Aqua PRO ALL IN ONE Series User manual

ALL IN ONE SERIES
PUMP, FILTER &
UV CLARIFIER
- INSTRUCTIONS -
DATE
MAY 2022 v2.0
MODEL
03AS310
03AS311
WWW.AQUAPROONLINE.COM.AU
HOTLINE    PHONE +   
EMAIL [e-mail]
AQUAPRO All In One Series Instructions.indd 1AQUAPRO All In One Series Instructions.indd 1 16/5/2022 8:37 am16/5/2022 8:37 am

HOTLINE [phone] PHONE [phone] EMAIL [e-mail] WEB WWW.AQUAPROONLINE.COM.AU
CONGRATULATIONS ON YOUR PURCHASE
OF THIS PRODUCT BY AQUAPRO.
TECHNICAL SPECIFICATIONS
• Mechanical & Biological Filtration
• 5W/9W Ultraviolet Clarifier for green water
clarification.
• Powerful 1000/2000 L/hour pump with wear
resistant ceramic components
• Dual Flow Control T-Piece
• Multiple fountain nozzles help aeration of water
• 12V Low Voltage Power System for safe in-pond
operation.
DESCRIPTION ALL IN ONE 1000 ALL IN ONE 2000
TRANSFORMER 240V / 12V 240V / 12V
POWER CONSUMPTION* 24W 72W
UV-CLARIFIER POWER 5W 9W
MAX HEAD 1.6M 2M
WATER FLOW 1000 L/H 2000 L/H
IP RATING TRANSFORMER IP65 IP65
IP RATING PUMP & UVC IPX8 IPX8
OUTLET THREAD SIZE 1/2IN (MALE) 1/2IN (MALE)
* SUBJECT TO VARIATION ACCORDING TO LOAD.
Please read these instructions and familiarise yourself with the equipment before placing it in service. Correct and safe use of the
system requires strict compliance with the safety instructions. For safety reasons persons less than 16 years of age or people that are
not familiar with these instructions should not use this equipment.
BENEFITS
PRODUCT SPECIFIC SAFEGUARDS
THE AQUAPRO ALL IN ONE SERIES COMPLETE POND AND FILTER SYSTEM IS DESIGNED TO
CLEAN POND AND WATER FEATURE WATER UTILISING THE LATEST ADVANCED TECHNOLOGY.
• Do not look at an unshielded UV-C globe. Ultra
Violet light is harmful to your eyes and may cause
blindness. Do not operate UV Globe out of the
housing.
• As the UV Clarifier Globe is made of quartz glass,
please avoid sudden jolts, as this will break the quartz.
• In cold temperatures where frost or freezing may
occur, please cease to use the unit. Remove from the
environment. Frozen water will crack the Quartz glass
sleeve.
AQUAPRO All In One Series Instructions.indd 2AQUAPRO All In One Series Instructions.indd 2 16/5/2022 8:37 am16/5/2022 8:37 am

HOTLINE [phone] PHONE [phone] EMAIL [e-mail] WEB WWW.AQUAPROONLINE.COM.AU
ALL-IN-ONE SERIES
INSTRUCTIONS
To guard against injury, basic safety precautions should
be observed including, but not limited to the following:
• The pump should only be used in clean water. Do
not use the pump in any solvent or gasoline that is
flammable.
• Any damage of the equipment or unmerited
operation will bring dangerous UV Rays to the skin
and eyes. If there is any damage to the equipment, it
must not to be used. The equipment should be placed
out of reach of children.
• For your own safety, disconnect from the power
supply before any maintenance of any equipment is
attempted on the tank or water body.
• Be sure the equipment is submerged completely in
the water. The depth should not exceed 2m.
• Do not operate the pump if the appliance or any
components of the system, such as the power cable,
have been damaged.
• Always use a properly grounded power supply that is
connected to an RCD with a rated residual operating
current not exceeding 30mA. As per AS/NZS
3350.2.41:1997
• The drip loop method should be used to prevent water
from traveling down the cable and onto the plug or
power supply. If the plug does get wet, do not unplug
the cable. Disconnect the circuit breaker that supplies
power to the power supply point. Then unplug and
examine the plug and power supply point for presence
of water. If the power point has become wet, you
should consult an electrician before using the power
point again.
• Always unplug the pump from the power supply when
not in use or before performing any maintenance
on the pump or in the pond. Never pull the cable to
disconnect the plug from the power supply. Grasp the
plug and pull to disconnect.
• If required, have a qualified electrician install a
weatherproof power supply point near to the pond
or water-feature (within the cable length of the
appliance).
• Do not install or store the appliance where it will be
exposed to extreme hot or cold temperatures. Do not
use in water above 35°C.
• Do not cut the cable as this will result in voiding your
warranty.
• Care should be taken to arrange the power cable so
that it cannot be accidentally tripped over or pulled.
• Do not attempt to repair the electrical appliance
yourself. Return to an authorised service centre
or place of purchase if a fault occurs, regular
maintenance is not considered repair and is required
by user.
IMPORTANT SAFEGUARDS
Once a fountain nozzle has been selected, assemble the fountain kit as per the attached diagram. Screw the T-piece
onto the pump outlet, adjust the telescopic riser to the desired height and align vertically. On the Dual-control flow
adjuster, on the T-piece, you can vary the flow between the fountain head and the waterfall outlet. Close the second
outlet of the T-piece if this is not required for an optional waterfall.
Position the device in the pond horizontally, on a solid base free from sludge, in such a way that it is fully covered with
water and the fountain kit protruding out of the water.
Insert the two pin Low Voltage plug into the Low Voltage side of the transformer and secure with the locking nut.
Insert the mains power supply plug into the power outlet.
Note: Use the power supply switch for turning the unit on and o.
INSTALLATION
AQUAPRO All In One Series Instructions.indd 3AQUAPRO All In One Series Instructions.indd 3 16/5/2022 8:37 am16/5/2022 8:37 am

HOTLINE [phone] PHONE [phone] EMAIL [e-mail] WEB WWW.AQUAPROONLINE.COM.AU
FOUNTAIN KIT
1
2
3
4
5
6
7
8
9
10
13
14
15
16
17
18
19
20
12 11
NOTE:
PLEASE CONSULT YOUR RETAILER FOR QUALITY
ORIGINAL AQUAPRO REPLACEMENT PARTS FOR
YOUR AQUAPRO PRODUCT.
VISIT WWW.AQUAPROONLINE.COM.AU FOR NEAREST STOCKISTS.
PARTS DESCRIPTION FIG.1
1. 20MM HOSE TAIL 2. FILTER COVER 3. BIO SPONGE 4. UVCLARIFIER UNIT 5. PUMP SUCTION
ELBOW 6. FILTER MEDIA BOXES 7. FILTER MEDIA MOUNTING PLATE 8. FILTER BASE WITH
CLIPS 9. 1/2” PUMP THREADED ADAPTER 10. WATER PUMP 11. FOUNTAIN HEAD BELL NOZZLE
12. FOUNTAIN HEAD COURSE DAISY NOZZLE 13. FOUNTAIN HEAD FINE DAISY NOZZLE
14. FOUNTAIN NOZZLE MOUNT 15. INTERNAL EXPANDABLE RISER 16. ORING 17. EXTERNAL
EXPANDABLE RISER 18. BALL JOINT LOCKING NUT 19. RISER TO TPIECE ADAPTER 20. DUAL
CONTROL TPIECE ADAPTER
AQUAPRO All In One Series Instructions.indd 4AQUAPRO All In One Series Instructions.indd 4 16/5/2022 8:37 am16/5/2022 8:37 am

HOTLINE [phone] PHONE [phone] EMAIL [e-mail] WEB WWW.AQUAPROONLINE.COM.AU
ALL-IN-ONE SERIES
INSTRUCTIONS
1 2 3 4 5 6
1 2 3 4 5 6 7 8 9
PUMP FIG.2
UVC FIG.3
1. IMPELLOR COVER 2. RUBBER GROMMET 3. IMPELLOR 4. 0RING
5. CERAMIC IMPELLOR SHAFT 6. PUMP MOTOR BODY
1. IUV LIGHT CASING 2. WATER FLOW SPIRAL 3. QUARTZ GLASS SLEEVE 4. QUARTZ SLEEVE
LOCKING NUT 5. 45MM X 4MM ORING 6. PLASTIC QUARTZ SLEEVE HOLDER 7. 60MM X 3.1MM
ORING 8. 9W LOW VOLTAGE UVC GLOBE 9. UVC LAMP HOLDER WITH CABLE
AQUAPRO All In One Series Instructions.indd 5AQUAPRO All In One Series Instructions.indd 5 16/5/2022 8:37 am16/5/2022 8:37 am

HOTLINE [phone] PHONE [phone] EMAIL [e-mail] WEB WWW.AQUAPROONLINE.COM.AU
PROBLEM REASON SOLUTION
WATER PUMP NOT
WORKING NO POWER CHECK THAT THE PLUG IS CONNECTED
AND TURNED ON
SPONGES AND FILTER MEDIA
BLOCKED WITH SLUDGE CLEAN THE SPONGES AND FILTERS
IMPELLOR IS BLOCKED WITH
SLUDGE OR LIMESCALE
CLEAN THE IMPELLOR AS PER
THE INSTRUCTIONS
RUNNING WITHOUT SUFFICIENT WATER SUBMERSE THE EQUIPMENT UNDERWATER
THEN PLUG IN. REFILL IF NECESSARY.
BLOCKED IMPELLOR CHAMBER OR CERAMIC
SHAFT IS BROKEN
CLEAN THE IMPELLOR. CHECK FOR WEAR.
REPLACE IF NECESSARY.
WATER PUMP IS NOISY BLOCKAGE IN PUMP CLEAR THE BLOCKAGE
IMPELLOR & SHAFT WORN OUT REPLACE IMPELLOR & SHAFT
IMPELLOR BROKEN REPLACE IMPELLOR
WATER VALVE CLOSED ON THE OUTLET OPEN THE VALVE AND ALLOW
WATER TO FLOW
UNIT INLET IS BLOCKED OR THE WATER PUMP
INLET IS BLOCKED CLEAR ALL BLOCKAGES
UVC LAMP IS
NOT WORKING
UVC GLOBE BLOWN OR
QUARTZ SLEEVE BROKEN REPLACE AS NECESSARY
CONNECTION OF THE UVC GLOBE
NOT SUFFICIENT
PUSH UV GLOBE IN FIRMLY UNTIL YOU HEAR
A CLICK SOUND
SPARE PARTS NOTE: THESE ARE THE MOST USED
TROUBLESHOOTING
DESCRIPTION MODEL 1000 MODEL 2000
IMPELLOR & SHAFT 11AQ110 11AQ111
LOW VOLTAGE UV GLOBE 5W / 9W 11AU972 11AU177
QUARTZ GLASS SLEEVE 11AQ210 11AQ211
SPONGE FILTER 11AQ310 11AQ311
COMPLETE FOUNTAIN KIT 11AQ410 11AQ411
12V TRANSFORMER 48VA / 72VA 04ST048 04ST072
AQUAPRO All In One Series Instructions.indd 6AQUAPRO All In One Series Instructions.indd 6 16/5/2022 8:37 am16/5/2022 8:37 am

HOTLINE [phone] PHONE [phone] EMAIL [e-mail] WEB WWW.AQUAPROONLINE.COM.AU
ALL-IN-ONE SERIES
INSTRUCTIONS
PRODUCT SPECIFIC SAFEGUARDS
• The pump is designed to be used in a Fresh water Garden pond. It is not to be used in any other manner or purpose.
The pump should only be used in clean water.
• AQUAPRO Filtration & Waterfall Pumps are cooled by water flowing through the inside of the motor body. If
the pump flow becomes restricted it will overheat and could cause permanent damage. Large tubing size is strongly
recommended to deliver adequate water flow to cool the pump. The pump needs to be cleaned regularly to prevent
the pump becoming blocked, thus causing the pump to overheat and burn out. This is not a warrantable event. It
is strongly recommended not to choose an appropriate sized pump that is too small for the Job required. The flow
rate through the pump needs to be strong enough so that a half of the rated max flow is kept running at all times.
CLEANING
• To remove cage, pull plastic tabs on both sides and lift
the cage o.
• Take out the filter sponge and filter media boxes and
clean. It is recommended this is done in a bucket of
pond water to ensure good bacteria are not killed by
the Chlorine in tap water. Check for wear and tear of
the sponges. Replace if necessary.
• Maintain the filter sponge regularly according to how
quickly the sponge gets clogged up. When the flow
starts to get reduced check and clean if necessary.
• You can help boost the biological function of your
filter with a bacterial additive available from your local
stockist.
• The UV lamp should be replaced regularly at the end
of its design life. Usually this around 11 months of use.
To take out the UV clarifier globe, open the safety
catch on the side and turn the UV Clarifier casing in
anti-clockwise direction to the stop position. Then
slide out the 5W/9W LV quartz glass globe. Now you
can change your UV lamp.
• Dirt on the Quartz sleeve will influence the
eciencies of the equipment. Please remove and
clean regularly.
• To clean the quartz glass sleeve, take the quartz sleeve
out by unfastening the locking nut (No. 4 Fig. 3).
Then you can take out the quartz glass sleeve and
clean.
• To maintain the impellor of the pump, turn the
Impellor cover in an anti-clockwise direction to the
stop position, and then you can separate the impellor
cover and pump body. Take out the impellor, clean it
with clean water and suitable brush. Inspect for signs
for wear. Replace if necessary.
• Once the cleaning and inspection process is
completed, reassemble in the reverse manner.
The pump suction elbow is pushed firmly onto the
impellor cover inlet of the pump. Pay attention to the
UV clarifier casing when inserting it back together.
BEGIN BY ENSURING THAT THE MAINS POWER SUPPLY IS DISCONNECTED BEFORE
ATTEMPTING ANY MAINTENANCE OR ADJUSTMENT OF THE UNIT. REMOVE THE UNIT FROM
THE WATER. THE FILTERS AND SPONGES IN THIS UNIT WILL CLOG OVER TIME. TAKE OFF THE
FOUNTAIN SET FIRST, AND THEN OPEN THE TWO CLIPS ON THE SIDE OF THE FILTER COVER.
AQUAPRO All In One Series Instructions.indd 7AQUAPRO All In One Series Instructions.indd 7 16/5/2022 8:37 am16/5/2022 8:37 am

WARRANTY
IMPORTANT: IF USED IN MARINE OR SALTWATER, DUE TO THE HARSH CONDITIONS THE
WARRANTY IS VOID.
WARRANTY COVERS ONLY APPLIANCE DEFECTS, FAULTY MATERIAL AND WORKMANSHIP
WITHIN A 2 YEAR PERIOD.
• Faults arising due to; accidents, misuse, not following manufacturer’s guidelines/instructions, or power surges/
spikes/brownouts will not be covered.
• The impellor set is a consumable item and is therefore not covered under warranty.
• Warranty will be void if any tampering, removal of warranty labels, or electrical circuitry is evident.
• Warranty will be void if the power cord is cut or damaged in any way.
• Warranty will be void if any visible signs of overheating are present.
• Loss of livestock, damage to property or personal injury caused by this product will not be covered.
• Warranty claims caused by installation faults will not be covered.
• It is the customer’s responsibility to return the faulty appliance for any warranty claim to Aquatec.
• For any warranty to be valid, an original proof of purchase must be provided.
• Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled
to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure.
FOR MORE INFORMATION AND THE COMPLETE AQUAPRO RANGE
VISIT WWW.AQUAPROONLINE.COM.AU
WWW.AQUAPROONLINE.COM.AU
HOTLINE    PHONE +   
EMAIL [e-mail]
AQUAPRO All In One Series Instructions.indd 8AQUAPRO All In One Series Instructions.indd 8 16/5/2022 8:37 am16/5/2022 8:37 am