the voice volume on
a phone call(8 steps) by pressing the [Volume] button.
You can transfer a call to another number or to another
phone in the same group.
Easily search and change ringtones. Select from 10
WAV rintones or 10 MIDI ringtones.
[Menu] → 5.Sound → 1.Ring setting
Ring Type
New callOn the call Input the
number
On the call Input the
number
On the call Input the
number
You can answer another ringing phone on the same
network. This function requires a pickup code and
group.
Pick Up
Press [Mute] button during an ongoing call to mute your
voice.
Mute
Phone Book
Search Contacts
Search by assigned number, name, phone number, or
group. After selecting the item, press the [Call] button.
→ 1.Search contacts →Select →

16
Basic Functions
Phone Book
Call Forwarding
· In the phone book list, press the [Menu] button to delete
or edit entries.
Receive forwarded calls from another number.
• How to set : [Menu] → 2.Call Manage → 6.Call forwarding
→ Select the Set → → Input the number to
Call Forwarding →
• How to clear : [Menu] → 2.Call Manage → 6.Call forwarding
→ Select Unset →
· Select Call Forwarding in the Call FWD section to set the
No answer, Always, Busy options.
Follow the steps below to register new contacts.
Register Contacts
Input name Input number
Select Short dial Select Group
Select bell
· Manage groups at → 3.Manage groups.
Press the [Menu] button to Add, Edit, Delete groups and
members. Register up to 30 per Group.
· After saving and storing a number, register it as a group
member by pressing the [OK] button.
· Store up to 500 Contacts and up to 100 on speed dial.
· Press the [Search] button to locate the phone number type.

17
Basic Functions
Message setting
Send and receive messages with your phone.
Please inquire with your service provider if this function is available in your area.
Message
Write the message
Use the Search or Draft Box Save function on the Receive
Number screen.
Inbox
Spam Message
→ 1.Write → → Input the number → → Select
save mode → → Input the sender number →
→ 3.Spam Message
• Register spam number : Register up to 5 spam
numbers.
• Spam Inbox : Check the spam message.
• Setting : Choose whether to block the spam message
or not.
→ 2. Inbox
Check received, sent and draft messages.
Select a message and press the [Menu] button to
access Deliver, Save Number and Delete functions.
→ 4.Message Setting
• Arrival alarm interval : Set for once, at two minute
intervals, and to clear the alarm when message
received.
• Setting alarm bell : Select from 3 notication bell
tones.
· This function available at [Menu] → 4.Message

18
Extra Functions
Set and clear the Morning Call.
• How to set : [Menu]
→ 4.Useful Functions →
2.Morning Call → Select setting → →
Input time → → Select notice → →
Select the repeat interval and times →
→ Select bell type →
• How to clear : [Menu] → 4.Useful Functions →
2.Morning Call → Select Clear →
Useful Functions
[Menu] → 4.Useful Functions → 1.Out of Ofce
• Auto attendant : Set and clear the Out of Ofce auto
answer while away from your desk/work.
Out of Office
Press the [Menu] button to delete and add alarm.
Set and clear multiple alarm functions.
• How to set : [Menu]
→ 4.Useful Functions → 3.Alarm
→ Select setting → → Input time → →
Select notice → → Select the repeat
interval and times Select bell type →
• How to clear : [Menu] → 4. Useful Functions →
3.Alarm → Select Clear →
Alarm
Morning Call

19
Extra Functions
Useful Functions
Use the Direction buttons to cycle through, select and
display the time and date of major cities worldwide.
• How to set : [Menu] → 4.Useful Functions →
5.World time
World Time
Use the Direction buttons or [OK] button to cycle
through the on screen options. Press the [Back] button
to delete one character. Press the [Menu] button to
delete all.
• How to set : [Menu] →4.Useful Functions →4.Calculator
Calculator
To connect to an Access Point (AP) requiring Web
Authentication:In your Web browser, move the cursor
with the Navigation key. Use long key presses for faster
cursor movement.
Web Browser
1. In the Input Box, press the [Back] button to delete
all details.
2. In the Web browser, use the Volume button to toggle
Page up/Page Down and use the Pickup key and Trans
key to toggle Page Left/Page Right.
3. To change text entry mode, use key for small/
capital/numeric, and key for special character.
4. If your web browser is freezing, click button to
go back to the main page.
5. In the input box, press ‘Search’ key to use TEXT INPUT
mode.
6. TEXT INPUT key pad can be escaped once Web page
is refreshed, then press ‘Navi’ key to use TEXT INPUT
key pad again.
• How to set : [Menu] → 4.Useful Functions → 6.Web
Browser → use Navi button to go to Input Box →
→ Input ID & Password → Click Sign in button

20
Extra Functions
Text Input
- To input text, press any number or Search button then
Text input keyboard will pop up.
- Use navigation button to move, and press OK
to select the character, and press BACK button
to delete, and long Back button press to delete all.
- Press ‘Menu’ button to nish text input, and press
‘Search’ button to modify.
- Use key for small/capital character, and press
key for special character and to go back to character
entry mode press ‘a’ or ‘A’.
- Or press "*" on the handset keypad to change text
entry mode.
To use TEXT INPUT Mode
- Use keypad on the phone and press ‘Menu’ button to
complete.
- Press ‘*” on the handset keypad to change text
entry mode.
- Special character is only available on Text Input
mode.
To Use Keypad on the phone