
AQUATOP’S SkyAqua Marine LED lights bring life and brilliance to your marine aquarium.
These high output light xtures provide the proper spectrum for your marine life with the
shimmer of natural sunlight over a coral reef. The adjustable mounting system allows much
exibility for many size aquariums.
Please reference this manual for any questions and directions for use. May Aquatop’s
SkyAqua LED Series of aquarium lights serve you and your aquatic creatures well.
Note: Never put the unit inside the aquarium or immerse in water. It is your sole responsibility
to verify that the plug and the receptacle are clean and free of moisture and salt build up at all
times. The receptacle must be free of water, salt, calcium, magnesium and dust. Failure to do
so can cause re, damage to property, and permanent damage to the product and personal
injury not limited to loss of life.
• Intended for marine aquariums, but can be used on freshwater aquariums.
• Use more than one xture to increase light intensity even more!
• Convenient remote control included.
• Low Prole.
• Long Lifespan - no bulbs to replace.
• UL Listed.
• In the event of power failure, light will return to previously set mode once power is restored.
• Always install light on a covered aquarium only. Do not install over open water as this
presents a hazard and will void the warranty.
• Light should not be submerged, must remain dry and ventilated.
• Always utilize a drip loop on any electrical equipment used on or near an aquarium.
• Please note, the inline power switch contains an Infrared Eye. The remote control unit must
have a clear line of sight to this eye for proper functionality.
• Install the light xture over a properly covered aquarium. Do not install over open water.
• Light should not be submerged or allowed to get wet.
• Utilize extendable mounting legs to properly mount your light to the frame or glass edge
of your aquarium.
• Read and follow all instructions.
• A drip loop must be used with all electrical aquarium devices.
• A drip loop is a self-made part of the cord hanging below the receptacle.
(See Fig. 1)
• A GFCI (Ground Fault Circuit Interrupter) should be used in the branch
circuit supplying all power to water pumps and electricalaquarium equipment. If you
do not have a GFCI, we strongly recommend having a qualied electrician install one
prior to operating any aquarium component.
• Do not plug into extension cord/power strip.
• Use this product for its intended purpose only.
• Never yank or pull the cord from the electrical outlet.
• Do not operate if the plug or wire is damaged.
• Verify that hands are dry prior to disconnecting the power.
• To reduce the risks of electrocution, keep all connections dry.
• Make sure to unplug all electrical aquarium devices before installing the unit or performing
any type of maintenance on the unit.
• Before cleaning the unit unplug from power source. Use a clean damp cloth. Let unit
completely dry before plugging back into power source.
• For indoor use only.
• If any ofthe electrical components get wet, unplug immediately.
• Do not use soaps or detergents when cleaning the exterior surface of this device.
• Make sure the device is completely dry before connecting.
• Keep this product away from children and those who are unfamiliar with the unit and its
instruction manual.
1 2
ABOUT THE SKYAQUA LED SERIES
WARNINGS & SAFEGAURDS
FEATURES
SPECIFICATIONS AND SAFEGUARDS
OPERATING AND INSTALLATION INSTRUCTIONS
Model MAQ-1218 MAQ-1824 MAQ-2430 MAQ-3036 MAQ-3642 MAQ-4854
For Tank Sizes 12”-18” 18-24” 24”-30” 30”-36” 36”-42” 48”-54”
White LEDS 36 48 60 80 96 120
Red/ Blue LEDS 12 16 20 28 32 40
Wattage 12W 18W 21W 30W 33W 40W
Lumens 4000 4500 4500 4500 4500 5000
PAR 80 80 85 95 95 100
CRI >85 >85 >85 >85 >85 >85