Aqua PRO 63043 User manual

OWNER’S MANUAL
CONVERTIBLE JET PUMP WITH 6 U.S. GALLON TANK
Questions, problems, missing parts? Before returning to the store call AQUAPRO
Customer Service 8 a.m. - 6 p.m., EST, Monday-Friday
1-844-242-2475
© 2017 Copyright GP Enterprises Co., Ltd.
Model 63043

2
PERFORMANCE
Model HP
GPH of Water @ Total Discharge Pressure of
40psi
Max. Pressure shutoff
5’ 10’ 20’ 30’ 40’ 50’ 60’ 70’
63043 1/2 450 396 330 300 282 228 210 132 66PSI
SAFETY INSTRUCTIONS
1. Do not pump flammable or explosive liquids such as oil, gasoline, kerosene, ethanol, etc. Do not use in the presence of
flammable or explosive vapors. Using this pump with or near flammable liquids can cause an explosion or fire, resulting
in property damage, serious personal injury, and/or death.
2. ALWAYS disconnect the power to the pump before servicing.
3. Do not touch the motor housing during operation. The motor is designed to operate at high temperatures. Do not
disassemble the motor housing.
4. Do not handle the pump or pump motor with wet hands or when standing on a wet or damp surface, or in water.
5. Wear safety goggles at all times when working with pumps.
6. This is a dual voltage 115/230 V pump.VOLTAGE SELECTOR INSIDE PRESET TO 230V.For 115V selection, please
open the terminal cover and set the switch to the proper voltage. All wiring should be performed by a qualified
electrician.
7. Protect the electrical cord from sharp objects, hot surfaces, oil, and chemicals. Avoid kinking the cord. Do not use
damaged or worn cords.
8. Ensure the electrical power source is adequate for the requirements of the pump.
9. Failure to comply with the instruction and designed operation of this unit may void the warranty. ATTEMPTING TO USE
A DAMAGED PUMP can result in property damage, serious personal injury, and/or death.
10. The pump should be connected to a 230V/115V GFCI outlet protected with a 10 amp(230V)/20 amp(115V) fuse or
circuit breaker.
11. Know the pump and its applications, limitations, and potential hazards.
12. Secure the pump to a solid base.
13. Periodically inspect the pump and system components. Disconnect the pump from the power supply before inspecting.
14. Follow all local electrical and safety codes, along with the National Electrical Code (NEC). In addition, all Occupational
Safety and Health Administration (OSHA) guidelines must be followed.
15. The motor of this pump has a thermal protector that will trip if the motor becomes too hot. The protector will reset itself
once the motor cools down and an acceptable temperature has been reached. The pump may start unexpectedly if it is
plugged in.
16. This pump is made of high-strength, corrosion-resistant materials. It will provide trouble-free service for a long time
when properly installed, maintained, and used. However, inadequate electrical power to the pump, dirt, or debris may
cause the pump to fail. Please carefully read the manual and follow the instructions regarding common pump problems
and remedies.

3
PRE-INSTALLATION
APPLICATION
This unit is a convertible jet pump designed for pumping water where the water is located less than 70 feet. If the water level
to the pump is deeper than 70 feet, a deep well submersible pump should be selected. A pressure switch pre-set at 30 psi
“on”/50 psi “off” has been installed on the pump. The pressure switch can automatically turn on and off the pump based on
the system pressure.
TOOLS REQUIRED
SPECIFICATIONS
POWER SUPPLY 115V/230V,60HZ,20/10Amp circuit
LIQUID TEMP. RANGE
32°F to 77°F (0°- 25°C)
DISCHARGE 1in. FNPT
SUCTION
1 1/4FNPT
SHALLOW WELL WATER LEVEL 25 ft.
DEEP WELL WATER LEVEL 70 ft.
Phillips
Screwdriver
Flathead
Screwdriver
Thread Tape
Tape Measure
Safety goggles
Pipe wrench Hacksaw
PVC glue

4
PACKAGE CONTENTS
Part Description Quantity Part Description Quantity
A
Pump
1
H
Pressure regulator
1
B
Tank
1
I
Pressure tube
1
C
Discharge tee
1
J
Pressure gauge
1
D
Stainless steel
braided hose
1 K Flat washer 4
E
Rubber Washer
1
L
Bolt
2
F Venturitube (#11) 1 M Spring washer 2
G Nozzle (#01) 1 N Nut 2
PRE-INSTALLATION
Determine the depth of your well
Tiea small but heavy weight such as a fishing weight to the end of a piece of cotton string. Lower the weight into the well until
it reaches the bottom of the well. Make a mark on the string at ground level. Pull the weight out of the well and measure from
the bottom of the weight to the ground level mark. This is the depth of your well. Subtract five feet from the depth of your well.
If this number is less than 25 feet, shallow well installation should be taken. If this number is more than 25 feet and less than
70 feet, deep well installation should be taken. If this number is more than 70 feet, a deep well submersible pump should be
selected.Measure the ground level mark to the mark where the cotton string is wetted. This number is your well’s water level.
Lower the pipe into the well until the strainer is five feet above the bottom of the well. It should also be at least 10 feet below
the well’s water level while the pump is running in order to prevent the pump from sucking air due to water level drawdown.
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and
hardware contents above. If any part is missing or damaged, do not attempt to assemble the product. Contact customer
service for replacement parts.
LOCATION OF THE PUMP
Decide on the area for the pump installation. Select a pump location with adequate space for future pump maintenance. It
can be located inthe basement or utility room of the house, at the well, or between the house and the well. If installed outside
of the house, it should be protected by a pump house with auxiliary heat to prevent possible freezing. Protect the pump

5
against flooding and excess moisture. The well also should be protected for sanitary reasons. Mount the pump as close to
the well as possible.
TANK - PRE-CHARGED STORAGE
The 6 gallons pre-charged storage tank has a flexible bladder that acts as a barrier between the compressed air and water.
This barrier prevents the air from being absorbed into the water and allows the water to be acted on by compressed air at
initially higher than atmospheric pressures. The pressure was pre-set as 28 psi in the factory. If the air pressure less than 28
psi, you may need to pump air into the tank before you start the pump.
For wells 25 feet or less in depth, shallow well installations should be adapted. The shallow well
installations have only one single pipe between the pump and well water.
SHALLOW WELL INSTALLATION
MATERIALS REQUIRED (NOT INCLUDED)
One can PVC cement & primer (read instructions carefully) One well seal with vent plug
One can thread compound (read instructions carefully) Foot valve
Teflon tape Discharge tee/Priming tee and plug
Rigid pipe Relief valve
Check valve Adaptor
Flexible plastic pipe/clamps Tank(for AUTO series tank is included）
Tank tee
WARNING: All joints and connections must be AIRTIGHT. Asingle leak will prevent the proper operation of the pump. Wrap
thread tape clockwise on all threaded connections. For all non-threaded connections, you must use PVC Purple Primer and
PVC Cement to ensure airtight seals. Measure all pipe lengths before attaching.
NOTE: Afoot valve is a check valve that is used to keep the water from running back into the well from the pump and
maintain hydraulic pressure when the pump is not running. If the foot valve does not hold the water the pump will lose it’s
prime and will not pump water. If the foot valve open pressure is too high (the spring is too stiff), or the flow area is too small,
the pump suction head and flow rate will significantly drop.
NOTE: The suction pipe size should not be less than 1-1/4 in. The suction size of this pump is 1-1/4 in. FNPT.
CAUTION: To avoid skin burns, unplug the pump and allow time for it to cool after periods of extended use.

6
PRE-INSTALLATION FOR TANK
1. Wrap discharge tee (C) with thread tape (sold separately) and thread it on pump (A) outlet.
2. Wrap thread of stainless steel braided hose (D) with thread tape and thread into the level outlet on the discharge tee (C).
3. Thread flat washer (K) onto bolt (L) and attach pump to tank. Secure bolt (L) with another flat washer (K), spring washer
(M), and nut (N) Repeat this on the other side of the pump.

7
4. Insert rubber washer (E) into open end of the stainless steel braided hose (D). Thread hose (D) onto front of tank (B).
Hand tighten, and then tighten with wrench 1/2 turn.
Cased Well Installation, 2” or Larger Casing
1. Install the pressure gauge in the pump body.
2. Mount the pump as close to the well as possible.
3. Assemble the foot valve, strainer, and well pipe. Make
sure that the foot valve works freely.
4. Lower the pipe into the well until the strainer is five feet
above the bottom of the well. It should also be at least 10
feet below the well’s water level while the pump is running
in order to prevent the pump from sucking air. Install a
sanitary well seal.
5. Install a priming tee, priming plug, and suction pipe to
the drop pipe.
If the distance from the well to the pump is substantial,
add a priming tee at the pump. Connect the pipe from the
well to the pump suction port, using the fewest possible
fittings – especially elbows – as fittings increase friction in
the pipe. The suction pipe should be at least as large as
the suction port on the pump. Support the pipe so that there are no dips or sags in the pipe, so it doesn’t strain the pump
body, and so that it slopes slightly upward from the well to the pump (high spots cancause air pockets which can air lock
the pump). Seal the suction pipe joints with PTFE pipe thread sealant tape or a PTFE-based pipe joint compound. Joints
must be air- and water-tight. If the suction pipe can suck air, the pump cannot pull water from the well.
You have just completed the suction piping for your new shallow well jet pump. Please go discharge pipe and tank
connections.

8
Discharge Pipe Connection
1. Install a tee in the pump discharge port.
2.Connect the tee to your water system in the house.
You have just completedconnection for your jet pump. Please goto electrical hookup.
Priming
CAUTION: Risk of burns. Never run pump dry. Running pump without water may cause pump to overheat, damaging seal
and possibly causing burns to persons handling pump. Fill pump with water before starting.
WARNING: Risk of explosion and scalding. Never run pump against closed discharge. To do so can boil water inside
pump, causing hazardous pressure in unit, risk of explosion and possibly scalding persons handling pump.
1. Fill the pump through the pump outlet, fill all piping between the pump and the well, and make sure that all piping in the
well is full. If you have also installed a priming tee in the suction piping, remove the plug from the tee and fill the suction
piping.
2. Replace all fill plugs.

9
Electrical
WARNING: It is recommended all electrical work be performed
by a licensed electrician.
WARNING: Before wiring the pressure switch, turn off the power
source to which you are connecting to avoid potentially life
threatening electrical shock.
WARNING: When wiring from the power source to the pressure
switch, it is recommended that you use either a 14-gauge or
12-gauge cord.To complete the installation, you must connect
the power source to the pressure switch. A 30/50 psi pressure
switch has been installed on the pump. The pressure switch allows for automatic operation; the pump starts when pressure
drops to the “cut-in” setting (30 psi pre-set).
To wire the pressure switch:
Remove the pressure switch cover on the pump to expose the wiring terminals.
Connect the green ground wire of the power supply to the switch ground terminal.
Connect the power supply wires to the two outside terminals marked “LINE” and replace the switch cover.
CAUTION:Do NOT use a pressure switch set at a pressure greater than 50 psi. The pump will not create pressures
greater than 50 psi, if so the pump will never shut off, resulting in damage to the pump and voiding the warranty.
Voltage Setting
This pump is pre-wired at 230 volts.
If the power source is 115 volts, remove the electrical housing
cover.
Flip the switch to 115 volts. Replace the cover.
NOTE: All electrical work should be performed by a licensed
electrician.
Start the Pump
1. Power on! Start the pump. The pump should pump water in two or three minutes.
2. If you don’t have water after 2 or 3 minutes, stop the pump and remove the fill plugs. Refill the pump and piping. You may
have to repeat this two or three times in order to get all the trapped air out of the piping.
The control valve remains open throughout this procedure.
3. After the pump has built up pressure in the system and shut off, check the pressure switch operation by opening a faucet
or two and running enough water out to bleed off pressure until the pump starts. The pump should start when pressure drops
to 30 PSI and stop when pressure reaches 50 PSI. Run the pump through one or two complete cycles to verify correct
operation. This will also help clean the system of dirt and scale dislodged during installation.
Congratulations on a successful installation.
If you were unsuccessful, please refer to Troubleshooting or call ourcustomer service technical staff.

10
DEEP WELL INSTALLATION INSTRUCTIONS
MATERIALS REQUIRED (NOT INCLUDED)
One can PVC cement & primer (read instructions
carefully)
One well seal with vent plug
One can thread compound (read instructions
carefully)
Foot valve
Teflon tape Discharge tee/Priming tee and plug
Rigid pipe Relief valve
Check valve Adaptor
Flexible plastic pipe/clamps Tank
Elbow Tank tee
Nipple
WARNING: All joints and connections must be AIRTIGHT. A single leak will prevent the proper operation of the pump. Wrap
thread tape clockwise on all threaded connections. For all non-threaded connections, you must use PVC Purple Primer and
PVC Cement to ensure airtight seals. Measure all pipe lengths before attaching.
NOTE: A foot valve is a check valve that is used to keep the water from running back into the well from the pump and
maintain hydraulic pressure when the pump is not running. If the foot valve does not hold the water the pump will lose it's
prime and will not pump water. If the foot valve open pressure is too high (the spring is too stiff), or the flow area is too small,
the pump suction head and flow rate will significantly drop.
CAUTION: To avoid skin burns, unplug the pump and allow time for it to cool after periods of extended use.
1. Remove the bolts from the pump body and take out the ejector from the pump.
2.Remove the venturi tube (#12), and then use a 5/8 inch socket to unscrew the nozzle (#03) counter clockwise.

11
3. Wrap thread tape on the threads of the venturi tube threads (#11) and nozzle threads (#01). Use the 5/8 inch socket to
thread the nozzle (#01) in the ejector, thread the venturi tube (#11) in the ejector.
4. Assembly the tank with pump together. Align a bolt (L), a flat washer (K), tank hole, pump foot hole, spring washer(M), and
another flat washer. Use the nut(N) to secure the bolt. Repeat this on the other side of the pump.
5. Remove the air stem cover from the back of the tank (B).
6. Using tire pressure gauge, check air pressure in tank at valve stem located on the back of the tank (B).

12
Air pressure in the tank (B) must be 2 psi lower than the "cut-in" of the pressure switch.
NOTE: The pump (A) has a 30/50 psi pressure switch, which means the "cut-in" is 30 psi; therefore, the tank (B) needs to be
set to 28 psi. To check the pressure in the tank (B), use a tire pressure gauge (not included). If more air is needed, add air to
the tank with a tire pump or air compressor. If less is needed, bleed out some air.
7. Mount the pump as close to the well as possible.
8. Connect two pipes (1” drive, 1-1/4” suction) to the ejector and lowerthe ejector into the well until it is five feet from the
bottom. It shouldalso be at least 9 feet below the well’s water level while the pump isrunning in order to prevent the pump
from sucking air.
10. Install a sanitary well seal and connect the ejector piping to the pump.Use steel nipples through the well seal with flexible
poly pipe to avoidcrushing the plastic pipe when tightening the seal.
11. Support the pipe so that there are no dips or sags in the pipe, so itdoesn’t strain the pump body, and so that it slopes
slightly upwardfrom the well to the pump (high spots can cause air pockets which canair lock the pump). Seal the suction
pipe joints with PTFE pipe threadsealant tape or a PTFE-based pipe joint compound. Joints must be airandwater-tight. If the
suction pipe can suck air, the pump cannot pullwater from the well.
You have just completed the plumbing for your new double pipe deep welljetpump. Please go to priming.
12. Pull out the pressure tube from the 90° elbow insert. Unthread and remove the elbow insert from the pump body.

13
13. Wrap the threads of the 1/4 in. pressure gauge (included) or plug with thread tape and thread it tin the elbow insert hole.
Cut off the expanded portion of the pressure tube.
14. Fill the pipe with water until water overflows. Replace the plug back to the tee.
NOTE: It may take several minutes to fill the pipes and the pump completely.
NOTE: If the pump does not hold its prime, inspect all pipes and connections for leaks, and repair the leaks.
15. Wrap thread tape around the threads of a 1 in. pressure regulator (included). Using a pipe wrench, thread the 1 in.
pressure regulator into the top of the pump (A).
NOTE: This pressure regulator is a normally-closed valve installed at the discharge of the pump to provide an obstruction to
flow and thereby regulate the pump pressure and provide back pressure for the ejector. Failure to use this item may result in
a loss of prime and/or a low pressure.
16a. Thread the 1/4 in. elbow insert (included in regulator kit) into the 1/4 in. hole on the side of the pressure regulator.

14
b. Slide the pressure tubing (attached with the pump pressure switch) over the 1/4 in. brass elbow and the pressure switch
connector.
17. Wrap the threads of the thread adaptor 3/4 in. MNPT x 1 in. FPT with thread tape. And thread the adaptor in pressure
regulator. Wrap the threads of the discharge tee (included) with thread tape and thread the discharge tee in the 1 in. FPT
adaptor.
18. Connect the stainless steel braided hose from the tank to discharge tee.
NOTE: Make sure to put the rubber washer (Included) in the bottom of the thread nut on the hose.
19. Wrap the threads of the 1 in. MNPT x 1 in. slip PVC adaptor with thread tape and thread the adaptor in the discharge tee.

15
Cement as many sections and couplings of rigid 1" PVC pipe needed to connect the 1 in. MNPT slip PVC adaptor. Connect
the tank to your water system in the house.
20. This pump is pre-wired at 230 volts. If the power source is 115 volts, remove the electrical housing cover. Flip the switch
to 115 volts. Replace the cover.
NOTE: All electrical work should be performed by a licensed electrician.
21. Turn the regulator adjustment screw down tight. Turn on pump. If the pump is properly primed, a high pressure will
immediately show on the pressure gauge. With the pump operating at high pressure, slowly unscrew the adjusting screw
until maximum water flow is obtained without dropping to zero. If pressure falls completely, retighten the screw and readjust.
If no pressure shows, stop the pump, remove the pressure regulator from pump, add more water, and try again. After the
adjusted bolt is set up, lock the screw nut on the bolt. The pump is ready for use.
NOTE: The pressure regulator screw is very tight. A big screw driver needed.

16
CARE AND MAINTENANCE
WARNING: Disconnect power and release all pressure from the system before attempting to install, service, relocate or
perform any maintenance.
DRAINING THE PUMP
Drain openings are provided on all models. To drain the pump: 1.Remove drain plug (see left photo. located on
the side of pump) and air plug (located on the
top of the pump close to the outlet hole) to vent
the system.
2. Drain all piping to a point below the freeze
line.
NOTE: While this will drain the pump, it will not
necessarily drain all the unprotected parts of the
piping system. To drain tank, disconnect the
piping at the tank outlet.
TROUBLESHOOTING
Problem
Possible Cause
Corrective Action
Pump does
not start or run 1. Switch off 2. Blown fuse or tripped breaker
3. Pressure switch contacts are dirty
4. Wires at motor are loose or wiring incorrectly
1. Turn power switch on
2. Replace fuse or reset circuit breaker
3. DISCONNET THE POWER. File or clean
the switch contacts
4. DISCONNECT THE POWER.
Following wiring instructions check and
tighten wires.
Pump will not
prime
1. Improper priming or air trapped in the pipe
2.Air leak
3.Water level below suction pipe inlet
4. Foot valve is plugged or leaks
1. DISCONNECT THE POWER. Adjust pump
height and make the pipe slope down to the
well. Remove the discharge tee and re-prime
2. Check all connections and fix the leakage.
3. Lower suction pipe. If the water level is
more than 25ft, use deep well installation.
4. Clean or replace foot valve
Pump operates
but pumps little or
no water
1. Foot valve is buried in sand or mud
2. Ejector or impeller is plugged
3. Foot valve or inlet strainer clogged
4. Water level below maximum lift specification
5. Improper voltage
6. Pressure regulator set-up improperly
1. Lift the suction pipe
2. Clean the ejector or impeller
3. Clean or replace as necessary
4. Select a convertible jet pump
5. Check voltage switch
6. Readjust the pressure regulator

17
Problem
Possible Cause
Corrective Action
Pump starts and
stops too often
1. Incorrect tank pre-charged
2. Ruptured diaphragm/bladder
(pre-charged tank)/or has no air cushion
3. Pipes leak
4. Foot valve leaks
5. Improperly adjusted pressure switch
6. Air charge too low in pre-charged tank
1. Add or release air as needed
2. Replace tank/refill air
3. Repair pipes connection or replace pipes
4. Repair or replace the foot valve
5. Closely look at the pressure gauge to see
the pump On/Off points are around 30 psi/50
psi, if not, adjust or replace the pressure
switch
6. DISCONNECT POWER and open faucets
until all pressure is relieved. Using tire
pressure gauge, check air pressure in tank
at valve stem located on the tank. If less
than pressure switch cut-in setting (30 psi),
pump air into tank from outside source until
air pressure is 2 psi less than cut-in setting
of switch. Check air valve for leaks (use
soapy solution) and replace core if
necessary.
Pump does not
shut off 1. Water level is lower than estimated 2. Pipes leak
3. Improper setting of pressure switch
1. Use deep well installation
2.Locate and repair leak or reconnect
3. Reset or replace pressure switch

18
WARRANTY
Limited Warranty
WHAT THIS WARRANTY COVERS
When used and maintained in normal use and in accordance with the Owner’s Manual, your AQUAPRO product is
warranted against original defects in material and workmanship for at least one year (warranty varies depending on model;
see box for specific warranty information) from the date of purchase (the “Warranty Period”). During the Warranty Period,
AQUAPRO will repair or replace at no cost to you, to correct any such defect in products founds upon examination by
AQUAPRO to be defective in materials or workmanship.
WHAT THIS WARRANTY DOES NOT COVER
This Warranty does not cover:
Use of the product in a non-residential application, improper installation and/or maintenance of the product, damage due to
misuse, acts of God, nature vandalism or other acts beyond control of AQUAPRO, owner’s acts or omissions, use outside
the country in which the product was initially purchased and resale of the product by the original owner. This warranty does
not cover pick up, delivery, transportation or house calls. However, if you mail your product to an AQUAPRO Sales and
Service Center for warranty service, cost of shipping will be paid one way. This warranty does not apply to products
purchased outside of the United States, including its territories and possessions, outside of U.S. Military Exchange and
outside of Canada. This warranty does not cover products purchased from a party that is not an authorized retailer, dealer
or distributor of AQUAPRO products.
OTHER IMPORTANT TERMS
This warranty is not transferable and may not be assigned. This Warranty shall be governed and construed under laws of
the state of Michigan. The Warranty Period will not be extended by any replacement or repair performed under this Warranty.
THIS WARRANTY IS THE EXCLUSIVE WARRANTY AND REMEDY PROVIDED BY AQUAPRO. ALL OTHER
WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OR MERCHANTABILITY OR FITNESS FOR
PARTICULAR PURPOSE, ARE DISCLAIMED. IN NO EVENT WILL AQUAPRO BE LIABLE FOR ANY SPECIAL,
INDRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND OR NATURE TO OWNER OR ANY PARTY
CLAIMING THROUGH OWNER WHETHER BASED IN CONTRACT, NEGLIGENCE, TORT, OR STRICT PRODUCTS
LIABLITY OR ARISING FROM ANY CAUSE WHATSOEVER. Some states do not allow for the exclusion of consequential
damages, so the above exclusion may not apply to you. This warranty gives you specific rights. You may also have others
that vary from state to state.
Thank you for choosing an AQUAPRO product!

NOTICE D’UTILISATION
POMPE ÀJET CONVERTIBLE AVEC RÉSERVOIR
DE 6 GALLONS US
Questions, problèmes, pièces manquantes? Avant de retourner au magasin, appelez le
Service àla clientèle AQUAPRO
du lundi au vendredi, de 8 h à18 h, heure normale de l’Est
1-844-242-2475
Modèle 63043

2 Pour une assistance technique professionnelle appelez 1-844-242-2475
PERFORMANCE
Modèle
HP
Débit d’eau en gal/h selon une pression totale de refoulement de
40 lb/po2
Arrêt de
pression
maximale
5’
10’
20’
30’
40’
50’
60’
70’
63043
1/2
450
396
330
300
282
228
210
132
66 lb/po2
Consignes de sécurité
1. Ne pas pomper de liquides explosifs ou inflammables tels que de l’huile, de l’essence, du kérosène, de l’éthanol, etc.
Ne pas utiliser en présence de vapeurs inflammables ou explosives. Le fait d’utiliser cette pompe avec ou à proximité
de liquides inflammables est susceptible de provoquer une explosion ou un incendie, d’où un risque d’accident corporel
et/ou de décès.
2. TOUJOURS débrancher l’alimentation de la pompe avant toute intervention.
3. Ne pas toucher le boîtier d’un moteur en marche. Le moteur est conçu pour fonctionner à des températures élevées.
De plus, ne pas démonter le boîtier du moteur.
4. Ne pas manipuler la pompe ni le moteur de la pompe avec des mains humides ou en se tenant dans l’eau ou sur une
surface humide ou moite.
5. Porter des lunettes de protection lors de tous travaux avec des pompes.
6. Ceci est une pompe double tension 115/230 V. VOLTAGE SELECTOR INSIDE PRESET 230 V.Pour la sélection 115 V,
se il vous plaît ouvrez le couvercle et réglez le commutateur sur la tension appropriée. Tout le câblage doit être effectué
par un électricien qualifié.
7. Protéger le cordon électrique des objets tranchants, des surfaces chaudes, des huiles et des produits chimiques. éviter
d’entortiller le cordon. Ne pas utiliser de cordons endommagés ou usés.
8. Vérifier que l’alimentation électrique correspond bien aux spécifications de la pompe.
9. Tout manquement à respecter cette notice et l’utilisation prévue de cette unité est susceptible d’invalider la garantie.
Toute tentative pour utiliser une pompe endommagée risque d’entraîner un dommage matériel, un accident corporel
grave, et/ou un risque de décès.
10. La pompe doit être connectée àun disjoncteur de fuite de terre de 230 V/115 V protégépar un fusible ou un disjoncteur
de 10 A (230 V) / 20 A (115 V).
11. Connaître les applications, limitations et dangers éventuels de la pompe.
12. Fixer la pompe sur une base solide.
13. Inspecter périodiquement la pompe et les composants du système afin de vérifier que les amenées de la pompe sont
dépourvues de boue, de sable et de débris. avant de procéder à une inspection, débrancher la pompe de l’alimentation
électrique.
14. Respecter l’ensemble de la réglementation électrique et de sécurité locale, ainsi que le Code national de l’électricité. Il
est en outre impératif de respecter l’ensemble des directives de l’administration américaine en charge de l’hygiène et
de la sécuritédu travail .
15. Le moteur de cette pompe est équipé d’un protecteur thermique qui se déclenche si la température du moteur devient
trop élevée. Ce protecteur se réenclenche une fois le moteur refroidi et une température acceptable atteinte. La pompe
peut redémarrer de manière inattendue si elle est branchée .