Archgard Euro 65 Owner's manual

Euro 65
Direct Vent
Gas Fireplace
7116 Beatty Dr
Mission, BC V2V 6B4
Canada
For use with natural gas or
propane
Installer: Please leave this manual with the appliance owner for future reference
USERS
INSTALLATION
OPERATION &
MAINTENANCE
MANUAL
WARNING: If the information in this manual is
not followed exactly, fire or explosion may result
causing property damage, personal injury or loss of
life.
— Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
—WHAT TO DO IF YOU SMELL GAS
· Do not try to light any appliance.
· Do not touch any electrical switch; do not use
any phone in your building.
· Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
· If you cannot reach your gas supplier, call the
fire department.
— Installation and service must be performed by a
qualified installer, service agency or the gas
supplier.
200-0050
30 DEC 02
U
C Master Contract: 214018
This appliance may be installed in an af-
termarket permanently located, manufac-
tured home (USA only) or mobile home,
where not prohibited by local codes.
This appliance is only for use with the type
of gas indicated on the rating plate. This
appliance is not convertible for use with
other gases, unless a certified kit is used.
fire-parts.com

CONTENTS
Introduction 3
General Information 4
Appliance Description 5
Dimensions and Clearances 6
Installation Instructions 7—18
Operation Instructions 19—20
Maintenance 21
Trouble Shooting Instructions 22—23
Wiring Diagrams 24
Servicing 25—27
Replacement Parts 28
Warranty 29
Warranty Registration Mail In Form 30
Patents Pending
CAUTION
Due to high temperatures, the appliance should be located out of traffic and away from
furniture and draperies.
Children and adults should be alerted to the hazards of high surface temperature and
stay away to avoid burns or clothing ignition.
Young children should be carefully supervised when they are in the same room as the
appliance.
Clothing or other flammable material should not be placed on or near the appliance.
Do not operate this appliance with the glass front removed, cracked or broken. Be
careful not to strike or slam the glass. Replacement of the glass should be done by a
licensed or qualified service person.
Installation and repair must be done by a qualified service person. Any parts removed
or opened for servicing of the appliance must be properly replaced prior to operating
the appliance.
The appliance must be inspected before use and at least annually by a qualified
service person. More frequent cleaning maybe required due to excessive lint from
carpeting, bedding material, etc. It is imperative that the control compartments, burners
and circulating air passageways for the appliance be kept clean.
fire-parts.com

Euro 65 3
INTRODUCTION
Congratulations for choosing an Archgard fireplace.
The Euro 65 is one of the most advanced direct vent fireplace heaters available. It is
solidly designed using the latest technology and manufactured to the highest quality. It
is our aim to provide you an appliance with many trouble free years of reliable service.
Some of the many features are:
• Heater Classification The Euro 65 is classified as a heating appliance.
Therefore, it has additional safety devices built-in and it
can be operated continuously for zone heating.
• High Efficiency The Euro 65 has one of the highest efficiencies of any
gas fireplace; which means that it is less expensive to
operate.
• Adjustable Flame The flame aesthetics and heat output can be adjusted to
suit the owner’s liking and heating needs.
• Solid Construction The Euro 65 is constructed mainly of 14 and 18 gauge
galvanized and aluminized steel for long life and durability.
• Optional Thermostatic The gas control system is “thermostat” ready for any
Control millivolt wall thermostat or wireless remote control
Please read the manual carefully prior to installation and operation of the
appliance. Proper installation, operation and maintenance of the appliance will
provide you with many years of enjoyment. We recommend you record the
following information:
Fireplace Model Number __________________________________
Fireplace Serial Number __________________________________
Date of Installation _______________________________________
Type of Gas Used by the Fireplace __________________________
Dealer’s Name __________________________________________
__________________________________________
fire-parts.com

Euro 65 4
GENERAL INFORMATION
SPECIFICATIONS
This appliance is tested and certified to the following US and Canadian gas appliance
standards.
- ANSI Z21.88a-1998/CSA 2.33a-M98, Vented Gas Fireplace Heaters,
- ANSI Z21.44-1995, CAN1-2.19-M81, Direct Vent Wall Furnaces
- CAN/CGA-2.17-M91, Gas-Fired Appliances for Use at High Altitudes
Please contact Archgard Industries Ltd., if you have any questions regarding the certification of
this appliance.
APPLIANCE CERTIFICATION
INSTALLATION CODES
This appliance must be installed by a qualified gas appliance installer.
The installation must conform with the local codes or, in the absence of local codes, with the
current National Fuel Gas Code, ANSI Z223.1/ NFPA 54, in the US or Installation Code, CAN/
CGA-B149, in Canada. Electrical connections and grounding must conform with local code, or
current National Electrical code, ANSI/NFPA No. 70-1987, in the US and in Canada, the
current Canadian Electrical Code, CSA C22.1.
HIGH ALTITUDE INSTALLATION
When installing this appliance beyond 4500 ft. (1372 m) above sea level. The appliance must
be properly de-rated and installed according to local codes, in the absence of local codes, with
the current National Fuel Gas Code, ANSI Z223.1/ NFPA 54, in the US or Installation Code,
CAN/CGA-B149, in Canada.
Natural Gas (NG) Propane (LP)
Manifold Pressure 1.6-3.5 in. W.C. (0.4 -0.9 kPa) 3.6-10.0 in. W.C. (0.9-2.5kPa)
Min. Supply Pressure for
Purpose of Input Adjustment 4.5 in. w.c. (1.2 kPa) 11.0 in. w.c. (2.8 kPa)
Orifice Size #37 DMS (2.66mm dia.) #51 DMS (1.5mm dia.)
Nominal Input Rating 30,000 - 20,100 BTU/hr
( 8.8 - 5.9 kW) 30,000 - 18,000 BTU/hr (8.8 - 5.3 kW)
Output (Fan On) @ Max. Rating 22,500 BTU/hr (6.9 kW) 23,100 BTU/hr (6.9 kW)
Output (Fan Off) @ Max.
Rating 23,560 BTU/hr (6.9 kW) 23,560 BTU/hr (6.9 kW)
Altitude 0-4500 ft (0 - 1372 m) 0 - 4500 ft (0 - 1372 m)
Primary Air Opening 1/8 in. (3.2 mm) 3/8 in. (9.6 mm)
fire-parts.com

Euro 65 5
APPLIANCE DESCRIPTION
FLAT FRONT VERSION
Top Louvers
Ceramic Viewing
Glass
Bottom Louvers
(remove to access
controls)
BAY FRONT ADDED
Gold or black
louver kit
Optional gold trim
Control access door
fire-parts.com

Euro 65 6
DIMENSIONS AND CLEARANCES
APPLIANCE DIMENSIONS
BACK 0” to stand-offs
SIDES 0” to stand-offs
TOP 0” to stand-offs
BOTTOM 0”
ADJACENT SIDE WALL 1” to side of faceplate
MANTLE see diagram
VENT 1” to outside side and bottom surface,
2” to outside top surface.
CLEARANCES TO COMBUSTIBLES:
37 3/4”
21 1/2”
39 1/2”
TOP VIEW SIDE VIEW
FRONT VIEW
3”
6”
Combustible mantle allowed in
shaded area. Mantle extension
may be increased 1” (25mm) for
each additional 1” (25mm)
increase in clearance height.
6” (152 mm)
Minimum Height From Top
Surround:
Minimum Height From Bottom of
Appliance:
MANTEL CLEARANCE NOTE: Low profile wooden crowns and
moldings above the unit are not
considered as mantles. I.E. 1” or less
protrusions on the upper mantle facing
are acceptable
Mantel may start
39” and above.
39”
14” (356mm)
45” (1143 mm)
fire-parts.com

Euro 65 7
INSTALLATION INSTRUCTIONS
PRECAUTIONS
• This appliance must be installed by a qualified gas installer and the
installation must conform to the installation codes.
• Provide adequate clearance around air openings of the appliance. Never
obstruct front openings.
• Provide adequate clearances for proper operation and servicing of the
appliance.
• This appliance must be properly connected to a venting system.
• This gas appliance must not be connected to a chimney serving a separate
solid-fuel burning appliance.
• Do not use this appliance if any part has been under water. Immediately call a
qualified service technician to inspect the appliance and to replace any part
of the control system and any gas control which has been under water.
• Caution: Label all wires prior to disconnection when servicing controls.
Wiring errors can cause improper and dangerous operation.
• Verify proper operation after servicing.
• Do not use substitute materials.
• Do not abuse glass doors by striking or slamming shut.
• Do not use abrasive cleaners.
• Use only approved fireplace glass cleaner for cleaning your glass.
LOCATING GAS FIREPLACE
This appliance must be installed in any location that is free of plumbing, electrical wiring and
heating or air conditioning ducts. Select a location that is accessible for venting. See
ALLOWABLE TERMINATION LOCATIONS.
GAS CONNECTIONS
Have your gas supplier or a qualified gas fitter run a gas supply line into the fireplace. The line
must be properly sized and fitted according to the installation codes. Immediately up stream of the
supply connection, the fitter shall provide an accessible manual shut-off valve and a 1/8 NPT
plugged tapping accessible for connection to a test gauge.
CAUTION: The appliance and its individual shutoff valve must be disconnected from the gas
supply piping system during any pressure testing of that system at test pressures in excess of 1/2
psig (3.5 kPa). The appliance must be isolated from the gas supply piping system by closing its
individual manual shutoff valve during any pressure testing of the gas supply piping system at test
pressures equal to or less than 1/2 psig (3.5 kPa). Failure to do so will damage the appliance’s gas
valve. Such damage is not covered by the manufacturer’s warranty.
fire-parts.com

Euro 65 8
INSTALLATION INSTRUCTIONS
Natural Gas Pressure Settings:
The inlet supply or line pressure must be a minimum of 4.5” wc (1.1 kPa) and a maximum of 8”
wc (2 kPa). The orifice has a #37 hole.
ELEVATION INPUT RATING
0-4500 ft. (0-1400 m) 30,000 BTU/hr (8,800 watts)
4500 ft. (1400 m) + 30,000 BTU/hr (8,800 watts) less 4% per 1000 ft. (300 m)
or reduce manifold pressure by 0.25” wc (0.06 kPa) per 1000 ft. (300m)
Propane Pressure Settings:
The inlet supply or line pressure must be a minimum of 11” wc (2.8 kPa) and a maximum of
14” wc (3.5 kPa). The orifice has a #53 hole.
ELEVATION INPUT RATING
0-4500 ft. (0-1400 m) 30,000 BTU/hr (8,800 watts)
4500 ft. (1400 m) + 30,000 BTU/hr (8,800 watts) less 4% per 1000 ft. (300m)
or reduce manifold pressure by 1” wc (0.25 kPa) per 1000 ft. (300m)
NOTE: THE INPUT RATING SHOULD ALWAYS BE CHECKED WHEN FIRST RUNNING
THIS APPLIANCE. To do this, reduce the background flow rate, time the meter, light the
fireplace and take another reading. Check with your gas supplier for the gas BTU content at
your elevation. Input is the rate of flow multiplied by the heating value of the gas (cubic feet/
hour x BTU per cubic feet). Adjust the manifold pressure so that the unit does not operate
above the rated input. To do this, loosen the screw on the variable input knob on the valve and
reposition that the maximum input is correct. Retighten the screw.
ELECTRICAL CONNECTIONS
The Euro 65 comes complete with Blower installed and wired to an internal junction box.
Have a qualified electrician run a 120VAC supply line to the lower left side of the fireplace
before installing the appliance. He should leave 18” (460mm) of the supply line free for ease of
connection to the appliance. Connect the electrical supply line to the appliance at the same
time the gas line is being connected to the appliance.
Flip open the bottom grill and undo the 2 screws holding the control panel. Run the line into the
left side of the appliance through the hole in the rear of the junction box and hold with a
standard 7/8” clamp. Connect the ‘live’ (black) supply conductor to the free black conductor
from the speed controller with a marrette type wire connector. Connect the ‘neutral’ white
supply conductor to the free white conductor from the convection fan with a marrette type wire
connector. Connect the ‘ground’ (green or bare) conductor to the ground screw in the junction
box. Replace the junction box cover and control panel and fasten with the 2 screws.
fire-parts.com

Euro 65 9
INSTALLATION INSTRUCTIONS Cont...
MO
SPEED
CONTROL
110F (43ºC) N.O.
THERMAL SNAP
SWITCH
CONVECTION BLOWER
LINE
GROUND
NEUTRAL
SIDE OF GAS
FIREPLACE
120 VAC white
black
SPEED CONTROL
LINE
GROUND
NEUTRAL
110F (43ºC) N.O.
THERMAL SNAP
SWITCH
CONVECTION BLOWER
VENT TERMINATION
1.See ALLOWABLE TERMINATION LOCATIONS and establish a suitable vent termination
location.
2.In heavy snowfall areas make sure vent termination is located where it can not be block by
snow or snow from snow removal equipment.
3.Locate vent termination away from plants, bushes or any other object near the vent
termination that will interfere or obstruct the air flow around it.
4.DO NOT recess vent termination into walls, sidings or planters.
5.Vent terminations located below 7ft from grade level or anywhere that it can be a burn hazard
to the public, such as patios and balconies, must be protected with an Archgard approved
termination cage.
WIRING DIAGRAM
ALLOWABLE TERMINATIONS LOCATIONS.
See venting chart for
maximum and minimum
vertical/horizontal
venting configurations.
fire-parts.com

Euro 65 10
INSTALLATION INSTRUCTIONS
FRAMING DIMENSIONS
37 3/4”
16-1/4”
39 1/8”
27 5/8”
37 3/4”
55 1/4”
37 3/4”
*38” 16-1/4”
* This dimension allows the top of the fireplace to slide under. If more rigidity is
required. A stud may be added to the back of the top nailing flange after the
fireplace is installed.
TERMINATION
FRAMING
11”
10”
NOTE: Be sure to include 1/4” rise per
foot of horizontal length.
For rear vented fireplace be
sure to include 1” vertical rise
minimum per foot of horizontal
lenght beyond 6”.
fire-parts.com

Euro 65 11
V
E
R
T
I
C
A
L
H
E
I
G
H
T
INSTALLATION INSTRUCTIONS Cont...
VENTING
The appliance will not function without being connected to a proper venting system.
This appliance may only use direct vent system supplied by Archgard, or Simpson Dura-
Vent direct vent systems with Archgard SDK-3 adapter.
• Chart is for one 90° bend, with 1/4” (7 mm)vertical raise minimum per foot of horizontal
length.
• For each additional 90° or two 45°, add one foot of vertical height.
• Maximum three 90º bends, or equivalent.
• Minimum 2 ft (610 mm) straight length between bends.
VENTING ABOVE ROOF OF THE HOUSE USING A VERTICAL TERMINATION
Use Simpson Dura-Vent listed direct vent system caps for all vertical vent termination
applications (through the roof).
Please follow the venting instructions as strictly as possible to
obtain the best performance from the appliance.
See next page for
restrictor placement
fire-parts.com

Euro 65 12
ALLOWABLE TERMINATION LOCATIONS
Canadian Installations (1) US Installations (2) Canadian Installations (1) US Installations (2) A= Clearance above grade, ve- randa, porch, deck, or balcony
12 inches (30 cm) 12 inches (30 cm) J= Clearance to nonmechaniacl air
supply inlet to building or the combustion air inlet o any other appliance
12 inches (30 cm) 9 inches (23 cm)
B= Clearance to window or door that may be opened 12 inches (30 cm) 12 inches (30 cm) K= Clearance to a mechanical
air supply inlet 6 feet (1.83 m) 3 feet (91 cm) above if
within 10 feet (3 m) hori-
zontally
C= Clearance to permanently closed window * * L= Clearance above paved
sidewalk or paved driveway located on public property
7 feet (2.13 m) + *
D= Vertical clearance to ventilated soffit located above the terminal within a horizontal distance of 2 feet (61 cm) from the center line of the terminal
* * M= Clearance under veranda,
porch, deck, or balcony 12 inches (30 cm) ++ *
E= Clearance to unventilated soffit * * F= Clearance to outside corner * * G= Clearance to inside corner * * H= Clearance to each side of center line extended above meter/regulator assembly
3 feet (91 cm) within a
height 15 feet (4.5 m)
above the
meter/regulator assembly
*
L= Clearance to service regulator vent outlet 3 feet (91 cm) *
(1) In accordance with the current CSA B149.1, National Gas and Propane Installation Code (2) In accordance with the current ANSI Z223.1/NFPA 54, National Fuel Gas Code (+) A vent shall not terminate directly above a side walk or paved driveway that is located between two single family dwellings and serves both dwellings (++) Permitted only if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the floor. (*) For clearances not specified in ANSI Z223.1/NFPA 54 or CSA B149.1, “Clearances shall be in accordance with local installation codes and the requirements of the gas supplier.”
fire-parts.com

Euro 65 13
INSTALLATION INSTRUCTIONS Cont...
Restrictor Placement
Restictor Number 1
Restictor Number 2
Simpson Duravent Archgard System
Archgard System
In the Archgard system the restrictors are placed on the exhaust outlet on the appliance.
Simpson Duravent
With Simpson Duravent the restrictors can be placed anywhere in the system. Locate the
restrictor in the exhaust section fitting into the formed lip.
Restrictor Placement
fire-parts.com

Euro 65 14
INSTALLATION INSTRUCTIONS Cont...
For best venting performance, here are some general venting rules that we recommend:
1.Use only Archgard or Simpson Dura Vent direct vent systems and components.
2.Maintain a minimum of 1” (26 mm) clearance to combustibles from the outside surfaces of
vertical vents and minimum of 1” (26 mm) sides and bottom, and 2” (51 mm) from top surfaces
of horizontal vents.
3.Observe any local code restrictions, if any, regarding the installation of this type of gas
appliance.
4.Observe the venting chart given in this manual.
5.Use vent spacers between the inside and outside vents at every 3 ft (915 mm) intervals
(Archgard vent kits only).
6.Never slope horizontal vents downwards.
7.Maintain at least a rise of 1/4” (7 mm) for every 1 ft (305 mm) of horizontal vent.
8.Terminate the vent with a suitable vent termination supplied by Archgard Part # TK-1 or
Simpson Dura Vent.
9.Support horizontal vents every 3 ft (915 mm) to prevent it from sagging.
VENTING Cont...
VENTING CONNECTION
The intake pipe shall be securely fastened to the appliance and to the terminal and all joints
shall be secured using a minimum of 3 screws evenly spaced around the pipe.
Approximately 1” from the end of the 4” pipe outlet at the appliance and at the 4” terminal inlet
apply a bead of Mil Pac 1/4” wide. Slide the 4” pipe onto the appliance and secure with 3 screws
evenly spaced to the outlet. Repeat the procedure at the terminal inlet.
Install a vent spacer between the outer and the inner liner to maintain clearances. Spacers shall
be installed at every change of direction. (See diagram)
Clearance to combustible material and fire-stops shall be install as required by the installation
codes.
APPROVED VENT COMPONENTS
PART # DESCRIPTION
TVK-1 Flex Vent Kit with 36” vent length (includes TK1)
TVK-2 Flex Vent Kit with 60” vent length (includes TK1)
TK-1 Horizontal termination head only
VSD-1 Vinyl siding deflector
SNK-24 24” Snorkel
SDA-1 Adaptor, Flex to Simpson Dura-Vent
SDA-3 Adaptor, Appliance to Simpson Dura-Vent
DV-GS Simpson Dura-Vent venting system
fire-parts.com

Euro 65 15
Termination
Fire-stop
Sleeve
7” and 4” flex
vent lengths
(compressed
Cement
Screws
Spring
spacers
4” exhaust vent
with spring spacers
Vent system
assembled
Cut sleeve to fit wall thickness
VENT ASSEMBLY
VENT KIT COMPONENTS (TVK-1)
INSTALLATION INSTRUCTIONS Cont...
fire-parts.com

Euro 65 16
GLASS DOOR
INSTALLATION INSTRUCTIONS Cont...
WARNING: Do not attempt to remove the glass door when the appliance is hot.
Removing the Glass Door
Remove the top louver and open bottom louver
There are 2 buckle latches under the door frame. Lift the lever on the back of the
latches to release them. Unhook the latches from the bottom of the door. Swing the
bottom of the door towards you. Lift up on the whole door to unhook the top of door.
Carefully remove the door put it away at a safe location where it cannot be scratched
or damaged.
Replacing the Glass Door
The reverse procedure of Removing the Glass Door.
buckle latch
buckle latch
top of door
hooks onto
fireplace
fire-parts.com

Euro 65 17
WARNING: Do not place logs in any other configuration than that
shown. Under no circumstances are logs to be modified.
INSTALLATION INSTRUCTIONS Cont...
PLACEMENT OF LOGSET, COALS & EMBER WOOL
• Place the back log on the back log support at the back of the fireplace.
• Place the front log on top of the burner as shown. There are pins on the burner to
locate the log.
• Place the cross log directly on the burner and the back logs as shown. There are
locating pins on the burner to position the front of the cross log. The back end of the
cross log is cradle in a recess on the back log.
• Place coals in the trough along the front of the burner.
• Tear ember wool into 1/2” to 3/4” diameter ember pieces and place them on the front
ledge of the burner and around the outer edges of the burner ports. Keep the embers
from obstructing the burner ports.
WARNING : Do not place the embers directly on the burner ports, fire, explosion or
excessive carbon monoxide (CO) may result, causing property damage,
personal injury or loss of life.
BURNER
BACK LOG
COALS
EMBERS
BURNER TRAY
CROSS LOG
FRONT LOG
fire-parts.com

Euro 65 18
NOTE: Ensure that the fireplace is turned off and cool.
Move the bay assembly over the front of the appliance, center in front of the flat
door and hang over existing door.
You have the option to install the bay door with standard flat louvers or bay louvers.
Choose one of the following:
• Black flat louver kit BFLK-65/70
• Gold tone flat louver kit GFLK-65/70
• Mixed gold/black flat louver kit MFLK-65/70
• Black flat louver kit hinged BFLKH-65/70
• Gold flat louver kit hinged GFLKH-65/70
• Mixed gold/black flat louver kit hinged MFLKH-65/70
• Mixed pewter/black louver kit hinged MPLKH-65/70
• Black bay louver kit BBAYLK-65
• Gold plated bay louver kit GBAYLK-65
The unhinged louvers have hooks at each end for mounting.
The hinged louvers have hooks on the upper and hinges on the lower assemblies.
If you install the bay louvers you will receive control knob extensions for easy ac-
cess.
INSTALLATION INSTRUCTIONS Cont...
OPTIONAL BAY DOOR INSTALLATION
TOP BAY LOUVERS
BAY DOOR
BOTTTOM SHELF/ CONTROL ACCESS
WARNING: THE OPTIONAL BAY DOOR IS A DECORATIVE OPTION ONLY AND IS
MANUFACTURED WITH TEMPERED GLASS. THIS UNIT MUST NOT BE OPERATED
WITHOUT THE FLAT CERAMIC GLASS DOOR SECURED IN PLACE, BEHIND IT.
fire-parts.com

Euro 65 19
OPERATION INSTRUCTIONS
FOR YOUR SAFETY, READ BEFORE LIGHTING
INITIAL OPERATION
• Check that the appliance is properly vented and connected to the gas supply.
• Check that the logs and branches are properly placed.
• Check that all external parts, such as grills, door and faceplate are properly attached
and fastened.
• Check that there are no finger prints left on gold surfaces as high temperature can
bake these prints permanently.
NOTE : When operated for the first few times, the appliance will emit some odor and
fumes. This is due to the heat from the appliance evaporating the oils and solvents
used in fabricating the appliance. Close off the room to the rest of the house and
open all windows. Keep the room well ventilated as smoke alarm may sound. Run
the appliance for at least 4 hours at maximum setting with blower set to “OFF” to
allow paint to cure.
WARNING : If you do not follow these instructions exactly, a fire or explosion
may result, causing property damage, personal injury or loss of
life. Do not operate the appliance with the glass front removed,
cracked or broken. Replacement of the glass should be done by a
licensed or qualified service person.
fire-parts.com

Euro 65 20
OPERATION INSTRUCTIONS Cont..
LIGHTING INSTRUCTIONS (copy of instruction plate found in control panel)
1. Set the thermostat to the lowest setting and turn the remote
switch to “OFF”.
2. Turn off all electric power to the appliance if service is to be
performed.
3. Open lower louvers or access door.
4. Press slightly and turn control knob clockwise 3to “OFF”.
Do not force.
5. Close lower louvers or access door.
Flame Adjustment Knob
Sparker
Control Knob
Automatic Valve
Sparker
Control
Manual Valve Pilot
A. This appliance has a pilot which must be lighted by a spark
ignitor. When lighting the pilot follow these instructions
exactly.
B. BEFORE LIGHTING smell all around the appliance area
for gas. Be sure to smell next to the floor because some
gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in
your building.
• Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire
department.
C. Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by hand
don’t try to repair it, call a qualified service technician.
Forced or attempted repair may result in a fire or
explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system
and any gas control which has been under water.
FOR YOUR SAFETY READ BEFORE
WARNING: If you do not follow these instructions exactly, a fire of explosion may result causing
property damage, personal injury or loss of life.
1. STOP! Read the safety information above on this label.
2. Set the remote switch to “OFF”. Set the thermostat to the
lowest setting. (Only if your appliance is equipped with
these devices.)
3. Turn off all electric power to the appliance.
4. Open lower louvers or access door.
3. Press slightly and turn the control knob clockwise 3to the
“OFF” position.
4. Wait 5 minutes to clear out any gas. Then smell for gas,
including near the floor. If you smell gas, STOP! and follow
instruction “B” above.
5. Find pilot. It is located between the logs near the center
behind the burner.
6. Press slightly and turn control knob counterclockwise 4to
“PILOT”. Depress knob and light pilot by repeatedly
pressing the sparker. Once flame is established, hold knob
depressed for approximately 30 seconds. Release knob. If
pilot should go out, repeat steps 3 to 5.
• If the knob does not pop up when released, stop and
immediately call your service technician or gas supplier.
• If the pilot will not stay lit after serveral tries, turn the gas
control knob to “OFF” and call your service technician or
gas supplier.
7. If the appliance has a manual valve, turn gas control knob
counterclockwise 4to the desired heat setting from “LO”
to “HI”. If the appliance has an automatic valve, turn gas
control knob counterclockwise 4to “ON” and set the flame
adjustment knob to the desired heat setting from “LO” to
“HI”.
8. Set the remote switch to “ON”. Set the thermostat to the
desired setting. (Only if your appliance is equipped with
these devices.)
9. Turn on all electric power to the appliance.
10. Close louver or access door.
LIGHTING INSTRUCTIONS
TO TURN OFF GAS TO APPLIANCE
303-0001 28MAY01
fire-parts.com