arcelik ARK 293 User manual

desk fan
user manual
ARK 293
ARK 294

This product has been produced in environmentally friendly, modern facilities
Please read this manual first!
Dear Customer,
We hope that your product which has been manufactured in mod-
ern facilities and passed through a strict quality control procedure
will give you the best results.
Therefore, we advise you to read through this manual carefully
before using your product and keep it for future reference.
This operation manual will...
...help you use your machine in a fast and safe way.
• Please read the Operation Manual before installing and starting
your machine.
• Particularly follow the instructions related to safety.
• Keep this Operating Manual within easy reach. You may need it
in the future.
• Please read all additional documents supplied with this machine.
Please note that this Operating Manual may be applicable for sev-
eral other models. Differences between models will be identified in
the manual.

1
Contents
1 Safety Warnings 2
3 Using Your Machine 6-7
4 Maintenance And Cleaning 7
2 Technical Aspects Of Your Machine 3-6

2
1Safety Warnings
• Do not ever plug the fan without
finishing the assembly.
• Before plugging the fan, make
sure that the source power is the
same as the declared voltage on
the model sticker.
• Make sure that speed setting
switch is in position “0” before
plugging your fan.
• Always place your fan on stable
surfaces, keep away form watery
places like bath tub, swimming
pool and shower.
• Keep away from children.
• Do not ever use your fan with
wet hands.
• Before moving your fan be sure
that the speed setting switch is in
position “0” and it is unplugged.

3
2Technical Aspects Of Your Machine
1Front guard
Blade fixing nut
Blade
Guard fixing nut
Guard lock
Rear guard
Motor shaft
Pin
Motor
Oscillating knob
Butterfly screw
Neck
Body
Supply cord
Base
Base rubbers
Speed setting
Base fixing nut
2
3
4
5
6
7
8
9
1 0
1 1
1 2
1 3
1 4
1 5
1 6
1 7
1 8
ARK 293
Power : 45 W
Voltage : 230 V ~
Frequency : 50 Hz.
Isolation class : II
Water penetration class : Ordinary
ARK 294
Power : 55 W
Voltage : 230 V ~
Frequency : 50 Hz.
Isolation class : II
Water penetration class : Ordinary
Values stated on your product labels or in
the documentation accompanying it are
obtained in laboratory in accordance with
the relevant standards. These values may
change depending on operational and
environmental conditions of the product.
14

4
Fan Assembly and Preparation
to Use
Assembly of the Base
1- Unscrew the base fixing nut
from the body (part no:18).
2- Hold the base (part no: 15)
with base rubbers facing down
and insert the supply cord from
the hole. Then insert the body to
hole, (you should align the body
goes into the groove to the base,
correct position)
ATTENTION: Do not make as-
sembly if your fan is broken or
damaged.
3- Hold the fan up side down from
the body and insert the supply
cord through the fixing nut with the
instructions facing up and screw it.
4- After screwing the nut place
the supply cord through the canal
located on the edge of the base and
lock it by banding the base. Now
your fan is more stable and the cord
will not border you.
Rear Guard Assembly
1- Take out the blade fixing nut from
the pivot by turning clockwise.
2- Take out rear guard joint nut by
turning counter clockwise.

5
3- Place the rear guard by locating
the 3 bars on the motor to the 3
holes on the guard.
4- Put the joint nut into place and fix
by turning clockwise.
Blade Assembly
ARK 293 : Place the blade by align-
ing with the groove on the blade with
motor pim.
ARK 294 : Place the blade by align-
ing with the hole and motor shaft.

6
The operation should be done prop-
erly. Otherwise the blade will turn in
space and damage the product.
Fix the blade fixing nut bu turning
counter clockwise according to the
direction given on the nut.
Speed Setting
You may run the fan by moving the
rotary switch left / right and choosing
a speed position.
To turn off set the switch in position
“0”.
Oscillation
If you want your fan to spin left and
right within a definite angle and blow
out air press the oscillation knob.
To stop the process pull the knob for
the previous position.
3Using Your Machine

7
Maintenance And Cleaning
4
Adjusting The Blow Out Angle
Before adjusting the blow out angle
turn off your fan. Then you may
adjust the blowing angle by moving
the guard upwards and downwards
as show on the picture.
1- Make sure that the fan is turned
off and unplugged before starting
any cleaning process.
2- Do not use substances which
may damage the product Rinse with
a damp piece of cloth and do not
use before the fan gets dry.
3- Do not immerse into water or any
other liquid.
4- Contact with the authorized tech-
nical service if the supply cord needs
repair or change.
WARNING! When cleaning the
guard and blade they should be dis-
assembled. After cleaning the blade
and guard should be assembled
again.