Aqua One Regency 100 User manual

Base x 1
I
Regency 100
Assembly instructions
Ex2 Fx16
J
Centre Panel
x 1
Left door x 1 Right door x 1
P Q
Ax16 Bx16 Cx8 Dx2
Hx4
Tools required:
Zx8
Left side x 1 Right side x 1
M N
K Lower back
panel x 1
L Top back
panel x 1
R
Shelves
x 2
Top of Cabinet
O
Glass Aquarium x 1
U
X
Hood Insert x 1
Contents:
Parts Required
Hood x 1
W
Glass tray x 1
V
Glass Lids x 2
Step 6: Hood W, aquarium U and cabinet
Place aquarium Uon top of
cupboard by lifting it on from
the back and sliding it forward.
VERY IMPORTANT: DO NOT REMOVE THE
POLYSTYRENE ATTACHED TO THE BOTTOM
OF THE AQUARIUM!
Install Filter (see filter instructions for details)
Install Heater (see heater instructions for details)
Put glass tray Von top of aquarium.
Install reflector lighting (see lighting instructions
for details)
Slide hood Wonto aquarium. Insert maintenance
lid Xinto the hood.
U
cover
hood
W
®
Aqua One and Kong’s are registered trademarks. www.aquaone.com.au.
©
Aqua One 2004
Precision Manufactured in the P.R.C.
Designed in Australia by Aqua One
Distributed in Australia by:
Kong's (Aust.) Pty. Limited
48 Williamson Rd. Ingleburn.
2565 NSW Australia.
Distributed in New Zealand by:
Kong's (NZ) Limited
52 Glenlyon Avenue.
Greerton. Tauranga New Zealand.
Distributed in the UK by:
Kong’s (UK) Ltd.
C/O Aqua Pacific UK Ltd.
PO Box 268
Romsey Hampshire
S051 0WW
United Kingdom
Important Notice
It is absolutely imperative that you ensure this cabinet and aquarium is installed upon level flooring. It is also a prerequisite that
you ensure the flooring upon which it is positioned is able to support the weight of this aquarium which could be up to 600kg
including water and decorations.
Installation upon uneven flooring will result in poor distribution of weight. Damages to the aquarium, cabinet or equipment and
damages caused by leaks due to improper or uneven installation are not covered by the guarantee with this product.
Care and Maintenance of your Aqua One Aquarium
Glass: It is recommended that you use a good quality glass cleaner and a non abrasive lint free cloth. Glass cleaner should only
be used on the outside of the aquarium.
To clean the glass on the inside of the aquarium, it is recommended that you use an Aqua One Scraper or Magnetic Cleaner
(available from your local Aqua One dealer).
Cabinet and Hood: The use of a damp cloth is recommended, do not use any detergents or harsh chemicals to clean the cabinet
and hood as damage may occur.
light
glass tray
heater
canister
filter
X
V
Instruction version:- 22/02/2008

J
O
R
Step 4: Cabinet lid O and 8 x C
Position cabinet lid on the cabinet
construction, open side pointing
upwards. Line up screws C with
holes and fasten, ensuring screw
heads do not stand proud.
Step 5: Door panels P, Q, 4 x H, 16 x F
Fasten hinges H to door
panels using screws F
P Q
H H
E
Attach door handles
Attach doors to cabinet
using screws F and
the predrilled holes
Insert shelves using
pins Z
M
O
Step 3: Side Panels M, N, 12 x A
M
M N
A
DD
J
K
I
B
A
I
B B
L
K
B
Step 1: Prepare Base I,
cantre panel J and back
panels L & K
Make sure arrow points
towards opening for screw
Step 2: Install back panels Step 3: Install centre panels
B
J
Lower back panel onto screws and tighten clamps by turining
them clockwise. Tip: Depending upon your preference you can
reverse the back panels so that the screw heads show on the back of the cabinet, rather than the inside.
J