Aquaglide HATCHWAY 10 User manual

www.aquaglide.com
1
HATCHWAY 10
Owner’s Manual
www.aquaglide.com
version 1.0 - 8.22.2023

www.aquaglide.com
2
Capacity: 2 People
Dimensions:
L- 10.0 ft (3,05 m)
W- 6.5 ft (1,98 m)
H- 5.3 ft (1,60 m)
Minimum Water Depth: 5.6 ft (1,70 m)
Included:
1x Hatchway 10
1x Storage Wrap
1x Repair Kit
Language Translations:
English - pg. 2
Español - pg. 15
Français - pg. 28
Deutsch - pg. 41
HATCHWAY 10

www.aquaglide.com
3
WARNINGS
Use of this product and participation in the sport involves INHERENT RISKS of SERIOUS
INJURY or DEATH. User ASSUMES ALL RISK of injury or death.
• ALWAYS wear a properly tted USCG type III / Level 70N, ISO/CE or other agency approved
Life Jacket or Personal Flotation Device (PFD) as required in area of use.
• NEVER use while under the inuence of alcohol or drugs.
• NEVER leave children unattended. ONLY use under competent adult supervision.
• Not intended for use by children under 5 years of age.
• NEVER place wrists or feet through handles.
• NEVER use in water less than the specied minimum depth for this product.
• NEVER use with less than the specied minimum safe distance away of watercraft, shore,
docks, pilings, or other obstacles.
• NEVER swim under this product.
• NEVER dive from this product.
• NEVER exceed the manufacturer’s recommended number of users for this product.
• NEVER add any hardware or other attachments not otherwise supplied by the manufacturer.
• This product is not a personal otation device.
• ALWAYS read User’s Manual before use.
CAUTIONS
This user’s Manual is intended to alert you to some of the potentially dangerous conditions that
can arise in the use of this product. Other, unforeseen risks may exist, so always use caution
and common sense. Please contact the dealer or manufacturer of this product if you have any
questions about proper assembly, operation, or safe use of this product.
• Always read this user’s manual carefully before use and follow the instructions.
• Always limit use to swimmers only. This item provides no protection against drowning.
• Always be aware of potential dangers in the surrounding environment.
• Always take all reasonable precautions in using this product and instruct all users about safe
guidelines prior to use.
• Always maintain at least the specied minimum safe distance away from pool edge, boats,
docks, or other hard obstructions.
• Always maintain adequate vertical clearance above this item, particularly when used in indoor
pools.
WARNINGS & CAUTIONS
STOP! READ THIS OWNER’S MANUAL CAREFULLY
BEFORE USING THIS PRODUCT!
It is the owner’s responsibility to read the user’s manual and instruct all users in the safe operation of
these products. This Owner’s Manual is intended to alert you to some of the potentially dangerous
conditions that can arise in the use of this product.

www.aquaglide.com
4
• Always inate each air chamber to the specied working pressure before use. Under-ination
can cause injury due to instability.
• Always ensure connections are tight and that there is no gap between items.
• Regularly check mooring lines and connecting straps. Always replace any portion showing
signs of wear.
• Never use without proper anchoring and adequate minimum water depth for this product.
• Never exceed the maximum weight or user capacity stated for this product.
• Always evenly distribute weight from users or gear to prevent possible capsize.
• Never attempt somersaults while using this item. Head and/ or neck injuries can cause serious
injury, paralysis, or death.
• Never follow other climbers – an accidental fall may cause collision.
• Never follow others immediately into the water – wait until water is clear.
• Always remove personal items such as rings, watches or other sharp objects before use.
• Never use at night, in low-light, or in other adverse conditions.
• Never use in recreational pools. Supervised use in public or commercial pools is acceptable.
• Always secure the product when not in use to prevent access by any other users.
• Always ensure correct anchoring of the product prior to use.
• Always lubricate products with continual water ow or other suitable methods to limit risk of
skin burns. Be aware that friction may cause skin burns when attempting to slide.
AQUAPARK DISCLAIMER
The safety of our customers and their guests is our highest priority. Careful thought goes into the
design of our aquapark components, connection points and congurations to assure maximum
safety and enjoyment. Consequently, Aquaglide Lakefront and Aquapark products are not
authorized for use in combination with products or attachments from any other manufacturer.
Aquaglide product combinations must be authorized or approved in advance by the manufacturer.
Use of Aquaglide products in combination with products from any other manufacturer and/
or product arrangements not previously approved by Aquaglide may result in increased risk of
entrapment, injury, or death.
SALTWATER WARNING
Prolonged exposure to salt water can damage and/or shorten the expected lifetime of this product.
The marine environment includes many damaging elements including corrosion, abrasion, and
damage from marine life such as barnacles. Regular cleaning and rinsing with fresh water can
reduce these risks. A PVC-safe anti-fouling paint should be used to help protect this product
against marine growth. Damage caused by exposure to salt water is not covered by warranty.

www.aquaglide.com
5
Compliant with ISO 25649: 2017 -1, -2, -6, Class D
REACH, ASTM F/24
100%
122cm
213cm
max.
1,70m (5.6ft)
3,0m
(10ft)
181 kg
(400 lbs)
2 2
HATCHWAY 10

www.aquaglide.com
6
Inatable Products – Aquaglide makes some of the highest quality inatable products in the world.
With proper care and maintenance, our products are expected to last for years under normal use. We list
important tips and instructions below. If unsure about any point, please reach us through our website at
Aquaglide.com/contact-us.
Note: see Anchoring instructions (below) before inating this item. Strong winds can make it difcult to
control this product. Be aware of weather conditions before installation.
Air Pump - Use an air pump recommended for inating your product. For products this size, use of
a high-volume electrical pump is best. Air pressure requirements are low – 5.0psi (0,35bar) or less. Air
compressors designed for high-pressure ination are not recommended because they can easily lead to
over-ination.
Valve(s) – This product uses Halkey Roberts – type (HR) valves. Valve attaches to
product using a threaded backing plate making it easily replaceable in the unlikely
event of damage.
Access valve using a coin or at tool to twist the tamper-resistant cap counter-clock-
wise. To close, insert the cap and twist clockwise using the same
tool. Note: cap is the secondary air seal. See A.
To inate, an air pump with Halkey Roberts – type (HR) valve tting is
required. Insert tting into valve and twist clockwise to lock in place.
See B.
Valve Operation: To operate Halkey Roberts – type (HR) valve,
press plunger and turn 90 degrees to set valve for inate and product
use (plunger out = 1-way airow). Press plunger and turn 90 degrees
to deate (plunger in = 2-way airow). Note: valve is primary air seal.
After ination, close with cap for secondary seal. See C.
Pressure Release Valve: Product is tted with a pressure release valve (PRV) in
critical chamber(s) to help provide catastrophic protection against damage caused
by over-ination. It is still necessary to check and regulate air pressure to maintain
proper working pressure levels. PRV has a unique setting specied to release above,
and to close near working pressure. PRV attaches to product using a threaded
backing plate, making it easily serviceable. See D.
Proper Working Pressure for each chamber is listed below. Do not overll or underll. Excessive pressure
can cause damage to the product and may void the warranty. Do not use without adequate air pressure.
Product can become unstable if underlled and may not support indicated capacity. Use a pressure gauge
(manometer) to carefully monitor air pressure in the product especially during hot or cool periods.
A
Inate (1-way) Deate (2-way)
C
B
D
ASSEMBLY

www.aquaglide.com
7
Chart 1 – Working Pressure by Chamber - HATCHWAY 10
1. Locate a at, dry area with access to outlet for electrical pump. The best setup position will also make
launching easy. Never drag product as damage may occur.
2. Unfold product completely and locate Main Valve [1]. To help future storage, closely note original folding &
packaging method. Remove valve cap and conrm valve is in inate (1-way airow) position.
3. Insert air pump hose with proper valve tting into Main Valve [1], lock into place. Use pump to inate Main
Valve [1] to Working Pressure as shown in Chart 1.
4. Conrm that suitable anchor(s) and mooring lines are in place before launching this item (see Anchoring).
5. To launch product, lift completely and place in water. Large items may require many extra people to
accomplish this. Never drag product as damage may occur.
6. When connecting multiple items together, always follow manufacturer’s recommendations. Use only
Aquaglide Two-Step Vario-lock cinch straps and connecting rings. Make sure connection is tight and there is
NO GAP between items. Failure to connect items properly may result in injury or death. See E1 - E6.
a. Attach straps to ‘Boarding Features’ (example: Swimstep, Splashmat, Speedway, Breezeway or Deck)
where a connection is required. Boarding Features should not be attached to other Boarding Features.
b. Use all available rings to make connection. Standard connections use 5 rings. Some items use 3 or
occasionally 7 rings/ straps. HATCHWAY 10 is a Track Feature item with 5-ring connections on all 4 sides.
c. Float ‘Boarding Feature’ into desired position. Note: a matching set of connecting rings is required on
feature item.
d. Attach center strap to center ring on feature item. Connect loosely, then work outward until all straps are
connected.
e. Dive beneath to tighten all straps securely. Dive mask and several attempts may be required.
Valve [Inate Order] Working Pressure in psi (Bar)
MAIN [1] 1.2psi (0,083 bar)
E-1
E-4 E-5 E-6
E-2 E-3
Connecting Strap instructions

www.aquaglide.com
8
Proper anchoring is essential to the safety and performance of this product. We recommend using Aquaglide
mooring lines and weight recommendations as a starting point. Weight recommendations are intended to
keep products in place during a normal range of weather conditions faced by most aquaparks. Even in so-
called light-wind areas, storms, squalls and other extreme weather events can happen quickly. If improperly
anchored, product can move and/or oat away. Aquaglide is not responsible for damage, injury or loss due to
improper anchoring.
Open Water: (General guidelines - not intended to replace need for professional installation)
1. Place product in an area protected from wind and boat trafc. Conrm allowances for stated minimum
water depth, safe distance away from hard objects and vertical clearance requirements.
2. Consider prevailing conditions such as wind, waves and other environmental factors in positioning this
item. Inatable items can be unstable in strong winds. Slide faces are best positioned toward a breeze, not
across it. Check water and seabed for sharp or dangerous objects.
3. Keep product a safe distance from docks, boats, boat lifts, and any other structures. To prevent potential
damage to product, injury or death, NEVER tie the product to a dock.
4. Use one vertical mooring line for each anchor ring with an appropriate weight anchor, ground screw, or
earth anchor at base. For exposed anchorages or water depth greater than 20ft. (6m), bridles connecting two
rings to one mooring line may be preferable.
5. Anchor weight recommendations are based on the maximum potential wind loads generated by each
item at a wind speed of 26 knots (48 km/h, 30 mph). Weight recommendations are based on the apparent
weight of concrete mooring blocks in either salt or fresh water. If signicantly stronger winds are forecast, we
recommend partially deating larger items or removing items from the water for storage.Sites with potential
for extreme weather, strong tides, currents, winds and/ or swell should consider using up to 50% additional
weight or holding power.
6. Install anchors and mooring lines before inating this product.
Commercial Pool:
1. Product placement in commercial pool should be checked carefully in advance to conrm allowances for
the stated minimum water depth, safe distance away from hard objects (pool edge) and vertical clearance
requirements. Most residential pools cannot meet these requirements.
2. Pool moorings typically use a minimum of 4 horizontal mooring lines made from heavy duty elastic. Addi-
tional horizontal moorings should be added to increase stability and as necessary for larger product groups.
3. Horizontal Moorings are usually attached to pool anchor eyes, such as those used to secure lane buoy
lines. Adjust mooring lines to keep product(s) under tension at all times.
ANCHORINGANCHORING
Anchor Details – Hatchway 10 Qty/ Weight lb (kg)
Anchor rings on product 4
Recommended anchor qty 4
2-Way Bridle? No
Recommended weight/ anchor 250lb (100kg)
Recommended total anchor weight 1000lb (400kg)

www.aquaglide.com
9
Hatchway 10 is a oating activity for use in water. Users traverse the item by climbing over, around or through
the circular hatchway obstacle. Users may slide onto or off of the item after making sure the area is clear of
other users.
Never gather beneath obstacle wall while someone is climbing. Always make sure area is clear before jumping
or sliding.
PVC surfaces are more slippery when wet, which can lead to loss of balance when walking or climbing. Slid-
ing surfaces will work best when wetted rst. Chemical treatments are available to reduce friction on sliding
surfaces, but are generally not necessary if products are kept clean.
Maintain working pressure: Air pressure depends on temperature. Always conrm proper working pres-
sure before and during use, as temperature changes may affect internal pressure. If the product shows signs
of instability or loss of pressure, discontinue use until the product returns to working pressure and/or repairs
are made.
Spread loads: Do not concentrate more than 300 lbs (136 kg) in one area during use.
Manage Winds/Thunderstorms: If strong winds (25 knots+) or thunderstorms are forecast, discontinue
use. Remove the product from the water and secure or store it.
Check connections: Check regularly to conrm that all connections are secure. Replace connecting straps
that show signs of wear.
Clean and maintain: Check regularly that the product is clean and that all handles and accessories work
properly. Each site requires its own cleaning/maintenance schedule, but regular cleaning and periodic main-
tenance is necessary to ensure the full life of the product. Replace handles or accessories that show signs of
wear.
Check moorings: Regularly check mooring lines and anchors, especially after extreme conditions. Replace
any item showing signs of permanent wear or stretching.
OPERATION

www.aquaglide.com
10
Proper cleaning, maintenance, and storage is essential to help prolong the life of your product. Do not use
petroleum-based cleaners on this product. Improper use of a pressure washer can damage or destroy the
product.
Basic Cleaning: Use soft bristly brush or sponge with mild soap and fresh water.
Difcult Cleaning: For heavy stains, marine growth, algae, mold, dirt and oils check with your distributor, or
on our website, Aquaglide.com for commercial-grade cleaning solutions. In general, be sure that any cleaning
products are clearly labeled as safe for PVC.
UV Protectant: Long-term exposure to sunlight will reduce product life and can damage the product.
Regularly apply a UV protectant to exposed surfaces to ensure the life of your product. The best time to begin
applying UV protectant is when the item is clean and new. Repeat applications depend on site specics. In
temperate climates, apply 1-2 times per year. In tropical climates, monthly application is not uncommon. Find
more information on professional-grade UV protectants from your distributor, or at Aquaglide.com.
Replacement parts: Items like valves, PRV’s, handles, rings and other accessories can occasionally wear
out and need replacement to maintain the full function of your product. Check with your distributor, or on our
website, Aquaglide.com for available parts and replacement instructions.
STORAGE - Clean, Protect, Dry: Clean product and consider applying UV protectant before storage. UV
protectant conditions the PVC material and will help protect against dirt accumulation during storage. Conrm
product is completely dry before folding.
Deate & Fold: Deate product completely: Consider using electric pump in ‘deate’ mode. Close valve to
prevent air return. Fold deated product in similar manner to original packaging. If uncertain, fold in thirds,
then roll loosely toward the valve(s). Enclose product in original storage wrap, if included.
Storage: Store the product out of direct sunlight and protect from environment in a clean, dry location such
as a sealed closet, crate or container to prevent against serious threat of rodent damage. When building or
sourcing storage container, use original box dimensions as a baseline. Size up by at least 15-20% to allow for
imperfect folding. Never store in a damp location or at temperatures below 40 F (4 C).
CARE AND MAINTENANCE

www.aquaglide.com
11
Despite the durability of this product, occasionally accidents happen. This product includes a
repair kit with some matching repair materials to help. If you should need additional repair materials
or advice, check with your distributor or on our website, Aquaglide.com for guidance. If you believe
your product has a manufacturing defect, please submit a warranty claim before making repairs.
This Product is made with Duratex fabric-reinforced PVC. Inate fully and swab with Windex or soapy water
and a sponge to locate leak.
Self-Adhesive TPU Patch Repair – Ideal for emergency repairs.
1. With leak located, cut supplied patch (or Tear-Aid, Type B) patch using sharp scissors. Round
corners (approximately ¼” radius). Patch should cover 1” (2.5cm) outside leak in all directions.
2. Use solvent such as MEK, Acetone or Alcohol to clean patch area. Dry completely.
3. Peel back paper backing to expose adhesive. Align patch and apply pressure. Peel back remaining
paper backing. Avoid trapping air bubbles. Rub rmly from center outward.
Fabric Reinforced PVC with Glue Repair – Ideal for Duratex & dropstitch repairs. Optional Adhe-
sive: HH-66, Aquaseal+FD.
1. With leak located, deate product. Arrange work surface so that repair is most accessible.
2. Cut matching PVC patch material using sharp scissors or razor knife. Round corners
(approximately ¼” radius). Patch should cover 1” (2.5cm) outside leak in all directions.
3. Use solvent such as MEK, Acetone or Alcohol to clean patch area and back of patch. Dry
completely.
4. Use sandpaper to roughen patch area and back of patch.
5. Use solvent again to quickly remove sanding residue.
6. Dry t patch and use pencil to outline location.
7. Use a small disposable brush to apply a thin, even layer of glue to patch area. Glue evenly up to
pencil outline. Glue back of patch.
8. Allow glue to cure (30 - 60 seconds) – until surface glazes slightly.
9. Repeat 7-8 to add a second coat of glue in the same way.
10. Align patch using pencil outline as a guide. Once surfaces touch, bond will be immediate.
11. Apply patch, starting at one corner and working outward.
12. Rub rmly from center outward for 1 – 2 minutes.
13. Allow to cure for 2 hours, minimum. Cure 12 hours for full strength.
REPAIR INSTRUCTIONS

www.aquaglide.com
12
By assembling and/or using this product, you are agreeing to: (1) Read and understand the terms set forth
below and (2) to require anyone using this product to familiarize themselves with such terms.
ASSUMPTION OF RISK: Use of this product and any of its components involves certain inherent risks,
dangers, and hazards which can result in serious personal injury and death. In using the product, you freely
agree to assume, acknowledge, and accept any and all known and unknown risks of injury while using this
equipment. The risks inherent in the sport can be greatly reduced by abiding by the Warning Guidelines
listed in this Owner’s Manual and by using common sense.
ARBITRATION: In further consideration of the sale to you of this product and any of its components, you
hereby agree to submit to binding arbitration any and all claims which you believe you may have against
Aquaglide arising from the use of any Aquaglide equipment or products. The arbitration shall be pursuant
to the rules of the American Arbitration Association. Arbitration shall be commenced within (1) year from the
date on which any alleged claim rst arose. Further, the arbitration shall be held in Lynnwood, Washington
unless otherwise mutually agreed to by all parties. The arbitration award through the American Arbitration
Association may be enforced by any Court of competent jurisdiction.
ENTIRE AGREEMENT: In entering into this Agreement, you are not relying upon any oral or written
representations other than what is set forth in this agreement and the Aquaglide Owner’s Manual.
ACKNOWLEDGEMENT OF RISK AGREEMENT

www.aquaglide.com
13
At Aquaglide we pride ourselves on rst class customer service and brand integrity. We strive to
manufacture our products to the highest quality standards and we proudly stand behind them. Despite our
best efforts, occasionally a product may exhibit a manufacturing defect. If you believe your product has a
manufacturing defect, please submit a warranty claim and await response before making any repairs. Once
a warranty claim is submitted our staff will review your submission and deliver a prompt resolution.
It is always our primary intention to treat each customer fairly.
Commercial Products
Commercial products are those that are specically intended, designed, and sold for commercial purposes
including independent operators, camp, or municipal use (example, a city pool). Commercial products are
normally exposed to a greater number of users and higher level of use.
Warranty Coverage – Commercial Products
Product warranty covers all critical manufacturing defects including general workmanship, seam failures,
and material failure due to manufacturing defects.
Warranty Terms
The warranty term for commercial aquapark products is (3) three years from date of purchase.
Commercial products under an approved warranty claim may be repaired or replaced, in part or entirely, at
the sole discretion of Aquaglide. Commercial products in use for more than (2) years but less than (3) years
may also be pro-rated based on condition and use for credit at the sole discretion of Aquaglide. Normal
wear should be expected on consumptive parts such as straps, handles, ropes, footsteps and D-rings.
Such items are easily repairable and may or may not be replaced under warranty depending on the cause
of failure.
For consumers covered by specic protection laws and/ or regulations in country of purchase or residence,
the benets conferred by this Aquaglide Warranty are in addition to all rights and remedies conveyed by
such laws and regulations including, but not limited to, these additional rights.
What is NOT Covered Under Warranty?
• Normal wear and tear
• Freight damage (freight claim must be led to cover shipping damage)
• Damage while in storage (freeze or other damage)
• Repairable cuts, punctures, or tears due to external forces
• Damage caused by sharp object when opening boxed product
• Damage caused by dragging product
• Damage caused by exceeding the maximum weight and/ or user capacity
• UV Damage without proper treatment (material breakdown, fading)
• Damage, or failure due to over-ination including thermal over-ination from sun exposure
• Vandalism or intended damage
• Product failure due to force majeure, acts of God, or inclement weather
• Improper maintenance and/or cleaning
• Damage caused by animals or plants including marine growth
• Damage caused by chemicals or poor water quality
WARRANTY

www.aquaglide.com
14
Warranty Claim Requirements
1. Dated proof of purchase or original invoice, for original owner.
2. High resolution photo or video showing serial number (where relevant).
3. High resolution photo or video showing entire product.
4. High resolution photos or video of defective portion of product. If leaking, show leak with and without
soapy water.
Warranty Claim Submission
In the United States, warranty claims may be submitted by end consumer or retailer at
www.aquaglide.com/warranty/. Please gather the information in claim requirements and submit
warranty claim electronically.
Outside the United States please gather the information in claim requirements and submit warranty claim
through your dealer or national distributor.
Enter clear and complete information including your contact information. Once a claim is submitted our
team will make every effort to address it promptly.

www.aquaglide.com
15
Capacidad: 2 Personas
Dimensiones:
Longitud - 10,0 pies (3,05 m)
Ancho - 6,5 pies (1,98 m)
Altura - 5,3 pies (1,60 m)
Profundidad mínima del agua: 5,6 pies (1,70 m)
Incluido:
1x Hatchway 10
1 envoltura de almacenamiento.
1 kit de reparación.
ESPAÑOL
HATCHWAY 10

www.aquaglide.com
16
Es responsabilidad del propietario leer el manual del usuario e instruir a todos los usuarios sobre el funcionamiento
seguro de estos productos. Este manual del propietario está destinado a alertarle sobre algunas de las condiciones
potencialmente peligrosas que pueden surgir en el uso de este producto.
Advertencias El uso de este producto y la participación en el deporte implica RIESGOS INHERENTES de LESIONES
GRAVES o LA MUERTE. El usuario ASUME TODOS LOS RIESGOS de lesiones o muerte.
• SIEMPRE use un chaleco salvavidas o un dispositivo de otación personal (PFD) aprobado por la agencia USCG
tipo III / Nivel 70N, ISO / CE u otra agencia, según se requiera en el área de uso.
• NUNCA lo use bajo la inuencia de alcohol o drogas.
• NUNCA deje a los niños desatendidos. Úselo ÚNICAMENTE bajo la supervisión de un adulto competente. No está
diseñado para ser utilizado por niños menores de 5 años.
• NUNCA coloque muñecas o pies a través de las manijas.
• NUNCA lo use en agua a menos de [la profundidad mínima especicada para este producto {pies (metros)}] de
profundidad.
• NUNCA lo use dentro de [la distancia de seguridad mínima especicada de {pies (metros)} de embarcaciones,
costa, muelles, pilotes u otros obstáculos.
• NUNCA nade debajo de este producto.
• NUNCA bucee desde este producto.
• NUNCA exceda el número de usuarios recomendado por el fabricante para este producto.
• NUNCA agregue ningún hardware u otros accesorios que no hayan sido suministrados por el fabricante.
• Este producto no es un dispositivo de otación personal.
• SIEMPRE lea el manual del usuario antes de usarlo.
Precaución El objetivo de este manual del usuario es alertarle sobre algunas de las condiciones potencialmente
peligrosas que pueden surgir en el uso de este producto. Pueden existir otros riesgos imprevistos, así que siempre
tenga cuidado y use el sentido común. Póngase en contacto con el distribuidor o el fabricante de este producto si tiene
alguna pregunta sobre el montaje, funcionamiento o uso seguro de este producto.
• Lea siempre este manual de usuario con atención antes de usarlo y siga las instrucciones.
• Limite siempre el uso a nadadores. Este artículo no ofrece protección contra el ahogamiento.
• Sea siempre consciente de los peligros potenciales en el entorno circundante.
• Siempre tome todas las precauciones razonables al usar este producto e instruya a todos los usuarios sobre las
pautas de seguridad antes de su uso.
• Siempre mantenga al menos la distancia mínima de seguridad especicada lejos del borde de la piscina, botes,
muelles u otras obstrucciones difíciles.
• Mantenga siempre un espacio libre vertical adecuado por encima de este elemento, especialmente cuando se use
en piscinas cubiertas.
• Siempre ine cada cámara de aire a la presión de trabajo especicada antes de su uso. El inado insuciente
puede causar lesiones debido a la inestabilidad.
• Asegúrese siempre de que las conexiones estén rmes y que no haya espacios entre los elementos.
• Compruebe periódicamente las líneas de amarre y las correas de conexión. Reemplace siempre cualquier parte
que muestre signos de desgaste.
• Nunca lo use sin un anclaje adecuado y una profundidad de agua mínima adecuada para este producto.
• Nunca exceda el peso máximo o la capacidad de usuario indicada para este producto.
ADVERTENCIAS Y PRECAUCIONES
Es responsabilidad del propietario leer el manual del usuario e instruir a todos los usuarios sobre
el funcionamiento seguro de estos productos. Este manual del propietario está destinado a
alertarle sobre algunas de las condiciones potencialmente peligrosas que pueden surgir en el uso
de este producto.

www.aquaglide.com
17
• Distribuya siempre uniformemente el peso de los usuarios o del equipo para evitar un posible vuelco.
• Nunca intente saltos mortales mientras usa este artículo. Las lesiones de cabeza y / o cuello pueden causar
lesiones graves, parálisis o la muerte.
• No siga nunca a otros escaladores: una caída accidental puede provocar una colisión.
• Nunca siga a otros inmediatamente al agua; espere hasta que el agua esté limpia.
• Siempre quítese los artículos personales como anillos, relojes u otros objetos punzantes antes de usarlos.
• Nunca lo use de noche, con poca luz o en otras condiciones adversas.
• Nunca lo use en piscinas recreativas. Se acepta el uso supervisado en piscinas públicas o comerciales.
• Asegure siempre el producto cuando no esté en uso para evitar el acceso de otros usuarios.
• Asegúrese siempre de un correcto anclaje del producto antes de su uso.
• Lubrique siempre los productos con un ujo continuo de agua u otros métodos adecuados para limitar el riesgo de
quemaduras en la piel. Tenga en cuenta que la fricción puede causar quemaduras en la piel al intentar deslizarse.
DESCARGO DE RESPONSABILIDAD DE AQUAPARK La seguridad de nuestros clientes y sus invitados es nuestra
máxima prioridad. Se piensa cuidadosamente en el diseño de nuestros componentes, puntos de conexión y congura-
ciones del parque acuático para garantizar la máxima seguridad y disfrute. En consecuencia, los productos Aquaglide
Lakefront y Aquapark no están autorizados para su uso en combinación con productos o accesorios de cualquier otro
fabricante. Las combinaciones de productos Aquaglide deben ser autorizadas o aprobadas previamente por el fab-
ricante. El uso de productos Aquaglide en combinación con productos de cualquier otro fabricante y / o arreglos de
productos no aprobados previamente por Aquaglide puede resultar en un mayor riesgo de atrapamiento, lesiones o
muerte.
Advertencia de agua salada - La exposición prolongada al agua salada puede dañar y / o acortar la vida útil espera-
da de este producto. El entorno marino incluye muchos elementos dañinos, como la corrosión, la abrasión y los daños
causados por la vida marina, como los percebes. La limpieza y el enjuague regulares con agua dulce pueden reducir
estos riesgos. Se debe usar una pintura antiincrustante segura para PVC para ayudar a proteger este producto contra
el crecimiento marino. Los daños causados por la exposición al agua salada no están cubiertos por la garantía.

www.aquaglide.com
18
Conforme con ISO 25649: 2017 -1, -2, -6, Clase D
REACH, ASTM F/24
100%
122cm
213cm
max.
1,70m (5.6ft)
3,0 m
(10 ft)
181 kg
(400 lbs)
2 2
HATCHWAY 10

www.aquaglide.com
19
Productos inables: Aquaglide fabrica algunos de los productos inables de mayor calidad del mundo. Con el cuida-
do y mantenimiento adecuados, se espera que nuestros productos duren años con un uso normal. A continuación,
enumeramos consejos e instrucciones importantes. Si no está seguro de algún punto, comuníquese con nosotros a
través de nuestro sitio web en Aquaglide.com/contact-us.
Nota: consulte las instrucciones de anclaje (a continuación) antes de inar este artículo. Los vientos fuertes pueden
dicultar el control de este producto. Tenga en cuenta las condiciones climáticas antes de la instalación.
Bomba de aire: use una bomba de aire recomendada para inar su producto. Para productos de este tamaño, es
mejor utilizar una bomba eléctrica de gran volumen. Los requisitos de presión de aire son bajos: 5,0 psi (0,35 bar) o
menos. No se recomiendan los compresores de aire diseñados para inado a alta presión porque pueden provocar
fácilmente un inado excesivo.
Válvula (s): este producto utiliza válvulas de tipo Halkey Roberts (HR). La válvula se conecta al
producto mediante una placa de respaldo roscada, lo que la hace fácilmente reemplazable en
el improbable caso de daño.
Acceda a la válvula con una moneda o una herramienta plana para girar la tapa a prueba de
manipulaciones en sentido antihorario. Para cerrar, inserte la tapa y gírela en sentido horario
con la misma herramienta. Nota: la tapa es el sello de aire secundario. Ver A.
Para inar, se requiere una bomba de aire con conexión de válvula de tipo
Halkey Roberts (HR). Inserte el accesorio en la válvula y gírelo en sentido
horario para bloquearlo en su lugar. Ver B.
Operación de la válvula: Para operar la válvula tipo Halkey Roberts (HR),
presione el émbolo y gírelo 90 grados para congurar la válvula para inar
y usar el producto (émbolo hacia afuera = ujo de aire de 1 vía). Presione el
émbolo y gírelo 90 grados para desinar (émbolo hacia adentro = ujo de aire
de 2 vías). Nota: la válvula es un sello de aire primario. Después del inado,
cierre con la tapa para el sello secundario. Ver C.
Válvula de liberación de presión: el producto está equipado con una vál-
vula de liberación de presión (PRV) en la(s) cámara(s) crítica(s) para ayudar a
brindar protección contra daños catastrócos causados por un inado exce-
sivo. Todavía es necesario vericar y regular la presión de aire para mantener
los niveles de presión de trabajo adecuados. PRV tiene una conguración única especicada
para liberar arriba y para cerrar cerca de la presión de trabajo. PRV se adhiere al producto
mediante una placa trasera roscada, lo que facilita su mantenimiento. Semilla.
La presión de trabajo adecuada para cada cámara se enumera a continuación. No sobrellene
ni subllene. Una presión excesiva puede dañar el producto y anular la garantía. No lo use sin la
presión de aire adecuada. El producto puede volverse inestable si no se llena correctamente y
es posible que no admita la capacidad indicada. Use un indicador de presión (manómetro) para
monitorear cuidadosamente la presión de aire en el producto, especialmente durante los períodos cálidos o fríos.
A
Inar (1 vía) Desinar (2-vias)
C
B
D
EMONTAJE

www.aquaglide.com
20
Cuadro 1 - Presión de trabajo por cámara - HATCHWAY 10
1. Ubique un área plana y seca con acceso al tomacorriente para la bomba eléctrica. La mejor posición de conguración
también facilitará el lanzamiento. Nunca arrastre el producto ya que puede dañarlo.
2. Desdoble el producto por completo y localice la válvula principal [1]. Para facilitar el almacenamiento futuro, tenga en cuen-
ta el método original de plegado y embalaje. Retire la tapa de la válvula y conrme que la válvula está en la posición de inado
(ujo de aire de 1 vía).
3. Inserte la manguera de la bomba de aire con el ajuste de válvula adecuado en la válvula principal [1] y asegúrela en su
lugar. Utilice la bomba para inar la válvula principal [1] a la presión de trabajo, como se muestra en el Cuadro 1.
4. Conrme que las anclas y las líneas de amarre adecuadas estén en su lugar antes de botar este elemento (ver Anclaje).
5. Para lanzar el producto, levántelo completamente y colóquelo en agua. Los artículos grandes pueden requerir muchas
personas adicionales para lograr esto. Nunca arrastre el producto ya que puede dañarlo.
6. Cuando conecte varios elementos, siga siempre las recomendaciones del fabricante. Utilice únicamente correas de cincha
y anillos de conexión Aquaglide Two-Step Vario-lock. Asegúrese de que la conexión sea rme y que NO HAYA ESPACIO
entre los artículos. Si no se conectan correctamente los elementos, se pueden producir lesiones o la muerte. Ver E1 - E6.
A. Fije las correas a las “Características de abordaje” (ejemplo: Swimstep, Splashmat, Speedway, Breezeway o Deck)
donde se requiera una conexión. Las funciones de embarque no deben adjuntarse a otras funciones de embarque.
B. Utilice todos los anillos disponibles para realizar la conexión. Las conexiones estándar utilizan 5 anillos. Algunos artículos
usan 3 u ocasionalmente 7 anillos/correas. HATCHWAY 10 es un elemento Track Feature con conexiones de 5 anillos en
los 4 lados.
C. Haga otar la ‘Función de abordaje’ en la posición deseada. Nota: se requiere un juego de anillos de conexión a juego
en el artículo de características.
D. Fije la correa central al anillo central en el artículo destacado. Conecte sin apretar, luego trabaje hacia afuera hasta que
todas las correas estén conectadas.
mi. Sumérgete debajo para apretar todas las correas de forma segura. Es posible que se requieran máscaras de buceo y
varios intentos.
E-1
E-4 E-5 E-6
E-2 E-3
Instrucciones de la correa de conexión
Válvula [Orden de Inado] Presión de trabajo en psi (bar)
MAIN [1] 1.2psi (0,83 bar)