Arada Aarrow DEFRA User manual

DEFRA Stove
Installation and User Guide
BK575
February 2013
PLEASE RETAIN THIS GUIDE FOR FUTURE REFERENCE
EN 13240:2001+ Amd. A2:2004
For stoves ranges:
Aarrow DEFRA
Signature DEFRA
Ecoburn DEFRA
Solution DEFRA

WARNINGS
It is a legal requirement that the installation of all new or replacement wood fuel
heating appliances must obtain building control approval from your local authority.
Please consult health and safety guidelines for advice on handling heavy and/or large items.
Any manufacturer’s instructions must not be taken as overriding statutory requirements.
The installation must comply with all current building regulations and any additional local
ordinances. Installation work must be carried out by a qualified heating engineer, affiliated to
a government approved competent persons scheme such as operated by HETAS.
During installation ensure that adequate precautions are taken to avoid unnecessary risk to
yourself or any householder. In particular the danger from the caustic nature of fire cement
should be avoided by using these accepted methods; wear gloves when handling fire
cement and goggles when chiselling or looking up chimneys.
If in doubt, contact HETAS Ltd. T: 0845 634 5626 W: www.hetas.co.uk
A fireguard conforming to BS 8423:2002 should be used in the presence of children and old or
infirm people.
Do not use aerosol sprays or any other flammable materials near the appliance when in use.
Arada Ltd will not be responsible for any consequential or incidental loss or injury however
caused.
Arada has a policy of continuous product development and therefore we reserve the right to
amend the specification without prior notice.
Due to printing cycles, items or options may be described before they are generally available
or after they have ceased.
More than 20 years experience has been put into the development of our stoves to ensure
ultimate performance and years of trouble free use and enjoyment.
Every detail of the stove has been carefully designed and engineered which is why we are
so confident in the reliability of our products.
Should you have any questions about our stoves that are not covered by this manual, please
contact the Arada retailer in your area, or call our technical support department on
08448 567181 .
All Arada stoves are tested to European Standard EN 13240.
DEFRA Stove Installation and User Guide
2

HEARTH
The stove should be installed on a floor with
adequate load bearing capacity. If the
existing construction does not meet this
prerequisite, suitable measures (e.g. load
distributing plate) should be taken to achieve it.
Ideally, the appliance should stand on a
constructional hearth of non-combustible
materials not less than 125mm (5”) thick
conforming to Building Regulations.
Dimensions of the hearth should project at least
225mm (9”) forward of the front of the appliance
and 150mm (6”) at the sides. The surface of the
hearth should be free of combustible materials.
Certain stoves manufactured by Arada are
suitable for installation on a non-combustible
12mm hearth such as glass. Please consult the
technical table found at the rear of the user
guide for a list of suitable models.
COMBUSTIBLE MATERIALS
Please view the technical data table in the rear
of the user guide and observe the minimum
distance to combustible materials, which is
applicable to your stove model.
Ideally, adjacent walls should be of suitable
non-combustible construction, preferably
brickwork. In large fireplaces take care that any
supporting beam is protected by a 13mm (0.5”)
sheet of Masterboard or Superlux spaced 12mm
(0.5”) off the surface with strips of
non-combustible material. Make sure that there
is a gap between an un-insulated flue system
and any combustible material. This gap must be
at least 3X the outside diameter of the flue pipe,
or 1.5X the flue diameter to non combustible
surfaces.
INSTALLAITON INSTRUCTIONS
DEFRA Stove Installation and User Guide 3
AIR FOR COMBUSTION
All stoves require ventilation to burn safely and
correctly. There are requirements that need to
be met when installing a stove, such as
allowing for the permeability of the house (air
permeability is the general seepage of air into
the house via air vents, doors and windows
etc.).
There must always be a permanent means of
providing air for combustion into the room in
which the stove is installed.
For guidelines on required ventilation sizes
please refer to the ‘HETAS Guide’ which can
be found on HETAS’ website.
The positioning of any air vent must be so that
it cannot be liable to blockage or obstruction.
The fitting of an extractor fan in the same room
as the stove, or an adjacent room is not
permitted.
FITTING THE FLUE OUTLET
The flue outlet spigot may be fitted onto the
stove, but will not be fully tightened.
The flue outlet assembly can be orientated for
top or rear flue exit as shown in fig 1a & b on
page 4.
The outlet pipe flange is pre fitted with a
gasket rope seal. Additional fire cement may
be added if required.
The flue pipe assembly is secured in place with
four M5 bolts (supplied). Tighten bolts
diagonally and evenly to ensure full
compression of the gasket but do not over
tighten.
Place appliance on the hearth and make sure
that it is level and does not rock.
Connect the chimney ensuring all joints are

sealed with fire cement.
Note : The flue pipe must be fitted inside the outlet
spigot. Failure to do so could result in the spillage
of condensation running down the flue, (see
fig.1c)
ADJUSTING THE SELF
LEVELLING FEET IF APPLICABLE
Adjustment is as follows:
 Position the stove on the hearth into its final
resting place.
 On the rear leg of the stove, loosen the pozi
screw, and rotate the inner ‘cam’ shaped
levelling foot until this touches the hearth.
 Re-tighten the pozi screw. Check the stove is
level with a spirit level.
 Repeat for the other rear leg.
FIREBOX LINER PANELS
Arada DEFRA stove uses firebox liner panels at
both sides of the stove. The throat plate is not
supported by these liners, however the throat
plate must be installed before the liners can be
fitted, and the liners removed before the throat
plate can be removed.
To remove / fitting the liners
 Open the fire door.
 Remove the wood burning tray
 Remove the lower side liners, carefully
allowing the upper side liners to slide down
to the landing plate
 Remove the upper side liners
 Replacing or fitting the liners is the reverse
of this procedure
Note : Cracking of the liner panels does not
effect the normal use or efficiency of the stove.
FITTING THE THROAT PLATE
This must be carried out with the wood
burning tray and side liners removed.
4
INSTALLATION INSTRUCTIONS
DEFRA Stove Installation and User Guide

All images below are cut-away for clarity
1. Insert throat plate assembly into the fire
box and manoeuvre so that the throat
plate drops into the landing plate cut-
outs.
2. Raise the throat plate assembly verti-
cally out of the landing slots ensuring
the front edge remains behind the front
edge of the air wash lip, see fig 4.
3. Hook the throat plate ‘T’ cut-out onto
the support hanger and push back to
slide onto the secondary air tube; the
wood tray will hold the bottom edge
into the correct position.
GRATE BARS
In a multi fuel stove, the grate comprises of a
series of cast iron grate bars seated on a pair
of combs. All bars in the grate are identical.
The bars should be seated with every other
bar rotated 180 degrees, so the ends marked
’H’ and ’L’ alternate on each comb.
5
FLUES AND CHIMNEYS
The flue draw is critical on any installation and
should be checked to ensure that it matches
what is specified. If it is higher than
recommended, provisions must be made to
correct the over draw.
The draw can vary in different weather
conditions and the customer should be made
aware of this. Failure to correct an over
drawing flue will invalidate the warranty.
The stove must be connected to a suitable and
efficient flue so that products of combustion
(fumes) from the stove are expelled to the
outside air. To ensure a good up draught it is
important that the flue gases are kept warm
and that the flue size suits the stove. The termi-
nation of the outlet at the top of the flue also
needs to comply with Building Regulations. The
minimum effective height of the flue must be at
least 4.5 metres from the top of the stove to the
top of the flue outlet. When warm the flue
draught should be between 0.1 to 0.2 mb.
A chimney may comply with regulations but
could still be subject to down draught and
similar problems. A chimney terminating above
the ridge level is generally less likely to suffer
such problems.
If a new chimney is being built / installed it
should fully comply with the relevant Building
Regulations that specify the requirements for
solid fuel burning installations.
The flue and chimney installation must be
carefully checked by a competent person
before fitting the stove to ensure it is suitable
and will work safely.
If the chimney is old (ie: built of brick or stone
without a liner) or being opened up for reuse
additional checks and smoke testing as
described in Appendix E of the Approved
Document J 2002 Edition should also be
carried out to ensure the flue and chimney are
INSTALLATION INSTRUCTIONS
DEFRA Stove Installation and User Guide

6
INSTALLATION INSTRUCTIONS
in good operating condition.
Check the existing flue is in good condition with
suitable access for collection and removal of
debris. If the flue size is more than 225mm (9”)
diameter or 200mm (8”) X 200mm (8”) square, a
suitable lining of 150mm (6”) diameter should
be fitted. Approved Document J 2010 allows
for the use of a 5” liner / flue for wood burning
when a stove that is DEFRA exempt is installed.
This is as a result of the very clean burning
nature of DEFRA exempt stoves, when
operated in strict accordance to the user
manual.
If the DEFRA exempt stove is replaced at any
time with a NON DEFRA exempt stove, the
liner / flue must be changed to a 6” diameter
liner to conform to Building Regulations when
burning wood.
This should be a double skin stainless steel flexi-
ble liner that is independently certified for use
with solid fuel.
Details of suitable linings for use with wood fuel
are given in the HETAS guide that can be
viewed on their website at www.hetas.co.uk.
It is also important that suitable flue pipe,
complying with the Building Regulations, is used
to connect the stove to the flue in the
chimney, and that suitable access is provided
into the flue for regular inspection and
sweeping of the flue ways other than through
the appliance (e.g. wherever possible a soot
door or access through register plate).
Chimneys should be as straight as possible.
Horizontal runs should be avoided except
where the rear outlet of the appliance is used,
in which case the horizontal section should not
exceed 150mm (6”) in length.
If the stove appears to be working hard but
produces very little output to the room it is
likely that excess draw is present in the
chimney, and that heat is being sucked out of
the appliance and up the chimney. If this is the
case we recommend the fitting of a draught
stabiliser in preference to a flue damper, in the
interest of safety and efficiency.
The installer should comply with Building
Regulations requirements in respect of providing a
Notice Plate giving details on the chimney, flue
lining, hearth and fireplace installation.
FINAL CHECK LIST
Before handing over the installation to the
customer it is a requirement under Document J (of
the Building Regulations for England & Wales) that
the appliance is lit and the functioning of the
chimney system is checked for satisfactory
operation.
 Be sure that the chimney is operating and all
smoke and fumes are vented to the
atmosphere through the chimney
terminal.
 Check all joints and seals.
 Clean the outside of the appliance to
prevent any stains becoming burnt on.
 Check the flue draught which should read 1
- 2mm, or 0.1 - 0.2 mbar.
 For a registered competent persons
scheme, such as HETAS, please
complete a Certificate Of Compliance,
which is used for checking and reporting the
installation as imposed by the Government.
 Explain the controls and operation of the
appliance to the customer.
 Ensure a Carbon Monoxide alarm is
fitted. This must be between 1m to 3m of the
appliance, and approximately 150mm
below the ceiling level.
 A fireguard conforming to BS 8423:2002
should be used in the presence of
children and old or infirm people.
DEFRA Stove Installation and User Guide

7
USER GUIDE
FUEL TYPES
The most efficient use of this appliance is with
the fire door(s) closed at all times, apart from
re-fuelling (when alight) or cleaning (when
cold).
Never leave the appliance unattended for an
extended length of time with the door(s)
open.
If this is the case, a spark guard must be used
and the operating efficiency of the appliance
will decrease.
Wood
Any type of wood is suitable provided it is well
seasoned and has a moisture content below
20%. This usually implies that the timber has
been suitably stored to allow moisture to
evaporate for at least nine months in the case
of soft woods, and at least eighteen months in
the case of hard wood.
We recommend that for general burning,
wood should be split into logs of no more than
100mm(4”) diameter.
WARNING : Wet wood must not be used as
this will greatly contribute to the creation of
tar and creosote which may, in extreme
cases, run down the chimney in liquid form.
This will seriously damage both the chimney
and the appliance, and increase the risk of a
chimney fire.
Please Note : If you have sticky tar inside the
appliance or chimney your wood is ‘Green’ or
too wet.
Please Note : The burn classification for all
appliances in these instructions are classed as
intermittent use.
Paper
Paper will burn successfully. Burn dry paper only
or chimney damage will occur.
WARNING : Never burn plastics, household waste
or liquid fuels in your stove
Please contact Arada Ltd for further details and
advice on the use of other fuels.
Lighting the fire
Prior to lighting the stove for the first time, check
with the installer that:
• Installation and all building work is complete.
• The chimney is sound and has been swept and
is free from obstruction.
• Adequate provision for combustion air has
been made.
• That Building Regulations and any local by laws
have been followed during installation. See
installation section of this manual.
• All firebox liner panels and throat plate are in
place.
• That the chimney draw has been checked and
is within specification. With the chimney warm,
the draught should be between 1-2 mm water
gauge or 0.1 to 0.2 mbar.
WARNING : An over drawing chimney can cause
over firing, resulting in damage to the appliance.
Ensure that you have read and understood these
instructions before lighting the fire. Always wear
suitable protective fire gloves when refuelling
your stove.
DEFRA Stove Installation and User Guide

8
Important reminders for the user.
1. Take care to insure against blocking or
obstructing the permanent air ventilator fitted
to supply combustion air for the appliance.
2. Do not install an extractor fan in the same
room as the appliance or a room adjoining the
same room. If the installer considers this
unavoidable refer to Approved Document J
Section 1, Paragraphs 1.20 & 1.23 for guidance
HETAS Approval only covers the use of wood on
the appliance and does not cover the use of
other fuels either alone or mixed with other
fuels, nor does it cover instructions for the use of
other fuels.
Clean Burning of Wood
In order to burn wood cleanly, in accordance
with the DEFRA exception certificate
applicable to this stove, it is important that the
Ignition and Re-fuelling instructions are
followed carefully.
Ignition Sequence
(Lighting from cold)
Place a firelighter and a large handful (0.5-0.6
kg) of dry kindling in the stove. With the air
control set to maximum (fully to the left) light
the firelighter and push the door up to a point
where it is 10mm ajar.
After 8-10mins the kindling will die down, now
add four small split logs (approx 0.75kg in total)
once again leaving the door ajar 10mm and
the air control still at maximum. Once these
small logs are well alight, and with the burn
starting to slightly recede (depending on flue
draw etc. this may be up to 20 mins) add the
normal fuel load (approximately 1.3kg or two
small logs). After approximately 3 minutes shut
the door fully but leave the air control set to
maximum. When the logs have burnt down to
embers the “Ignition Sequence” is complete
and re-fuelling for normal use can commence.
The purpose of these ignition instructions
(lighting from cold) is to ensure that both the
stove and chimney are heated to full running
temperature as quickly as possible so avoid
smoke emissions during subsequent re-fuelling.
Re-fuelling
(Normal use after the ignition sequence)
When the stove requires re-fuelling (i.e. the
previous fuel load has died down to a glowing
ember bed), add two small logs with a total
weight of approximately 1.3kg. Leave the door
ajar 10mm and set the air control to maximum.
After 3 minutes close the door fully but leave the
air control to maximum. After a further 1 minute
the air control may be moved to the desired
running position (to the right). This procedure
should be followed on any subsequent
re-fuelling.
Important Information
When first lighting the stove always follow the
lighting sequence above to heat the stove and
flue/chimney as quickly as possible, never over
load the firebox.
Always re-fuel onto a hot bed of glowing
embers. Always ensure the fire is well alight after
re-fuelling before leaving the stove unattended.
The average fuel load of the stove is 1.3kg per
hour of dry well seasoned hardwood providing
approximately 4.5kWh of heat with the air
control set fully to the right stop.
In order to avoid overloading the firebox it is
recommended that a fuel load no greater than
1.5 kg is used during re-fuelling.
The recommended log size is approximately
250mm long and 90-100mm in diameter, of
which two would normally constitute one full
load for 1 hour burning at 4.5kw output.
DEFRA Stove Installation and User Guide
USER GUIDE

9
WARNING : Properly installed, with a suitable flue
or chimney, operated and maintained correctly,
this appliance will not emit fumes into the
dwelling.
Occasional fumes when de-ashing and
re-fuelling may occur. However, persistent fume
emission is potentially dangerous and must be
investigated by a HETAS registered installer.
Stop using the appliance if you smell fumes or
see smoke escaping.
If fume emission does persist, the following
immediate actions should be taken :
 Open doors and windows to ventilate
room then leave the premises.
 Let the fire go out.
 Check for flue or chimney blockage, and
clean if required.
 Your installer should have fitted a CO
Alarm in the same room as the appliance.
If the alarm sounds unexpectedly, follow
the instructions given under warning
above.
Seek expert advice from your HETAS registered
installer. Do not attempt to re-light the fire until
the cause of the fume emission has been
identified and corrected.
Please Note: The high temperature paint
requires durability by being “cured” during the
initial firings of the appliance. It will give off fumes
which are non toxic, but certain persons may
find they have an unpleasant or irritant effect.
Ensure that the surrounding area is well
ventilated during this time.
Over Firing and Chimney Fires
Do not over fire your appliance. Using flammable
liquids or too much wood or firing the stove at
maximum for prolonged periods may result in
over firing.
If the chimney connector or casing glows red
the appliance is being over-fired which may
result in a chimney fire. If this occurs :
 Call the Fire Service—Dial 999 or 112
 Immediately close all air inlets to the
appliance, to reduce the air supply to the
stove.
 Move items of furniture and combustibles
away from the stove, to reduce a risk of
fire and to allow access for the fire
service.
 Ensure access to the loft space is
available.
 Evacuate the property.
 The chimney fire may cause structural
damage to the chimney. Do not use the
appliance until the chimney and
connector have been inspected and any
damaged parts have been repaired or
replaced. This should be done by a HETAS
registered engineer.
Ash Removal
The appliance will require ash to be removed
periodically but an ash bed of approximately
20mm (3/4”) should be maintained.
Care must be taken not to risk burning of hands
or household objects from falling embers.
The ash pan should be emptied at least twice a
day or when the level of ash reaches the top of
the ash pan.
WARNING :
The ash can be very hot. Empty only into a
metal container. Even if the ash appears cold,
red hot pieces of ash may be concealed and
could easily start a fire or cause a serious injury
DEFRA Stove Installation and User Guide
USER GUIDE

Air Controls
Our DEFRA stoves have one air inlet
control for easy operation.
The air inlet provides air through the base of
the stove, via the control slider located under
the base of the door.
The air passes from the base of the stove,
through a sealed airway, around the back
and top of the fire box providing a very hot air
flow over the fire bed.
Secondary air also enters the fire box through
a pre-set bleed at the rear of the stove, and is
heated and distributed through the throat
plate arrangement.
The air control is fully adjustable but has two
main settings in normal use.
10
Multi Purpose Operating Tool
Your stove is supplied with a multi purpose
operating tool, used for adjusting the air inlet
controls and the removal of the ash pan
Emptying the Ash pan
Your stove is supplied with a unique ash pan. To
empty or remove the ash pan, open the fire
door(s), fit the fork end of the operating tool
into the ash pan slots and remove from the ash
pit chamber.
Empty the ash into a suitable container and
replace the ash pan into the stove, withdraw
the operating tool and close the fire door.
DEFRA Stove Installation and User Guide
USER GUIDE

Wood burning air control position
Fully Closed
Fully Open
11
DEFRA Stove Installation and User Guide
USER GUIDE
Solid fuel burning air control position
Fully Closed
Fully Open
Images of a Generic Stove

BK575
Final Factory Check list
Quality / Finish
Flue Outlet
Hot Plate
Fuel Retainer
Firebox Liners
Throat Plate
Door Catch / Door Handle
Operating Tool
User & Installation Guides
Stove Glove
Grate / Fuel Bed
Assembled By………………………....
Checked by……………………………….
ECB5SCF
SIGN5SCF
Model:
The Fireworks - Weycroft Avenue - Axminster - Devon - EX13 5HU
www.arada.uk.com - www.aradastovesandspares.com
Height
Width Depth
Code
kW
Output Height Width Depth
Flue
Diameter
Net
Eciency Rear Side
Height to
centre of
rear ue
Depth
from back
to centre
of top ue
AARROW 5SC B 1 - 4.5 526 391 410 5” 80.3% 400 350 462mm 98mm
ECB5SCF 1 - 4.5 526 391 410 5” 80.3% 400 350 462mm 98mm
SIGN5SCF 1 - 4.5 526 391 410 5” 80.3% 400 350 462mm 98mm
SOL5SC-S2 1 - 4.5 526 391 410 5” 80.3% 400 350 462mm 98mm
mm
Technical Information
Aarrow 5SC B
SOL5SC-S2
Minimum Distance to
Combusbles