Aquaport DELUXE AQP-WCM User manual

DELUXE COLLECTION
Executive Water Cooler
Cold and Room
AQP-WCM

Register your warranty on line at www.aquaport/warranty
By registering your warranty on line you will be automatically entered into our monthly prize draw.
CUSTOMER HOTLINE: [phone]
Register your warranty online at www.aquaport/warranty
Aquaport Corporation Pty Ltd
PO Box 81 Findon SA 5023 Australia
Telephone: [phone]
Facsimile: 08 8354 0722
Email: [e-mail]
Web: www.aquaport.com.au
Congratulations on your purchase
of an Aquaport water cooler unit
Thank you for purchasing the Aquaport Executive water cooler.
This unit is easy to install and can be used with any 11-19lt spring water bottle and most filter bottles.
Note: Please read through the instructions carefully before using or installing the product and ensure that the
manual is kept in a safe place for future reference.
The system must be properly installed and located in accordance with the installation instructions before it is used.
Electrical Requirements:
Australia / New Zealand 240V / 230V 50Hz
Rated Current: 0.8A
Consumption: 85W
Capacity: ≤10°C 2L/H
Climatic Class: T
N 23934

INSTALLATION AND OPERATING INSTRUCTIONS 1
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always
be followed.
• Read all instructions carefully.
• Ventilation – The air vents must not be obstructed at any time, air flow is
required for unit to operate effectively.
• This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for
their safety.
Children should be supervised to ensure that they do not play with the
appliance
• To protect against fire, electric shock and personal injury, do not
immerse cord, plugs, or appliance in water or other liquid.
• Unplug from outlet when not in use and before cleaning.
• Do not operate any appliance with a damaged cord or plug or after the
appliance malfunctions, or has been damaged in any manner.
• Return appliance to the nearest authorized service facility for
examination, repair or adjustment.
• The use of accessory attachments not recommended by the appliance
manufacturer may result in fire, electric shock or personal injury.
• Do not use outdoors.
• Do not let cord hang over edge of table or counter, or touch hot
surfaces.
• Do not place on or near a hot gas or electric burner, or in a heated oven.
• Do not use appliance for other than intended use.
• This appliance should always be used in conjunction with a safety
switch.
• Place unit in a flat well-ventilated location at least 100mm from wall or
other Appliances.
• Ensure unit is properly grounded.
• A power outlet is required to operate the water cooler.
For best performance, do not place the unit near an oven, heater, direct
sunlight or any other heat source.

2INSTALLATION AND OPERATING INSTRUCTIONS
SPECIAL PRODUCT INSTRUCTIONS
This appliance is designed for either household or personal use.
Each model is designed to supply a certain maximum number of
servings per hour. Please consult with your sales representative or
our Website for the proper Aquaport unit for your specific needs.
Any servicing other than cleaning and user maintenance will violate
the terms of this WARRANTY.
CAUTIONS:
• Do not immerse base in water or try to disassemble.
• Do not lay unit on its side, always keep upright.
• If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.
• Check voltage to be sure that the voltage indicated on the
nameplate agrees with your voltage.
• Never clean with scouring powders or abrasives.
• Keep the product away from direct sunlight.
• A power outlet is required to operate the water cooler.

INSTALLATION AND OPERATING INSTRUCTIONS 3
A. Bottle support and spike
B. Cold Tap
C. Room Tap
D. Drip Tray
E. Bottle Support and Spike
F. Carry Handle
G. ID Plate & Serial Number
H. Fuse Holder
I. Power Switch
J. Thermostat
A
B
C
D
E
F
G
H
I
J
Parts Identification Diagram

4INSTALLATION AND OPERATING INSTRUCTIONS
A. Executive Water Cooler Installation for Spring Water bottles.
Please follow the instructions below if you are using a spring
water bottle.
Do not turn on the water cooler until the following instruction
have been followed.
1. Ver tically insert a spring water bottle into the bottle
supporter on top of the water cooler, the spike will pierce the
bottle cap. You will see bubbles appear inside the bottle, wait
until the bubbling has stopped before dispensing water form
both taps
Note: If you are applying a spring water bottle to the water
cooler for the first time and you do not see any bubbles appear
inside the bottle, open both taps until the bubbling starts and
water flows from both taps. Refer to the trouble shooting guide
for more information.
2. Once the bubbling has stopped, drain 1-2lts of water from
both taps.
Note: The water cooler has been flushed before it left the factory
however we strongly recommend 2-3lts of water is flushed
through the unit before using.
3. Insert the power plug into the wall socket, and turn the green
power switch ON. The power switch is situated at the rear of
the unit.
4. At the front of the unit there are 3 indicator lights, the
red LED on the right is the power light and will continually
illuminate while the unit is turned on. The Green LED cooling
light on the left will illuminate when the compressor is
running and cooling the water. When cooling is finished the
Green cooling LED light will turn off and the middle Yellow
Auxiliary LED light will illuminate until cooling is required
again.
5. When the unit is turned on for the first time, allow the unit to
cool the water for 1-2 hours before dispensing cold water.
B. Executive Water Cooler Installation for Filter bottle.
Please follow the instructions below if you are using a filter
bottle.
Do not turn on the water cooler until the following instruction
have been followed.
1. Remove the bottle support and spike from the water cooler.
See figure 1 on page 5.

INSTALLATION AND OPERATING INSTRUCTIONS 5
2. To remove the bottle supporter there is an arrow and the
word “OPEN” embossed into the bottle support. Line this up
with the small sticker found on the top panel of the water
cooler that also has an arrow the word “OPEN”. Then grab
the bottle supporter by placing your fingers under the rim and
vertically pull off.
3. When the bottle support is removed you should be able to
see inside the stainless steel cooling tank.
4. Follow the instructions that come with the filter bottle for
correct installation.
5. Place the filter bottle on top of the water cooler and fill as per
the instruction in the filter bottle user manual.
Note: Filter bottles generally have a
slower flow rate compared to spring
water bottles, hence it will take longer
to fill the cooling tank. Allow the
cold tank to fill for 30 minutes before
following Steps 2-5 as explained in
section A) Executive water cooler
Installation for Spring Water bottles.
C. Product Use
Always closely supervise children around this appliance.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.
The Aquaport Executive water cooler has been rated to provide
a limited number of servings per hour. On average you should be
able to receive 2-4L of cold water within 1hour. Higher ambient
temperature will affect its per formance.
The thermostat has been set by the manufacturer and does not
need to be adjusted. Do not adjust the thermostat unless advised
by Aquaport. Unauthorised adjustment or modification to the unit
will void the warranty.
Do not hesitate to contact our Customer Care Service line on
1300 764 325 or aquaport@aquapor t.com.au
Fig 1

6INSTALLATION AND OPERATING INSTRUCTIONS
D. Executive Water Cooler Not Used For Long Periods
If the Aquaport Executive water cooler will not been used for a
long period of time, turn the unit off from the rear power switch
and unplug from the wall socket. Remove the spring water or
filter bottle from the unit and drain all water from the taps. If
there is any water left inside the cooling tank, gently tip the
water cooler upside down to remove the water. DO NOT leave the
water cooler upside down for more then 20 seconds.
Fill the water cooler with fresh water as per the instructions on
page 4.
E. Sanitation:
We recommend that the water cooler be cleaned and sanitised
every 3-4 months. Contact Aquapor t should you wish to
purchase Sanitising Sachets on 1300 764 325.
WARNING: Before cleaning unit turn off power and unplug unit to
avoid electrical shock.
Hand wash all components:
• Remove bottle support and spike, twist anti-clockwise and lift.
• Pull out inner dividing plate (or baffle)
• Wash the stainless steel tank reservoir and rinse out. Drain all
water out through the taps. AVOID GETTING ANY WATER ON
THE UNIT.
• Use a soft damp cloth to wipe down the unit.
• Do not submerge the unit in water or spray with any harsh
cleaning substances.
• After cleaning the product, replace water bottle and ensure
water is running out of the taps before turning on the power
switch.
Do not hesitate to contact our Customer Care Service line on
1300 764 325 or aquaport@aquapor t.com.au

INSTALLATION AND OPERATING INSTRUCTIONS 7
F. Trouble Shooting
BEFORE YOU CALL FOR SERVICE PLEASE REVIEW THE TROUBLE SHOOTING TIPS FIRST.
Problem Possible Causes What To Do
No Power
1. Unit is not plugged into the wall socket.
2. Power switch at rear of unit is turned off.
3. Fuse has blown.
1. Check connection to wall socket.
2. Turn unit on from rear power switch.
3. Replace with new fuse.
Not Cooling
1. Unit is not plugged into the wall socket.
2. Power switch at rear of unit is turned off.
3. Unit may have been laid down during
transport.
1. Check connection to wall socket.
2. Turn unit on from rear power switch.
3. If the unit has been laid down during transport, keep the unit
up right for 48 hours before turning on. If still not cooling call
customer service on 1300 764 325.
Water is
leaking. *99%
of leaks that
may occur with
this unit are
caused by the
bottle used
with the water
cooler*
1. Pin hole in spring water bottle.
2. Faulty float valve on filter bottle.
3. Tap is not installed correctly.
4. Loose hose connection.
1. Pin hole leaks are common when using polycarbonate spring
water bottles. The bottle supporter of the Executive Water Cooler
is fitted with a non-spill valve which will stop the water cooler
leaking if a spring water bottle has a pin hole. However it is highly
recommended that the spring water bottle is replaced and the fault
reported to the spring water supplier.
2. Float valve on filter bottle is not shutting off, contact filter bottle
supplier for replacement float valve.
3. Ensure the tap in screwed onto the water cooler tightly.
4. Call customer service on 1300 764 325.

8INSTALLATION AND OPERATING INSTRUCTIONS
Problem Possible Causes What To Do
No Water Flow
From Faucet
1. Water bottle is empty.
2. Air block.
3. Unit is freezing.
4. Filters are blocked in the filter bottle.
1. Replace spring water bottle or re-fill filter bottle.
2. Open both taps until water dispenses from both taps. An air
block will only usually occur when the unit is brand new.
3. If the cold thermostat has been adjusted then this may cause
the unit to over cool and freeze. Reset back to factory setting. If
the thermostat has not been adjusted Call customer service on
1300 764 325.
4. Change filter cartridges in filter bottle or re-soak the filters to
loosen material inside according to the filter instructions.
Bad Taste From
Cooler
1. Filters are old.
2. Contaminated water supply.
3. Unit is brand new.
1. Change filters in filter bottle.
2. Check with spring water supplier to ensure water has not been
contaminated.
3. Flush water from the unit thoroughly for 10 minutes to alleviate
taste. If taste persists drain all water from unit and air for 24 hours
with the taps opened before re-filling with water. If the problem
persists call customer service on 1300 764 325.
Excessive Noise
From Unit
1. Improper installation.
2. Damaged during transport.
1. Turn off unit and ensure the unit is on a solid level sur face.
2. Call customer service on 1300 764 325.

INSTALLATION AND OPERATING INSTRUCTIONS 9
G. Your Aquaport 12 Month Replacement Warranty
Aquaport warrants this appliance to the first purchaser and
subject to the stated conditions:
Warranty warrants any defect in materials or workmanship in the
manufactured product, within the first twelve months from the
date of purchase will be repaired or the unit will be replaced at
our discretion.
Register online now for your chance to win monthly prizes at
www.aquapor t/warranty
Conditions Of This Warranty:
1. This product has been fully installed in accordance with the
user manual installation instructions.
2. The warranty extends only to repairing or replacing any
component that proves to be defective in material or
workmanship.
3. The warranty does not cover defects occasioned by misuse,
alterations, accidents, or used for other than the intended
purpose.
4. The warranty does not cover use of this product where water
is microbiologically unsafe or of unknown quality, without
adequate disinfection before or after the system.
5. The warranty does not cover damage to the product caused
by accident, fire, or floods.
6. Proof of purchase is required for warranty claims. Please
keep purchase receipt in a safe place.
To enable us to register your warranty and provide service should
a problem occur, we recommend you register your warranty
online at www.aquapor t/warranty

CUSTOMER HOTLINE: [phone]
Aquaport Corporation Pty Ltd
PO Box 81 Findon SA 5023 Australia
Telephone: [phone]
Facsimile: 08 8354 0722
Email: [e-mail]
Web: www.aquaport.com.au