Aqara Magic Switch S1E User manual

材质：80g金东太空梭哑粉纸
料号：D0030102-000074
工艺：风琴折
尺寸：85*60mm

Aqara Magic Switch S1E is a smart switch for wonderful
control of whole house devices. It allows for quick
replacement of traditional wall switches with a
touchscreen three-button switch. Furthermore, it
supports device or scene linkage control, enabling
seamless integration with other smart devices. The
switch is compatible with the HomeKit platform,
allowing for convenient control through the Home App.
Product Introduction
Panel
Power Supply
Touch Screen

1. The installation process of this product involves strong
electricity, and it must be operated by professionals in
accordance with electrical specifications and product
specifications product manual for installation.
2. This product is for indoor use only, please do not use it
in a humid environment or outdoors.
3. This product is only suitable for safe use in areas
below 2000 meters above sea level.
4. Pay attention to moisture, do not spill water or other
liquids on this product.
5. Do NOT place this product near a heat source.
6. Do NOT attempt to repair this product by yourself. All
repairs should be performed by an authorized
professional.
7. Do not scratch the touch screen with sharp objects.
Warnings
Notes
Use of the Works with Apple badge means that an
accessory has been designed to work specifically with
the technology identified in the badge and has been
certified by the developer to meet Apple performance
standards. Apple is not responsible for the operation of
this device or its compliance with safety and regulatory
standards. 

Apple, Apple Watch, HomeKit, HomePod, HomePod
mini, Siri, iPad, iPad Air, and iPhone are trademarks of
Apple Inc., registered in the U.S. and other countries.
1. Download the Aqara Home App
Search for "Aqara Home" in the Apple App Store, Google
Play,Xiaomi GetApps, Huawei App Gallery,or scan the
following QR code to download the Aqara HomeApp:
Use the flat screwdriver to pry open the switch panel;
Loosen the terminal screws on the back of the switch
with the screwdriver, connect the live wire to the hole L,
the neutral wire to the hole N, and connect the load
(light) wire to the L1, L2, and L3(corresponding to the le,
middle, and right buttons respectively), and tighten the
terminal screws aer confirming that the wire is correct.
The total cumulative load across all three terminals must
not exceed 2200W.
2. Installation
Before installation, please ensure that the main power
switch is turned off.
Device Binding & Initialization
1
2

Secure the switch to the wall junction box using the provided
screws, and attach the panel. Please pay attention to the
correct installation method for attaching the panel.
3
* The live wire is generally a red wire, and the neutral wire is
generally a blue or black wire
* The screw torque should not exceed 0.7N·m
L1 L2 L3
Neutral
wire
Live
wire
NL3 L2 L1L
Fastened to the junction box with screws.

Power on the device and ensure that the screen displays
normally and enters the network setup prompt page.
4
First, tilt the panel downward and
align the top portion with the
slots.
The installation is complete.
Please scan the real QR code on the screen of the device to
access the network, this picture is only for display.
Temporarilynot online
Android users only
Apple users scan the code to accessthe network >
Open Aqara Home App, scan QR code
Secondly, press the bottom part of
the panel directly to engage and
secure it in place.

* Please make sure the device is connected to a 2.4GHz Wi-Fi
network;
* The Wi-Fi name or password contains unsupported special
characters, resulting in failure to connect to the
If the device addition fails, please confirm the following:
Please select the corresponding platform to scan the code
to access the network. If you have been connected to the
network before, you need to reset the device if you switch
to another platform to connect to the network. Aer
resetting the network according to the prompts, scan the
code to access the network.
5
Please connect the mobile phone as close to the device as
possible, and make sure that the mobile phone and the
device are on the same Wi-Fi network (2.4GHz).
6
Open the Aqara Home App, click the "+" in the upper right
corner of the homepage, select "Magic Switch S1E", and
follow the instructions of the App.
7
* If you use HomeKit to add devices, you need to scan the
HomeKit QR code on the screen or manually enter the setup
code to add according to the prompts on the screen of the
App and the device.
If the adding fails, please select Retry on the device and try
adding again on the App. For assistance please check:
www.aqara.com/support.
8

If the HomeKit binding fails, please confirm the
following points:
router, please change it to regular use the character and try
again;
* The device does not support WPA/WPA2 enterprise-level
Wi-Fi networks for the moment;
* Check whether the Wi-Fi anti-scrambling setting is enabled
on the router, causing the device to fail to connect to the
Internet;
* Check whether the router has enabled AP isolation, so that
the mobile phone cannot search for the device in the LAN;
* Bridged networking is not recommended.
* Prompt "Failed to add accessories". Error messages cached
by the iOS system due to repeated failures to add the
information cannot be released, please restart the iOS
device and reset the device and try again. If it still fails,
please check the router capacitance, and try another router
and try again;
* Prompt "Accessories have been added". Please restart the
iOS device and reset the device, use manual input HomeKit
set the code mode to add again;
* Prompt "No accessory found". Please wait for 3 minutes
aer resetting the device, and then enter the HomeKit
settings manually. Add it again by setting the code.

Aer the device is successfully added, enter the system
setting page, and perform factory reset operations on
the device according to the screen information prompts.
Restoring factory settings will clear all function settings
and network data of this device.
3. Reset
Aer the device is successfully added, enter the system
setting page, and operate according to the screen
information to log out of the current account and clear
the network information, so that the device can enter
the network configuration state.
4. Reset network
* The product pictures and screen content on the above pages
are for illustration only, the actual product effect (including
but not limited to Appearance, color, size) and screen display
content (including but not limited to background, UI,
picture) may be slightly different, please refer to The real
thing shall prevail.
* In case of necessary circumstances, the above content will
be modified and adjusted without special notice.

Magic Switch S1E
Model: MS-K01D
Dimensions: 86×86×41.35mm(3.39×3.39×1.63in.)
Resolution: 480 × 480
Wireless Protocols: Wi-Fi IEEE 802.11 b/g/n 2.4 GHz
Rated Input: 220 - 240 V, 50/60 Hz, μ
Rated Load: Max 10A, Incandescent Lamp ≤ 2200W
(Three Channels in total)
Operating Temperature:-10°C ~40°C (14°F ~104°F)
Operating Humidity: 0 ~95% RH, no condensation            
What is in the Box:Aqara Magic Switch S1E× 1,User
Manual× 1,Screw Kit×2
Specifications

Aqara 妙控開關 S1E 是妙控全屋設備的智能開關，可以快速
替換墻壁開關為觸屏三鍵開關，同時支持關聯設備或場景到
該產品聯動控製；已接入HomeKit 平臺，通過家庭App可以
快速的控製該設備。
产品介绍
面板
電源
全觸摸顯示屏

使用帶有Works with Apple的徽章，意味著該配件經過專門
設計，可與徽章中所標識的技術配合使用，並且已通過開發
者認證，符合Apple性能標準，Apple不對此產品的操作或其
符合的安規標準負責。
Apple、Apple Watch、HomeKit、HomePod、HomePod
mini、Siri及iPhone商標為Apple Inc.註冊所擁有，註冊於美
國或其他國家。
1. 本產品安裝過程中涉及強電，需由專業人員依照電工規範
和產品說明書進行安裝；
2. 本產品僅限室內使用，請勿在潮濕環境或室外使用；
3. 本產品僅適用於海拔 2000 米以下地區安全使用；
4. 註意防潮，請勿將水或其他液體潑灑到本產品上；
5. 請勿將本產品置放於靠近熱源的地方；
6. 請勿嘗試自行維修本產品，應由授權的專業人士進行此項
工作。
7. 請勿使用尖銳物品刮劃觸摸屏。
安全咨詢及註意事項
用戶須知

1.下載客戶端
2.安裝方式
快速設置
在應用商店搜索「Aqara Home」或掃描以下二維碼下載「
Aqara Home」 App。
安裝前請確認電源總閘已關閉！
使用一字螺絲刀撬開開關面板；
*火線一般為紅色導線，零線一般為藍色或黑色導線。
1
使用螺絲刀擰松開關背面接線柱螺絲，將火線接入L孔，將零
線接入N孔，將負載（燈）線接入L1、L2、L3孔（分別對應左、中、
右鍵），確認接線正確後，擰緊接線柱螺絲，三路累計負載不能
超過2200W；
2
使用附送的螺絲將開關固定到墻壁接線盒上，並扣上面板，
請務必註意面板的扣接安裝方式。
3
L1 L2 L3 零線火線
NL3 L2 L1L

*螺絲扭矩請勿超過0.7N·m。 使用螺絲固定到接線盒上。
安裝完成。首先，面板傾斜向下，頂部扣上卡槽，
其次，面板下部直接下壓扣合。
給設備上電，等設備屏幕正常顯示且進入入網提示頁面。
4

暫不入網
打開 掃碼入網
僅限安卓用戶
蘋果用戶掃碼入網
*請掃描設備屏幕真實二維碼入網，該圖僅做展示
請選擇對應的平臺進行掃碼入網。若之前已入過網，切換為另
一個平臺入網需重置設備。可按照提示重置網絡後，掃碼入網。
5
請將手機盡量靠近設備進行連接，同時請確保手機與設備處於
同一Wi-Fi網絡（2.4GHz）。
6
打開Aqara Home App，點擊首頁右上角「+」，選擇「妙控開關
S1E「，並且依照App指示進行操作。
7
如添加失敗，請在面板上選擇重試，在App上重試添加。如需幫
助請查詢: www.aqara.com/support。
8
*若使用HomeKit添加設備，根據App和設備屏幕上的提示需要掃
描屏幕上的HomeKit 二維碼或者手動輸入設置代碼進行添加。
*請確保設備連接2.4GHz的Wi-Fi網絡;
*Wi-Fi名稱或密碼包含不支持的特殊字符，導致無法連接路由器，請
修改成常用的字符後再試；
*設備暫時不支持WPA/WPA2企業級的Wi-Fi網絡;

3.恢復出廠設置
4.重置網絡
如果設備添加失敗，請確認以下幾點:
*檢查路由器是否開啟Wi-Fi防蹭設置，導致設備無法正常聯網;
*檢查路由器是否開啟AP隔離，導致手機在局域網內無法搜索到設備;
*建議不要連接橋接網絡。
*提示「無法添加配件」。由於反復多次添加失敗，導致iOS系統緩存
的錯誤信息無法釋放，請重啟iOS設備並重置設備後再試。若仍失
敗，請檢查路由器兼容性，並嘗試更換其他路由器再試。
*提示「配件已添加」。請重啟iOS設備並重置設備後，采用手動輸入
HomeKit設置代碼方式重新添加。
*提示「未找到配件」。請重置設備後，等待3分鐘後，采用手動輸入
HomeKit設置代碼方式重新添加。
*如遇必要情形，而對上述內容進行修改和調整，恕不專門通知。
*以上頁面中的產品圖片及屏幕內容僅作示意，實物產品效果（包
括但不限於外觀、顏色、尺寸）和屏幕顯示內容（包括但不限於背
景、UI、配圖）可能略有差異，請以實物為準。
面板添加成功後，進入系統設置頁面，根據面板上信息提示操作，
對設備進行恢復出廠操作。恢復出廠設置將清除本設備所有的功
能設置和網絡數據。
面板添加成功後，進入系統設置頁面，根據面板上信息提示操作，
則可退出當前帳號，並清除網絡信息，使設備進入可配網狀態。
面板添加成功後，進入系統設置頁面，根據面板上信息提示操作，
則可退出當前帳號，並清除網絡信息，使設備進入可配網狀態。

基本參數
妙控開關 S1E
產品型號: MS-K01D
產品尺寸: 86 × 86 × 41.35 mm (3.39 × 3.39 × 1.63 in.)
屏幕分辨率: 480 × 480
無線連接: Wi-Fi IEEE 802.11 b/g/n 2.4 GHz
額定參數: 220 - 240 V, 50/60 Hz, μ
額定負載： Max 10A, 白熾燈 ≤ 2200W (共三路)
工作溫度: -10°C ~ 40°C (14°F ~ 104°F)
工作濕度: 0 ~ 95% RH, 無冷凝
包裝清單: 妙控開關×1，使用說明書×1，螺絲×2

製造商：深圳綠米聯創科技有限公司
住所：中国・深圳市南山区桃源街道福光社区留仙大道3370号南山
智园崇文园区1棟801-804室
網站支援：www.aqara.com/support
售後電子信箱：[email protected]
Manufacturer:LumiUnited Technology Co., Ltd.
Address:Room 801-804, Building 1, Chongwen Park, Nanshan
iPark, No. 3370, Liuxian Avenue, Fuguang Community, Taoyuan
Residential District, Nanshan District, Shenzhen, China.
Online Customer Service:www.aqara.com/support
Email:[email protected]om