Aqua PRO 63013 User manual

OWNER’S MANUAL
CONVERTIBLE JET PUMP
Questions, problems, missing parts? Before returning to the store call AQUAPRO
Customer Service 8 a.m. - 6 p.m., EST, Monday-Friday
1-844-242-2475
© 2017 Copyright GP Enterprises Co., Ltd.
Rev.07/03/17
Model 63013/63023/63033

2 For Professional Technical Support call 1-844-242-2475
PERFORMANCE
Model
HP
GPM of Water @ Total Discharge Pressure of 40 psi
Max. Pressure
shutoff
5 ft.
10
ft.
20
ft.
30
ft.
40
ft.
50
ft.
60
ft.
70
ft.
80
ft.
90
ft.
100
ft.
110
ft.
63013
1/2
7.5
6.6
5.5
5.0
4.7
3.8
3.5
2.2
-
-
-
-
66PSI
63023
3/4
9.0
8.1
6.2
6.0
5.3
4.5
3.5
3.0
2
1.5
-
-
67PSI
63033
1
13.5
11.6
9.0
7.4
7.0
6.0
5.1
4.6
3.2
2
1.5
1
67PSI
SAFETY INSTRUCTIONS
1. Do not pump flammable or explosive liquids such as oil, gasoline, kerosene, ethanol, etc. Do not use in the presence of
flammable or explosive vapors. Using this pump with or near flammable liquids can cause an explosion or fire, resulting
in property damage, serious personal injury, and/or death.
2. ALWAYS disconnect the power to the pump before servicing.
3. Do not touch the motor housing during operation. The motor is designed to operate at high temperatures. Do not
disassemble the motor housing.
4. Do not handle the pump or pump motor with wet hands or when standing on a wet or damp surface, or in water.
5. Wear safety goggles at all times when working with pumps.
6. This is a dual voltage 115/230 V pump. VOLTAGE SELECTOR INSIDE PRESET TO 230V.For 115V selection, please
open the terminal cover and set the switch to the proper voltage. All wiring should be performed by a qualified
electrician.
7. Protect the electrical cord from sharp objects, hot surfaces, oil, and chemicals. Avoid kinking the cord. Do not use
damaged or worn cords.
8. Ensure the electrical power source is adequate for the requirements of the pump.
9. Failure to comply with the instruction and designed operation of this unit may void the warranty. ATTEMPTING TO USE
A DAMAGED PUMP can result in property damage, serious personal injury, and/or death.
10. The pump should be connected to a 230V/115V GFCI outlet protected with a 10 amp(230V)/20 amp(115V) fuse or
circuit breaker.
11. Know the pump and its applications, limitations, and potential hazards.
12. Secure the pump to a solid base.
13. Periodically inspect the pump and system components. Disconnect the pump from the power supply before inspecting.
14. Follow all local electrical and safety codes, along with the National Electrical Code (NEC). In addition, all Occupational
Safety and Health Administration (OSHA) guidelines must be followed.
15. The motor of this pump has a thermal protector that will trip if the motor becomes too hot. The protector will reset itself
once the motor cools down and an acceptable temperature has been reached. The pump may start unexpectedly if it is
plugged in.
16. This pump is made of high-strength, corrosion-resistant materials. It will provide trouble-free service for a long time
when properly installed, maintained, and used. However, inadequate electrical power to the pump, dirt, or debris may
cause the pump to fail. Please carefully read the manual and follow the instructions regarding common pump problems
and remedies.

For Professional Technical Support call 1-844-242-2475 3
PRE-INSTALLATION
APPLICATION
This unit is a convertible jet pump designed for pumping water where the water level is less than 70 ft. deep. If the water level
to the pump is deeper than 70 ft., a deep well submersible pump should be selected. Apressure switch pre-set at 30 psi “on”/
50 psi “off” has been installed on the pump. The pressure switch will automatically turn the pump on and off based on the
system pressure.
TOOLS REQUIRED
SPECIFICATIONS
POWER SUPPLY
115V/230V, 60 HZ., 20/10 Amp Circuit
LIQUID TEMP. RANGE
32°F to 77°F (0°- 25°C)
DISCHARGE SIZE
1 in. FNPT
SUCTION SIZE
1-1/4 in. FNPT
SHALLOW WELL WATER LEVEL
25 ft.
DEEP WELL WATER LEVEL
70 ft.
DETERMINE THE DEPTH OF YOUR WELL
Tie a small but heavy weight such as a fishing weight to the end of a piece of cotton string. Lower the weight into the well until
it reaches the bottom of the well. Make a mark on the string at ground level. Pull the weight out of the well and measure from
the bottom of the weight to the ground level mark. This is the depth of your well. Subtract 5 ft. from the depth of your well. If
this number is less than 25 ft., shallow well installation should be taken. If this number is more than 25 ft. and less than 70 ft.,
deep well installation should be taken. If this number is more than 70 ft., a deep well submersible pump should be selected.
Measure the ground level mark to the mark where the cotton string is wetted. This number is your well’s water level. It should
also be at least 10 ft. below the well’s water level while the pump is running in order to prevent the pump from sucking air due
to water level drawdown.
Phillips
Screwdriver
Flathead
Screwdriver
Thread Tape
Tape Measure
Safety goggles
Pipe wrench
Hacksaw
PVC glue

4 For Professional Technical Support call 1-844-242-2475
LOCATION OF THE PUMP
Decide on the area for the pump installation. Select a pump location with adequate space for future pump maintenance. It
can be located in the basement or utility room of the house, at the well, or between the house and the well. If installed outside
of the house, it should be protected by a pump house with auxiliary heat to prevent possible freezing. Protect the pump
against flooding and excess moisture. The well also should be protected for sanitary reasons. Mount the pump as close to
the well as possible.
TANKS - PRE-CHARGED STORAGE
For best performance of the pump, it is recommended that you use a diaphragm pressure tank (sold separately). It is best to
have this in place before installing the pump. Apre-charged storage tank has a flexible bladder or diaphragm that acts as a
barrier between the compressed air and water. This barrier prevents the air from being absorbed into the water and allows
the water to be acted on by compressed air at initially higher than atmospheric pressures (pre-charged). More usable water
is provided than with a conventional type tank.
CAUTION: In order for the pump and tank to operate properly, the pressure tank needs to be drained of all water BEFORE
INSTALLING THE NEW PUMP. After draining, if you are using the supplied 30/50 psi pressure switch at the pre-set settings,
add or adjust the air pressure in the tank to 28 psi of pressure BEFORE start up.
For wells 25 ft. or less in depth, shallow well installations should be adapted. The shallow well installations have only one
single pipe between the pump and well water.
WARNING:ELECTRICAL SAFETYCapacitor voltage may be hazardous. To discharge the motor capacitor, hold the
insulated handle screwdriver BY THE HANDLE and short capacitor terminals together. Do not touch the metal screwdriver
blade or capacitor terminals. If in doubt, consult a qualified electrician.
CAUTION:Do not touch an operating motor. Modern motors are designed to operate at high temperatures. To avoid
burns when servicing the pump, allow it to cool for 20 minutes after shut-down before handling.
Do not allow pump or any system component to freeze.
To do so will void warranty.
Pump water only with this pump.
Periodically inspect the pump and system components.
Wear safety glasses at all times when working on pumps.
Keep the work area clean, uncluttered and properly lighted; store properly all unused tools and equipment.
Keep visitors at a safe distance from the work areas.
WARNING:The pump body may explode if used as a booster pump unless a relief valve capable of passing full pump flow at
75 psi is installed.

For Professional Technical Support call 1-844-242-2475 5
SHALLOW WELL INSTALLATION
MATERIALS REQUIRED (NOT INCLUDED)
One can PVC cement & primer (read instructions carefully)
One well seal with vent plug
One can thread compound (read instructions carefully)
Foot valve
Teflon tape
Discharge tee/Priming tee and plug
Rigid pipe
Relief valve
Check valve
Adaptor
Flexible plastic pipe/clamps
Tank
Tank tee
WARNING: All joints and connections must be AIRTIGHT. A single leak will prevent the proper operation of the pump. Wrap
thread tape clockwise on all threaded connections. For all non-threaded connections, you must use PVC Purple Primer and
PVC Cement to ensure airtight seals. Measure all pipe lengths before attaching.
NOTE: A foot valve is a check valve that is used to keep the water from running back into the well from the pump and
maintain hydraulic pressure when the pump is not running. If the foot valve does not hold the water the pump will lose it's
prime and will not pump water. If the foot valve open pressure is too high (the spring is too stiff), or the flow area is too small,
the pump suction head and flow rate will significantly drop.
NOTE: The suction pipe size should not be less than 1-1/4 in. The suction size of this pump is 1-1/4 in. FNPT.
CAUTION: To avoid skin burns, unplug the pump and allow time for it to cool after periods of extended use.
REPLACING AN EXISTING PUMP
Warning: Risk of electric shock. Can shock, burn or kill.
Disconnectpower to pump before working on pump or motor.
1. Drain and remove the old pump. Check the old pipe for scale,
lime,rust, etc., and replace it if necessary.
2. Install the pressure gauge in the pump body.
3. Install the pump in the system. Make sure that all pipe joints in
thesuction pipe are air-tight as well as water tight. If the suction pipe
cansuck air, the pump will not be able to pull water from the well.
4. Adjust the pump mounting height so that the plumbing connections
donot put a strain on the pump body. Support the pipe so that the
pumpbody does not take the weight of piping or fittings.
You have just completed the well plumbing for your new shallow well
jetpump. Please go todischarge pipe and tank connections.

6 For Professional Technical Support call 1-844-242-2475
NEW SHALLOW WELL INSTALLATION
Well Point Installation
1. Install pressure gauge in the pump body.
2. Drive the well, using “drive couplings”and a “drive cap”.
“Drive fittings”are threaded all the way through and allow the
pipe ends to butt against each other so that the driving force of
the manual is carried by the pipe and not by the threads. The
ordinary fittings found inhardware stores are not threaded all
the way through the fitting and cancollapse under impact.
“Drive fittings”are also smoother than standardplumbing
fittings, making ground penetration easier.
3. Mount the pump as close to the well as possible.
4. Use the fewest possible fittings (especially elbows) when
connectingthe pipe from the well point to the pump suction port.
The suction pipeshould be at least as large as the suction port
on the pump (include acheck valve). Support the pipe so that
there are no dipsor sags in the pipe, so it doesn’t strain the pump body, and so thatit slopes slightly upward from the well to
the pump (high spots cancause air pockets which can air lock the pump). Seal the suction pipejoints with PTFE pipe thread
sealant tape or a PTFE-based pipe jointcompound approved for use on PVC. Joints must be air- and watertight.
If the suction pipe can suck air, the pump cannot pull water fromthe well. If one well point does not supply enough water,
considerconnecting two or three well points to one suction pipe.
You have just completed the suction piping for your new shallow well jetpump. Please go to discharge pipe and tank
connections.
Cased Well Installation, 2”or Larger Casing
1. Install the pressure gauge in the pump body.
2. Mount the pump as close to the well as possible.
3. Assemble the foot valve, strainer, and well pipe. Make sure that
the foot valve works freely.
4. Lower the pipe into the well until the strainer is five feet above
the bottom of the well. It should also be at least 10 feet below the
well’s water level while the pump is running in order to prevent the
pump from sucking air. Install a sanitary well seal.
5. Install a priming tee, priming plug, and suction pipe to the drop
pipe.
If the distance from the well to the pump is substantial, add a
priming tee at the pump. Connect the pipe from the well to the
pump suction port, using the fewest possible fittings –especially
elbows –as fittings increase friction in the pipe. The suction pipe
should be at least as large as the suction port on the pump.
Support the pipe so that there are no dips or sags in the pipe, so it doesn’t strain the pump body, and so that it slopes slightly
upward from the well to the pump (high spots cancause air pockets which can air lock the pump). Seal the suction pipe joints
with PTFE pipe thread sealant tape or a PTFE-based pipe joint compound. Joints must be air- and water-tight. If the suction

For Professional Technical Support call 1-844-242-2475 7
pipe can suck air, the pump cannot pull water from the well.
You have just completed the suction piping for your new shallow well jet pump. Please go discharge pipe and tank
connections.
Installation for Surface Water
Caution: Possible contamination. Do not use surface water for drinking.
1. Install the pressure gauge in the pump body.
2. The pump should be installed as close to the water as possible, with the fewest possible fittings (especially elbows) in the
suction pipe. The suction pipe should be at least as large as the suction
port on the pump.
3. Assemble a foot valve and suction pipe. Make sure that the foot valve
works freely. Use PTFE pipe thread sealant tape or a PTFE-based pipe
joint compound on threaded pipe joints. Protect the foot valve assembly
from fish, trash, etc, by installing a screen around it.
4. Lower the pipe into the water until the strainer is five feet above the
bottom. It should also be at least 10 feet below the water level in order to
prevent the pump from sucking air.
5. Install a priming tee, priming plug, and suction pipe to the pump.
Support the pipe so that there are no dips or sags in the pipe, so it
doesn’t strain the pump body, and so that it slopes slightly upward from
the well to the pump (high spots can cause air pockets which can air lock
the pump). Seal the suction pipe joints with PTFE pipe thread sealant tape or a PTFE-based pipe joint compound. Joints
must be air and water-tight. If the suction pipe can suck air, the pump cannot pull water from the well.
You have just completed the plumbing for your new shallow well jet pump. Please go to discharge pipe and tank
connections.
Discharge Pipe and Pressure Tank Connections
Standard Tank Connection
1. Install a close nipple and a tee in the pump discharge port. Mount
arelief valve in one arm of the tee.
2. Install a second close nipple and tee in the open arm of the first tee.
Puta priming plug in one arm of the second tee.
3. Run a pipe from the open arm of the second tee to the inlet port of
yourtank. The pipe size must be at least as large as the pump discharge
port.
4. Remove the 1/8”NPT pipe plug from the pump Air Volume
Control(AVC) port. Run tubing from the pump’s AVC port to the port on
theAVC mounted on the tank. See instructions provided with tank and
AVCfor details.
You have just completed the tank connection for your jet pump. Please
goto electrical hookup.

8 For Professional Technical Support call 1-844-242-2475
Priming
CAUTION: Risk of burns. Never run pump dry. Running pump without water
may cause pump to overheat, damaging seal and possibly causing burns to
persons handling pump. Fill pump with water before starting.
WARNING: Risk of explosion and scalding. Never run pump against
closed discharge. To do so can boil water inside pump, causing hazardous
pressure in unit, risk of explosion and possibly scalding persons handling
pump.
1. Fill the pump through the pump outlet, fill all piping between the pump and
the well, and make sure that all piping in the well is full. If you have also
installed a priming tee in the suction piping, remove the plug from the tee and
fill the suction piping.
2. Replace all fill plugs.
Electrical
WARNING: It is recommended all electrical work be performed by a licensed electrician.
WARNING: Before wiring the pressure switch, turn off the power source to which you are connecting to avoid potentially life
threatening electrical shock.
WARNING: When wiring from the power source to the pressure switch, it
is recommended that you use either a 14-gauge or 12-gauge cord.To
complete the installation, you must connect the power source to the
pressure switch. A 30/50 psi pressure switch has been installed on the
pump. The pressure switch allows for automatic operation; the pump
starts when pressure drops to the “cut-in” setting (30 psi pre-set).
To wire the pressure switch:
Remove the pressure switch cover on the pump to expose the wiring
terminals.
Connect the green ground wire of the power supply to the switch ground terminal.
Connect the power supply wires to the two outside terminals marked “LINE” and replace the switch cover.
CAUTION:Do NOT use a pressure switch set at a pressure greater than 50 psi. The pump will not create pressures
greater than 50 psi, if so the pump will never shut off, resulting in damage to the pump and voiding the warranty.
Voltage Setting
This pump is pre-wired at 230 volts.
If the power source is 115 volts, remove the electrical housing
cover.
Flip the switch to 115 volts. Replace the cover.
NOTE: All electrical work should be performed by a licensed
electrician.

For Professional Technical Support call 1-844-242-2475 9
Start the Pump
1. Power on! Start the pump. The pump should pump water in two or three minutes.
2. If you don’t have water after 2 or 3 minutes, stop the pump and remove the fill plugs. Refill the pump and piping. You may
have to repeat this two or three times in order to get all the trapped air out of the piping.
The control valve remains open throughout this procedure.
3. After the pump has built up pressure in the system and shut off, check the pressure switch operation by opening a faucet
or two and running enough water out to bleed off pressure until the pump starts. The pump should start when pressure drops
to 30 PSI and stop when pressure reaches 50 PSI. Run the pump through one or two complete cycles to verify correct
operation. This will also help clean the system of dirt and scale dislodged during installation.
Congratulations on a successful installation.
If you were unsuccessful, please refer to Troubleshooting or call ourcustomer service technical staff.
DEEP WELL INSTALLATION
MATERIALS REQUIRED (NOT INCLUDED)
One can PVC cement & primer (read instructions
carefully)
One well seal with vent plug
One can thread compound (read instructions
carefully)
Foot valve
Teflon tape
Discharge tee/Priming tee and plug
Rigid pipe
Relief valve
Check valve
Adaptor
Flexible plastic pipe/clamps
Tank
Elbow
Tank tee
Nipple
WARNING: All joints and connections must be AIRTIGHT. A single leak will prevent the proper operation of the pump. Wrap
thread tape clockwise on all threaded connections. For all non-threaded connections, you must use PVC Purple Primer and
PVC Cement to ensure airtight seals. Measure all pipe lengths before attaching.
NOTE: A foot valve is a check valve that is used to keep the water from running back into the well from the pump and
maintain hydraulic pressure when the pump is not running. If the foot valve does not hold the water the pump will lose it's
prime and will not pump water. If the foot valve open pressure is too high (the spring is too stiff), or the flow area is too small,
the pump suction head and flow rate will significantly drop.
CAUTION: To avoid skin burns, unplug the pump and allow time for it to cool after periods of extended use.
REPLACING AN EXISTING PUMP
Warning:Risk of electric shock. Can shock, burn or kill. Disconnect power to pump before working on pump or motor.
1. Drain and remove the old pump and the ejector in the well. Check pipe for scale, lime, rust, etc., and replace it if
necessary.
NOTICE: Your old ejector (in the well) can’t be properly matched to your new pump. You must use the included ejector
to your new pump.
2. Refer the followinginstruction to finish the new pump installation.

10 For Professional Technical Support call 1-844-242-2475
NEW DEEP WELL INSTALLATION
4”Or Larger Well
1. Removing the pre-assembled ejector first then removing the pre-assembled nozzle and venturi.
2. Attaching the nozzle and venturi to the ejector
63013
Wrap the threads of the venturi tube (J32P-18/#11) and the nozzle (#01/52)with thread tape.
Use the 5/8 inch socket to thread the nozzle (#01/52) in the ejector, thread the venturi tube (J32P-18/#11) in
the ejector.
63023/63033
Wrap the threads of the venturi tube (J32P-18/#11) with thread tape.
Attach the O-ring on the nozzle (#02) and screw the nozzle (#02) into the venturi tube (J32P-18/#11).
Attach the venturi tube (J32P-18/#11) with the nozzle and O-ring to the Ejector.

For Professional Technical Support call 1-844-242-2475 11
3. Mount the pump as close to the well as possible.
4. Connect two pipes (1”drive, 1-1/4”suction) to the ejector and lowerthe ejector into the well until it is five feet from the
bottom. It shouldalso be at least 10 feet below the well’s water level while the pump isrunning in order to prevent the pump
from sucking air.
5. Install a sanitary well seal and connect the ejector piping to the pump.Use steel nipples through the well seal with flexible
poly pipe to avoidcrushing the plastic pipe when tightening the seal.
6. Support the pipe so that there are no dips or sags in the pipe, so itdoesn’t strain the pump body, and so that it slopes
slightly upwardfrom the well to the pump (high spots can cause air pockets which canair lock the pump). Seal the suction
pipe joints with PTFE pipe threadsealant tape or a PTFE-based pipe joint compound. Joints must be airandwater-tight. If the
suction pipe can suck air, the pump cannot pullwater from the well.
You have just completed the plumbing for your new double pipe deep welljet pump. Please go to priming.
Priming
Caution: Risk of burns. Never run pump dry. Running pump withoutwater may cause pump to overheat, damaging seal
and possibly causingburns to persons handling pump. Fill pump with water before starting.
Warning: Risk of explosion and scalding. Never run pump against closeddischarge. To do so can boil water inside pump,
causing hazardous pressurein unit, risk of explosion and possibly scalding persons handling pump.
1. Pull out the pressure tube from the 90°elbow insert. Unthread and remove the elbow insert from the pump body.

12 For Professional Technical Support call 1-844-242-2475
2. Wrap the threads of the 1/4 in. pressure gauge(included) or plug with thread tape and thread it in the elbow insert
hole.Cut off the expanded portion of the pressure tube.
3. Fill the pump through the pump outlet, fill all piping between the pump and the well, and make sure that all piping in the
well is full. If you have also installed a priming tee in the suction piping, remove the plug from the tee and fill the suction
piping.Replace all fill plugs.
4. Install the pressure regulator(included)into the top of the pumpand close the pressure regulator completely
NOTE: This pressure regulator is a normally-closed valve installed at the discharge of the pump to provide an obstruction to
flow and thereby regulate the pump pressure and provide back pressure for the ejector. Failure to use this item may result in
a loss of prime and/or a low pressure.

For Professional Technical Support call 1-844-242-2475 13
5. Thread the 1/4 in. elbow insert into the 1/4 in. hole on the side of the pressure regulator. Slide the pressure tubing
(attached with the pump pressure switch or included in regulator kit) over the 1/4 in. brass elbow and the pressure switch
connector.
6. Wrap thread tape around the threads of a 3/4 in. MNPT x 1 in. slip PVC adaptor (sold separately), and thread the
adaptor in the pressure regulator.
Discharge Pipe and Pressure Tank Connections
Wrap all threads with thread tape.
In order for the pump and the pressure tank (sold separately) to operate properly,
the pressure tank needs to be drained of all water BEFORE INSTALLING IT TO
THE PUMP.
Thread a 10 in. tank tee (sold separately) or another necessary size tee into the
pressure tank.
Plug one outlet on top of the tank tee with a 1/4 in. plug (sold separately) and
install a pressure gauge (sold separately) on the other outlet on top of the tank
tee.
Thread two 1 in. female PVC adaptors (sold separately) onto the two inlet sides of tank tee.
Thread a 1/2 in. relief valve and a 1/2 in. drain valve (both sold separately) to the front of the tank tee.
Using PVC purple primer and PVC cement, attach a section of 1 in. PVC pipe (sold separately) as needed to connect the
3/4 in. MNPT x 1 in. slip PVC adaptor in the pressure regulator.
Attach another section of 1 in. PVC pipe (soldseparately) as needed to connect the other 1 in. female PVC adaptor on the
tank tee to the water system from the house.

14 For Professional Technical Support call 1-844-242-2475
Electrical
WARNING: It is recommended all electrical work be performed by a licensed electrician.
WARNING: Before wiring the pressure switch, turn off the power source to which you are connecting to avoid potentially life
threatening electrical shock.
WARNING: When wiring from the power source to the pressure switch, it is recommended that you use either a 14-gauge or
12-gauge cord.To complete the installation, you must connect the power source to the pressure switch. A30/50 psi pressure
switch has been installed on the pump. The pressure switch allows for automatic operation; the pump starts when pressure
drops to the “cut-in” setting (30 psi pre-set).
To wire the pressure switch:
Remove the pressure switch cover on the pump to expose the wiring terminals.
Connect the green ground wire of the power supply to the switch ground terminal.
Connect the power supply wires to the two outside terminals marked “LINE” and replace the switch cover.
CAUTION: Do NOT use a pressure switch set at a pressure greater than 50 psi. The pump will not create pressures
greater than 50 psi, if so the pump will never shut off, resulting in damage to the pump and voiding the warranty.
Voltage Setting
This pump is pre-wired at 230 volts.
If the power source is 115 volts, remove the electrical
housing cover.
Flip the switch to 115 volts. Replace the cover.
NOTE: All electrical work should be performed by a licensed
electrician.

For Professional Technical Support call 1-844-242-2475 15
Start the Pump
Note: Before start the pump, close the pressure regulator completely
1. Power on! Start the pump and watch the pressure gauge. The pressureshould build
rapidly to 50 PSI as the pump primes.
2. After 2 or 3 minutes, the gauge should showpressure. If not, stop the pump, remove
the fill plugs, reopen the controlvalve, and refill the pump and piping. You may have to
repeat this twoor three times in order to get all the trapped air out of the piping.
Don’tforget to close the control valve each time before you start the pump.
3. When water pressure has built up and is maintained by the pump,slowly open the
pressure regulator while watching the pressure gaugeneedle. Slowly unscrew the
adjusting screw until maximum water flow is obtained without dropping to zero.
If pressure falls completely, retighten the screw and readjust. If no pressure shows,
stop the pump, remove the pressure regulator from pump, add more water, and try
again.
4.After the pump has built up pressure in thesystem and shut off, check the pressure
switch operation by opening afaucet or two and running enough water out to bleed off
pressure untilthe pump starts. The pump should start when pressure drops to 30
PSIand stop when pressure reaches 50 PSI. Run the pump through oneor two
complete cycles to verify correct operation. This will also helpclean the system of dirt
and scale dislodged during installation.
TROUBLESHOOTING
WARNING: Disconnect power and release all pressure from the system before attempting to install, service, relocate or
perform any maintenance.
DRAINING THE PUMP
Drain openings are provided on all models. To drain the
pump:
Unplug the pump from power supply outlet.
Remove drain plug close to the inlet hole and air plug
located on the top of the pump close to the outlet hole,
to vent the piping system.
Drain all piping to a point below the freeze line. This will
drain the pump.
NOTE: While this will drain the pump, it will not necessarily drain all the unprotected parts of the piping system. To drain tank,
disconnect the piping at the tank outlet.

16 For Professional Technical Support call 1-844-242-2475
Problem
Possible Cause
Corrective Action
Pump does not start or run.
1. The switch is off.
2. There is a blown fuse or tripped breaker.
3. The pressure switch contacts are dirty.
4. The wires at the motor are loose or wired
incorrectly.
1. Turn the power switch on.
2. Replace the fuse or reset the circuit
breaker.
3. DISCONNET THE POWER. File or clean
the switch contacts.
4. DISCONNECT THE POWER.
Follow the wiring instructions to check and
tighten the wires.
Pump will not prime.
1. The pump was primed improperly or air is
trapped in the pipe.
2. There is an air leak.
3. The water level is below the suction pipe
inlet.
4. The foot valve is plugged or leaks.
1. DISCONNECT THE POWER. Adjust pump
height and make the pipe slope down to the
well. Remove the discharge tee and
re-prime.
2. Check all connections and fix the leakage.
3. Lower the suction pipe. If the water level is
more than 25 ft, use deep well installation.
4. Clean or replace the foot valve.
Pump operates but pumps
little or no water.
1. The foot valve is buried in sand or mud.
2. The ejector or impeller is plugged.
3. The foot valve or inlet strainer is clogged.
4. The water level is below the maximum lift
specification.
5. The voltage is not correct.
6. The pressure regulator is not set up
correctly.
1. Lift the suction pipe.
2. Clean the ejector or impeller.
3. Clean or replace as necessary.
4. Select a convertible jet pump.
5. Check the voltage switch.
6. Readjust the pressure regulator.
Pump starts and stops too
often.
1. The tank was pre-charged incorrectly.
2. There is a ruptured diaphragm/bladder
(pre-charged tank)/or has no air cushion.
3. The pipes are leaking.
4. The foot valve leaks.
5. The pressure switch is not adjusted
correctly.
6. The air charge is too low in the
pre-charged tank
1. Add or release air as needed.
2. Replace the tank/refill the air.
3. Repair the pipe connections or replace the
pipes.
4. Repair or replace the foot valve.
5. Closely look at the pressure gauge to see
the pump On/Off points are around
30 psi/50 psi. If not, adjust or replace the
pressure switch.
6. DISCONNECT POWER and open faucets
until all pressure is relieved. Using tire
pressure gauge, check air pressure in the
tank at the valve stem located on the tank. If
less than pressure switch cut-in setting (30
psi), pump air into the tank from an outside
source until air pressure is 2 psi less than the
cut-in setting of the switch. Check the air
valve for leaks (use soapy solution) and
replace core if necessary.
Pump does not shut off.
1. Water level is lower than estimated.
2. The pipes leak.
3. The pressure switch is not set correctly.
1. Use a deep well installation.
2. Locate and repair the leak or reconnect.
3. Reset or replace the pressure switch.

For Professional Technical Support call 1-844-242-2475 17
WARRANTY
Limited Warranty
WHAT THIS WARRANTY COVERS
When used and maintained in normal use and in accordance with the Owner’s Manual, your AQUAPRO product is
warranted against original defects in material and workmanship for at least one year (warranty varies depending on model;
see box for specific warranty information) from the date of purchase (the “Warranty Period”). During the Warranty Period,
AQUAPRO will repair or replace at no cost to you, to correct any such defect in products founds upon examination by
AQUAPRO to be defective in materials or workmanship.
WHAT THIS WARRANTY DOES NOT COVER
This Warranty does not cover:
Use of the product in a non-residential application, improper installation and/or maintenance of the product, damage due to
misuse, acts of God, nature vandalism or other acts beyond control of AQUAPRO, owner’s acts or omissions, use outside
the country in which the product was initially purchased and resale of the product by the original owner. This warranty does
not cover pick up, delivery, transportation or house calls. However, if you mail your product to an AQUAPRO Sales and
Service Center for warranty service, cost of shipping will be paid one way. This warranty does not apply to products
purchased outside of the United States, including its territories and possessions, outside of U.S. Military Exchange and
outside of Canada. This warranty does not cover products purchased from a party that is not an authorized retailer, dealer
or distributor of AQUAPRO products.
OTHER IMPORTANT TERMS
This warranty is not transferable and may not be assigned. This Warranty shall be governed and construed under laws of
the state of Michigan. The Warranty Period will not be extended by any replacement or repair performed under this Warranty.
THIS WARRANTY IS THE EXCLUSIVE WARRANTY AND REMEDY PROVIDED BY AQUAPRO. ALL OTHER
WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OR MERCHANTABILITY OR FITNESS FOR
PARTICULAR PURPOSE, ARE DISCLAIMED. IN NO EVENT WILL AQUAPRO BE LIABLE FOR ANY SPECIAL,
INDRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND OR NATURE TO OWNER OR ANY PARTY
CLAIMING THROUGH OWNER WHETHER BASED IN CONTRACT, NEGLIGENCE, TORT, OR STRICT PRODUCTS
LIABLITY OR ARISING FROM ANY CAUSE WHATSOEVER. Some states do not allow for the exclusion of consequential
damages, so the above exclusion may not apply to you. This warranty gives you specific rights. You may also have others
that vary from state to state.
Thank you for choosing an AQUAPRO product!

NOTICE D’UTILISATION
POMPE À JET CONVERTIBLE
Questions, problèmes, pièces manquantes? Avant de retourner au magasin, appelezle
Service àla clientèle AQUAPROdu lundi au vendredi, de 8 h à18 h,
heure normale de l’Est
1-844-242-2475
Modèle 63013/63023/63033

2 Pour une assistance technique professionnelle appelez 1-844-242-2475
PERFORMANCE
Modèle
HP
GPH d’eau @ Total de levage en pieds
Arrêt de
pression
maximale
5
pi.
10
pi.
20
pi.
30
pi.
40
pi.
50
pi.
60
pi.
70
pi.
80
pi.
90
pi.
100
pi.
110
pi.
63013
1/2
7.5
6.6
5.5
5.0
4.7
3.8
3.5
2.2
-
-
-
-
66PSI
63023
3/4
9.0
8.1
6.2
6.0
5.3
4.5
3.5
3.0
2
1.5
-
-
67PSI
63033
1
13.5
11.6
9.0
7.4
7.0
6.0
5.1
4.6
3.2
2
1.5
1
67PSI
Consignes de sécurité
1. Ne pas pomper de liquides inflammables ou explosifs comme de l’huile, de l’essence, du kérosène, de l’éthanol, etc.
Ne pas utiliser dans des lieux qui contiennent des vapeurs inflammables ou explosives. Le fonctionnement de cette
pompe avec ou près de liquides inflammables peut provoquer une explosion ou un incendie, entraînant des dommages
matériels, des blessures graves ou même la mort.
2. TOUJOURS débrancher la pompe avant de procéder à l’entretien.
3. Ne pas toucher le boîtier du moteur lorsqu’il fonctionne. Le moteur est conçu pour fonctionner à des températures
élevées. Ne pas démonter le boîtier du moteur.
4. Ne pas manipuler la pompe ni le moteur de la pompe lorsque vous avez les mains mouillés ou les pieds dans l’eau ou
dans un endroit humide ou détrempé.
5. Toujours porter des lunettes de sécuritélorsque vous travaillez avec une pompe.
6. Elle est aussi munie d'un moteur bitension, câblépour une tension de 230 volts (prédéterminée) ou de 115 volts, selon
la source d'alimentation.
7. Protéger le cordon d’alimentation de tout contact avec des objets tranchants, des surfaces chaudes, de l’huile ou des
produits chimiques. Éviter le tortillement du cordon. Ne pas utiliser un cordon d’alimentation endommagé ou usé.
8. Vérifier que la source d’alimentation électrique satisfait les exigences pour cette pompe.
9. Le non-respect des consignes relatives au fonctionnement de cet appareil peut être cause d’annulation de la garantie.
L’UTILISATION D’UNE POMPE ENDOMMAGÉE peut entraîner des dommages matériels, des blessures graves ou
même la mort.
10. La pompe doit être connectée àun disjoncteur de fuite de terre de 230 V/115 V protégépar un fusible ou un disjoncteur
de 10 A (230 V) / 20 A (115 V).
11. Bien connaître les différentes utilisations de la pompe, ses limites et les risques d’utilisation potentiels.
12. Fixez la pompe sur une base solide.
13. Inspectez régulièrement les composants de la pompe et du système. Débranchez la pompe de l'alimentation avant
d'inspecter.
14. Observez toutes les normes de sécurité et d’électricité, notamment le Code canadien de l’électricité et les exigences
sur la santéet sécuritéau travail en vigueur dans votre milieu de travail.
15. Le moteur de cette pompe est muni d’un protecteur thermique qui s’arrête si le moteur surchauffe. Le protecteur se
réinitialise automatiquement une fois que le moteur refroidit et qu’une température acceptable est atteinte. La pompe
peut démarrer de manière inattendue si l’appareil est branché.
16. Cette pompe est fabriquéde matériaux àhaute résistance mécanique et résistant àla corrosion. La durée de vie de la
pompe est prolongée lorsqu’elle est correctement installée, utilisée et entretenue. Cependant, une alimentation
électrique insuffisante, des saletés ou des débris peuvent provoquer une panne de la pompe. Veuillez lire
attentivement ce manuel et suivre les instructions relatives aux mesures correctives àprendre pour résoudre des
problèmes communs.