AR 757 User manual

FR
EN
DE
IT
ES
PT
EL
NL
DA
NO
FI
SV
CS
PL
SL
SK
LT
BG
RU
HU
RO
TR
HR
LV
ET
cod. 90644 - LW
UK
757 - 767

2
FR Lire ce manuel avant l’installation/utilisation du nettoyeur en faisant très attention aux INSTRUCTIONS POUR LA SÉCURITÉ
EN Read this manual through carefully before installing/using the cleaner, paying special attention to the SAFETY
INSTRUCTIONS
DE Lesen Sie dieses Handbuch vor der Installation und dem Gebrauch des Hochdruckreinigers aufmerksam durch und achten
Sie besonders auf die SICHERHEITSANWEISUNGEN
IT Leggere questo manuale prima dell’installazione/uso dell’idropulitrice, prestando particolare attenzione alle ISTRUZIONI
PER LA SICUREZZA
ES Leer este manual antes de la instalación/uso de la hidrolimpiadora, prestando particular atención a las INSTRUCCIONES
SOBRE SEGURIDAD
PT Leia este manual antes de instalar/usar a lavadora a alta pressão, prestando muita atenção nas INSTRUÇÕES PARA A
SEGURANÇA
EL Διαβάστε το παρόν εγχειρίδιο πριν από την εγκατάσταση/χρηση του μηχανήματος πλύσης, με ιδιαίτερη προσοχή στις
ΟΔΗΓΙΕΣ ΓΙΑ ΤΗΝ ΑΣΦΑΛΕΙΑ
NL Lees vóór de installatie/het gebruik van de hogedrukreiniger deze handleiding goed door en in het bijzonder de
VEILIGHEIDSVOORSCHRIFTEN
DA Læs denne vejledning inden installation og brug af højtryksrenseren og vær særligt opmærksom på SIKKERHEDSREGLERNE
NO Les denne håndboken før installasjon og bruk av høytrykksspyleren og vær spesielt oppmerksom på SIKKERHETSREGLENE
FI Lue tämä käyttöopas ennen painepesurin asennusta/käyttöä. Kiinnitä erityistä huomiota TURVAOHJEISIIN
SV Läs igenom bruksanvisningen före installation och användning av högtryckstvätten. Lägg speciellt märke till
SÄKERHETSBESTÄMMELSERNA
CS Před instalací nebo používáním tohoto čističe si pečlivě přečtěte tuto příručku. Zvýšenou pozornost věnujte části
BEZPEČNOSTNÍ POKYNY
PL Przed przystąpieniem do instalacji bądź użycia myjki należy dokładnie przeczytać niniejszy podręcznik, zwracając
szczególną uwagę na treść części dotyczącej INSTRUKCJI BEZPIECZEŃSTWA
SL Pozorno preberite ta navodila pred namestitvijo/uporabo čistilnika, pri čemer posebno pozornost namenite VARNOSTNIM
NAVODILOM
SK Pred inštaláciou/používaním čističa si pozorne prečítajte tento návod a buďte obzvlášť opatrní pri čítaní BEZPEČNOSTNÝCH
POKYNOV
LT Prieš sumontuodami ir naudodami įrenginį atidžiai perskaitykite šią naudojimo instrukciją, ypatingą dėmesį atkreipdami
į SAUGOS INSTRUKCIJAS
BG Прочетете това ръководство внимателно, преди да инсталирате/използвате машината за почистване,
като обърнете особено внимание на ИНСТРУКЦИИТЕ ЗА БЕЗОПАСНОСТ
RU Прочитайте данное руководство перед установкой моечной машины, обращая особенное внимание на
ИНСТРУКЦИИ ПО БЕЗОПАСНОСТИ
HU A tisztítóberendezés üzembehelyezése/használata előtt olvassa át gondosan ezt a leírást, különös figyelmet szentelve a
BIZTONSÁGI ELŐÍRÁSOK című résznek
RO Citiţi acest manual în întregime cu atenţie înainte de a instala/utiliza aparatul de curăţat, acordând o atenţie mărită
INSTRUCŢIUNILOR DE SIGURANŢĂ
TR Hidro temizleyiciyi kurmadan/kullanmadan önce, EMNİYET BİLGİLERİ’NE özellikle dikkat göstererek, işbu kılavuzu
okuyunuz
HR Prije montiranja/korištenja čistača pažljivo pročitajte ovaj priručnik i posebnu pozornost posvetite SIGURNOSNIM
MJERAMA
LV Pirms tīrīšanas ierīces uzstādīšanas/izmantošanas izlasiet šo rokasgrāmatu, īpaši vērīgi lasiet DROŠĪBAS NOTEIKUMUS
ET Lugege see kasutusjuhend enne survepesuri töökorda seadmist/kasutamist hoolega läbi, pöörates erilist tähelepanu
OHUTUSNÕUETELE
UK Перед тим, як встановлювати/використовувати пристрій для миття, уважно прочитайте цей посібник,
звертаючи особливу увагу на ІНСТРУКЦІЇ З БЕЗПЕКИ

3
1
A2
A3
A1
C1
C5
B6
B1 D
B2
B2
C2
B3
B5
E1E3
B4

4
2
1 2
4 53
7
8
CH 17
Ø13
6757 767
757 767

5
3
4
E
F
I
D
2
1
G
psi
bar
0max
H
OFF
ON

6
I
5
Volt
230 3 x 1,5 mm23 x 2,5 mm2
1 ÷ 25 m 25 ÷ 50 m
M
L
P1
P2
3
S
n
M
1 ~
b
a
C
N
L1
r
6
S
m
b
N
N C
P = O
757 767
4
1
5
S
n
M
1 ~
b
a
C
N
L1 r
2 T

12
English
1
SAFETY INSTRUCTIONS
1.1 The appliance you have purchased is a technologically advanced
product designed by one of the leading European manufacturers
of high pressure pumps. To obtain the best performance from
your unit, read this booklet carefully and follow the instructions
each time you use it. During connection, use and servicing of
the appliance, take all possible precautions to protect your own
safety and that of the people in the immediate vicinity. Read the
safety regulations carefully and comply with them on all occasions;
failure to do so may put health and safety at risk or cause expensive
damage.
2
SAFETY RULES/RESIDUAL RISKS
2.1 SAFETY “MUST NOTS”
2.1.1
explosion or poisoning hazard.
DO NOT use the appliance with
inflammable or toxic liquids, or any products which are not
compatible with the correct operation of the appliance.
2.1.2
injury hazard.
DO NOT direct the water jet towards
people or animals.
2.1.3
electric shock hazard.
DO NOT direct the water jet
towards the unit itself, electrical parts or towards
other electrical equipment.
2.1.4
short circuit hazard.
DO NOT use the appliance outdoors
when it is raining.
2.1.5
injury hazard.
DO NOT allow children or incompetent
persons to use the appliance.
2.1.6
electric shock hazard.
DO NOT touch the plug
and/or socket with wet hands.
2.1.7
electric shock and short circuit hazard.
DO
NOT use the appliance if the electrical cable is
damaged.
2.1.8
explosion hazard.
DO NOT use the appliance if the
high pressure hose is damaged.
2.1.9
accident hazard.
DO NOT jam the trigger in the operating
position.
2.1.10
accident hazard.
Check that the data plates are affixed to
the appliance, if not, inform your dealer. Units without
plates must NOT be used as they are unidentifiable and potentially
dangerous.
2.1.11
explosion hazard.
DO NOT tamper with or adjust
the setting of the safety valve or the safety devices.
2.1.12
hazardous alteration of operating performance.
DO NOT
alter the original diameter of the spray head nozzle.
2.1.13
accident hazard.
DO NOT leave the appliance unattended.
2.1.14
short circuit hazard.
DO NOT move the appliance by
pulling on the ELECTRICAL CABLE.
2.1.15 Make sure that cars do not drive over the high pressure hose.
2.1.16
explosion hazard.
DO NOT move the appliance by pulling on the
high pressure hose.
2.1.17
explosion hazard.
When directed towards tyres, tyre valves or
other pressurised components, the high pressure jet is potentially
dangerous. Do not use the rotating nozzle kit, and always keep the
jet at a distance of at least 30 cm during cleaning.
2.2 SAFETY “MUSTS”
2.2.1
short circuit hazard.
All electrical conductors MUST BE
PROTECTED against the water jet.
2.2.2
electric shock hazard.
The appliance MUST ONLY
BE CONNECTED to an adequate power supply in
compliance with all applicable regulations (IEC 60364-1).
The appliance may cause network noise DURING startup.
• Use of a safety residual current circuit-breaker (R.C.C.B.) will
provide additional protection for the operator (30 mA).
Models supplied without plug must be installed by qualified staff.
Use only authorized electrical extension leads with suitable
conductor gauge.
2.2.3
injury hazard.
High pressure may cause parts to rebound: wear
all the protective clothing and equipment needed to ensure the
operator’s safety.
2.2.4
accidental start-up hazard.
Before doing work on the
appliance, REMOVE the plug.
2.2.5
injury hazard.
Before pressing the trigger, GRIP the gun
firmly to counteract the recoil.
2.2.6
contamination hazard.
COMPLY WITH the
requirements of the local water supply company.
According to DIN 1988, the appliance may only be connected to
the mains drinking water supply if a backflow preventer valve with
drain facility is installed in the supply hose.
2.2.7
accident hazard.
Maintenance and/or repair of electrical
components MUST be carried out by qualified staff.
2.2.8
injury hazard.
DISCHARGE residual pressure before
disconnecting the unit hose.
2.2.9
accident hazard.
Before using the appliance, CHECK every
time that the screws are fully tightened and that there are
no broken or worn parts.
2.2.10
explosion and electric shock
hazard.
ONLY USE detergents
which will not corrode the coating materials of the high pressure
hose/electrical cable.
2.2.11
injury hazard.
ENSURE that all people or animals
keep a minimum distance of 16 yd. (15m) away.

13
English
EN
3
GENERAL INFORMATION FIG.1/PAGE 3
3.1 Use of the manual
This manual forms an integral part of the appliance and should be
kept for future reference. Please read it carefully before installing/
using the unit. If the appliance is sold, the Seller must pass on this
manual to the new owner along with the appliance.
3.2 Delivery
The appliance is delivered partially assembled in a cardboard box.
The supply package is illustrated in fig.1.
3.2.1 Documentation supplied with the appliance
A1 Use and maintenance manual
A2 Safety instructions
A3 Declaration of conformity
A4 Warranty regulations
3.3 Disposing of packaging
The packaging materials are not environmental pollutants but must
still be recycled or disposed of in compliance with the relevant
legislation in the country of use.
3.4 Safety signs
Comply with the instructions provided by the safety signs fitted to
the appliance.
Check that they are present and legible; otherwise, fit replacements
in the original positions.
E1 symbol – Indicates that the appliance must not be dis-
posed of as municipal waste; it may be handed in to the
dealer on purchase of a new appliance. The appliance's electrical
and electronic parts must not be reused for improper uses since
they contain substances which constitute health hazards.
E2 symbol – Indicates that the appliance is intended for
professional use, i.e. for experienced people informed
about the relative technical, regulatory and legislative aspects and
capable of performing the operations necessary for the use and
maintenance of the appliance.
E3 symbol – Indicates that the appliance is intended for
non-professional (domestic) use.
4
TECHNICAL INFORMATION FIG.1/PAGE 3
4.1 Envisaged use
This appliance has been designed for individual use for the cleaning
of vehicles, machines, boats, masonry, etc, to remove stubborn dirt
using clean water and biodegradable chemical detergents.
Vehicle engines may be washed only if the dirty water is disposed of
as per regulations in force.
- Intake water temperature: see data plate on the appliance.
- Intake water pressure: min. 0,1MPa-max 1MPa.
- Operating ambient temperature: above 0°C.
The appliance is compliant with the EN 60335-2-79/A1 standard.
4.2 Operator
The symbol on the front cover identifies the appliance’s intended
operator (professional or non-professional).
4.3 Improper use
Use by unskilled persons or those who have not read and under-
stood the instructions in the manual is forbidden.
The introduction of inflammable, explosive and toxic liquids into the
appliance is prohibited.
Use of the appliance in a potentially inflammable or explosive
atmosphere is forbidden.
The use of non-original spare parts and any other spare parts not
specifically intended for the model in question is prohibited.
All modifications to the appliance are prohibited. Any modifications
made to the appliance shall render the Declaration of Conformity
null and void and relieve the manufacturer of all liability under civil
and criminal law.
4.4 Main components
B1 Adjustable spray nozzle B5 High pressure hose
B2 Lance B6 Detergent tank
B3 Gun with safety catch (on models with this feature)
B4 Power supply cable with plug (on models with this feature)
4.4.1 Accessories (if included in the supply package – see fig.1).
C1 Nozzle cleaning tool C7 Pipe drain kit
C2 Rotating nozzle kit C8 Large surface
C3 Handle cleaning tool
C4 Brush C9 Adapter
C5 Hose reel C10 Lubricating grease tube
C6 Water suction kit (where supplied)
4.5 Safety devices
Caution - Danger!
Do not tamper with or adjust the safety valve setting.
- Safety valve and/or pressure limiting valve.
The safety valve is also a pressure limiting valve.
When the gun trigger is released, the valve opens and the water
recirculates through the pump inlet or is discharged onto the ground.
- Thermostat valve (D1 where fitted)
If the water temperature exceeds the temperature set by the
manufacturer, the thermostat valve discharges the hot water and
draws in an amount of cold water equal to the amount of water
discharged, until the correct temperature is restored.
- Safety catch (D): prevents accidental spraying of water.
5
INSTALLATION FIG.2/PAGE.4
5.1 Assembly
Caution - Danger!
All installation and assembly operations must be
performed with the appliance disconnected from the mains
power supply.
The assembly sequence is illustrated in fig.2.
5.2 Assembling the rotating nozzle
(For models with this feature)
The rotating nozzle kit delivers greater washing power.
Use of the rotating nozzle may cause of reduction in pressure of
25% compared to the pressure obtained with the adjustable nozzle.
However, the rotating nozzle kit delivers greater washing power due
to the rotation of the water jet.
5.3 Electrical connection
Caution - Danger!
Check that the electrical supply voltage and frequen-
cy (V-Hz) correspond to those specified on the appliance
data plate (fig.2). The appliance should only be connected
to a mains power supply equipped with an adequate earth
connection and a differential security breaker (30 mA) to cut
off the electricity supply in the instance of a short circuit.
5.3.1 Use of extension cables
Use cables and plugs featuring“IPX5”protection level.
The cross-section of the extension cable should be pro-
portionate to its length; the longer it is, the greater its
cross-section should be. See table I/PAGE 6.
5.4 Water supply connection
Caution - Danger!
Only clean or filtered water should be used for intake.
The delivery of the water intake tap should be equal to that
of pump capacity.
Place the appliance as close to the water supply system as possible.
5.4.1 Connection points
l Water outlet (OUTLET)
n Water inlet with filter (INLET)
5.4.2 Connection to the mains water supply
The appliance can be connected directly to the mains drinking
water supply only if the supply hose is fitted with a backflow pre-
venter valve as per current regulations in force. Make sure that the
hose is at least Ø 13 mm and that it is reinforced.

14
English
EN
6
ADJUSTMENT INFORMATION FIG.3/PAGE 5
6.1 Adjusting the spray nozzle (for models with this feature)
Water flow is adjusted by regulating the nozzle (E).
6.2 Adjusting the detergent (on models with this feature)
Detergent flow is adjusted using the regulator (F).
6.3 Adjusting the detergent pressure
Set the adjustable nozzle (E) on " " to deliver detergent at the
correct pressure (on models with this feature).
6.4 Adjusting the pressure (on models with this feature)
The regulator (G) is used to adjust the working pressure. The pres-
sure is shown on the pressure gauge (where fitted).
7
INFORMATION ON USE OF THE APPLIANCE FIG.4/PAGE 5
7.1 Controls
- Starter device (H).
Set the starter switch on (ON/1) to:
a) start the motor (in models without TSS device);
b) set the motor ready to start (in models with TSS device).
If there is a pilot light on the starter device, it should light up.
If the “low/high”settings are available, use them as follows:
Low : low pressure washing
High : high pressure washing
Set the starter device switch on (OFF/0) to shut down the appliance.
If there is a pilot light on the starter device, it should go out.
- Water jet control lever (I).
Caution - Danger!
During operation the appliance must be positioned
as shown in fig. 4 on a sturdy, stable surface.
7.2 Start-up
1) Turn on the water supply tap fully.
2) Release the safety catch (D).
3) Depress the gun trigger for a few seconds and start up the appli-
ance using the starter device (ON/1).
Caution - Danger!
Before starting up the appliance check that the water
supply hose is connected properly; use of the appliance
without water will damage it; do not cover the ventilation
grilles when the appliance is in use.
TSS models - In TSS models with automatic delivery flow cut-off
system:
- when the gun trigger is released the dynamic pressure automati-
cally cuts out the motor (see fig.4);
- when the gun trigger is depressed the automatic drop in pres-
sure starts the motor and the pressure is restored after a very
slight delay;
- if the TSS is to function correctly all gun releasing and depress-
ing operations must be performed at intervals not less than 4-5
seconds at least.
On three-phase models for professional use: at first use, start the
appliance for a very short time to check that the motor is running
in the correct direction. If the motor fan is turning anti-clockwise,
exchange two of the three phase wires (L1, L2, L3) in the electri-
cal plug.
To prevent damage to the appliance, do not allow it to oper-
ate dry and when running do not stop the water jet for more
than 10 minutes at a time (for models without TSS device).
7.3 Stopping the appliance
1) Set the starter device switch on (OFF/0).
2) Depress the gun trigger and discharge the residual pressure
inside the hoses.
3) Engage the gun safety catch (D).
7.4 Restarting
1) Release the safety catch (D).
2) Depress the gun trigger and discharge the residual air inside
the hoses.
3) Set the starter device on (ON/1).
7.5 Storage
1) Switch the appliance off (OFF/0).
2) Remove the plug from the socket.
3) Turn off the water supply tap.
4) Discharge the residual pressure from the gun until all the water
has come out of the nozzle.
5) Drain and wash out the detergent tank at the end of the work-
ing session. To wash out the tank, use clean water instead of
the detergent.
6) Engage the gun safety catch (D).
7.6 Refilling and using detergent
When using detergent, the adjustable nozzle must be set on
" " (on models with this feature).
Use of a high pressure hose longer than the one originally supplied
with the cleaner, or the use of an additional hose extension, may
reduce or completely halt the intake of detergent.
Fill the tank with highly degradable detergent.
7.7 Recommended cleaning procedure
Dissolve dirt by applying the detergent mixed with water to the
surface while still dry.
When dealing with vertical surfaces work from the bottom upwards.
Leave the detergent to act for 1-2 minutes but do not allow the
surface to dry. Starting from the bottom, use the high pressure jet
at a minimum distance of 30 cm. Do not allow the rinse water to run
onto unwashed surfaces.
In some cases, scrubbing with brushes is needed to remove dirt.
High pressure is not always the best solution for good washing
results, since it may damage some surfaces. The finest adjustable
nozzle jet setting or the rotopower nozzle should not be used on
delicate or painted parts, or on pressurised components (e.g tyres,
inflation valves, etc.).
Effective washing depends on both the pressure and volume of the
water used, to the same degree.
8
MAINTENANCE FIG.5/PAGE 6  FIG.6/PAGE 144
Any maintenance operations not covered by this chapter should be
carried out by an Authorized Sales and Service Centre.
Caution - Danger!
Always disconnect the plug from the power socket
before carrying out any work on the appliance.
8.1 Cleaning the nozzle
1) Disconnect the lance from the nozzle.
2)
Remove any dirt deposits from the nozzle hole using the tool (C1).
8.2 Cleaning the filter
Inspect the intake filter (L) and detergent filter (if fitted) before each
use, and clean in accordance with the instructions if necessary.
8.3 Unjamming the motor (on models with this feature)
In case of lengthy stoppages, limescale sediments may cause the
motor to seize. To unjam the motor, turn the drive shaft with a
tool (M).
8.4 End-of-season storage
Treat the appliance with non-corrosive, non-toxic antifreeze and
lubricate the O-rings using the lubricating grease tube (where sup-
plied) (C10) as shown before storing it away for winter.
Put the appliance in a dry place, protected from frost.

15
English
EN
9
TROUBLESHOOTING
Problem Possible causes Remedy
Pump does not reach working
pressure
Nozzle worn Replace nozzle
Water filter fouled Clean filter (L) (fig.5)
Water supply pressure low Turn on water supply tap fully
Air being sucked into system Check tightness of hose fittings
Air in pump
Switch off the appliance and keep depressing and releas-
ing the gun trigger until the water comes out in a steady
flow. Switch the appliance back on again.
Adjustable nozzle not positioned correctly Turn the adjustable nozzle (E) (+) (fig.3)
Thermostatic valve tripped Wait for correct water temperature to be restored
Pressure drops during use
Water intake from external tank Connect appliance to the mains water supply
Intake water too hot Reduce temperature
Nozzle clogged Clean nozzle (fig.5)
Intake filter (L) dirty Clean filter (L) (fig.5)
Motor “sounds” but fails to start
Insufficient power supply Check that the voltage of the mains power supply line is
the same as that on the plate (fig.2)
Voltage loss due to use of extension cable Check characteristics of extension cable
Appliance not used for a long period of time Contact your nearest Authorized Service Centre
Problems with TSS device Contact your nearest Authorized Service Centre
Motor fails to start
No electrical power Check that the plug is firmly in the socket and that the
mains voltage supply is present (*)
Problems with TSS device Contact your nearest Authorized Service Centre
Appliance not used for a long period of time Using the tool (M) unjam the motor from the hole at the
rear of the appliance (in models with this feature) (fig.5)
Water leakage Seals worn Have the seals replaced at your nearest Authorized
Service Centre
Safety valve tripped and discharging Contact an Authorized Service Centre
Appliance noisy Water too hot Reduce temperature (see technical data
Oil leakage Seals worn Contact your nearest Authorized Service Centre
TSS versions only: motor starts
even with gun trigger is released
High pressure system or pump hydraulic circuit not
watertight Contact your nearest Authorized Service Centre
TSS versions only: no water deliv-
ery when gun trigger is depressed
(with supply hose connected)
Nozzle clogged Clean nozzle (fig.5)
No detergent taken in
Adjustable nozzle on high pressure setting Set nozzle on " " setting (fig.3)
Detergent too dense Dilute with water
High pressure hose extension being used Fit original hose
Deposits or restriction in detergent circuit Flush with clean water and eliminate any restrictions. If the
problem persists, contact an Authorized Service Centre
(*) If the motor starts and does not restart during operation, wait 2-3 minutes before repeating the start-up procedure (overload cutout has been tripped).
If the problem recurs more than once, contact your nearest Authorized Service Centre.
MODEL SERIAL NUMBER

16
English
EN
Technical Data (EN) Unit 757
767
Output
l/min
8,3 10
Pressure MPa
12 11
Maximum pressure MPa
13 13
Power kW
2,2
2,6
T° input °C
60
60
Maximum input
pressure
MPa
1 1
Repulsive force of the
gun to the maximum
pressure
N
18,1 24,5
Motor Insulation -
Class F Class F
Motor Protection -
IPX5 IPX5
Voltage V/Hz
230-240/50
230-240/50
Maximum allowed net
impedance
Ω - -
Sound level K = 3 dB(A) :
L
PA
(EN 60704-1)
dB (A) 82
80
L
WA
(EN 60704-1)
dB (A) 90
88
Unit vibrations K =
1,5
m/s2 :
m/s
2
4,91
4,91
Weight kg
34
34
(EN) WARRANTY
The duration of the warranty is in accordance with the relevant legislation in the country where the product is sold (unless
otherwise stated by the producer).
The warranty covers materials, construction and conformity defects during the warranty period, during which time the
manufacturer will replace defective parts and repair or replace the product if excessively worn in normal use.
The warranty does not cover components subject to normal wear (valves, pistons, water gasket, oil gasket, springs, O-rings,
accessories such as hoses, guns, brushes, wheels, etc.).
The warranty does not cover defects caused by or resulting from:
- incorrect use, abuse or neglect,
- trade, professional or hire use,
- failure to service and maintain the unit as specified in the user’s manual,
- unauthorised repairs,
- use of non-original accessories/spare parts,
- damage incurred during shipping or due to foreign objects or substances and accidental damage,
- warehousing and stock keeping problems.
To register the warranty, the customer must provide proof of purchase.
For service, contact the dealership where the machine was purchased
EN EC Declaration of conformity
We Annovi Reverberi S.p.A., Bomporto (Mo),Italy declare that the
following PROLINER S - SV Machine(s):
Designation of Machine High PressureWasher
Model No / Type 757 767
Input power 2,2 kW 2,6 kW
Conforms to the following European Directives:
2006/42/EC, 2006/95/EC, 2011/65/EC, 2002/96/EC, 2004/108/EC,
2000/14/EC
And are manufactured in accordance to the following standards or
standardised documents: EN 60335-1; EN 60335-2-79; EN 55014-1; EN
55014-2; EN 61000-3-2; EN 61000-3-3; EN 61000-3-11; EN 60704-1
Name and address of the person in charge to give the technical file:
Stefano Reverberi / AR Managing Director
Via M. L. King, 3 - 41122 Modena, Italy
The conformity assessment procedure required by Directive 2000/14/EC
was in accordance with annexV
757 767
Measured Sound
Power Level: 89 dB (A) 87 dB (A)
Guaranteed Sound
Power Level: 90 dB (A) 88 dB (A)
Date: 03.06.2013
MODENA (I)
Stefano Reverberi Managing Director
Technical Data
Subject to technical modifications!

138 ✍

139
✍

Annovi Reverberi S.p.A.
Via M.L. King 3
41122 Modena (Italy)
www.annovireverberi.it