Arec DS-4CU User manual

Speaker Tracking System
DS-4CU
2021/6/23 Updated(DS-4CU v6.0.0.41)

Description
DS-4CU is a device that helps to communicate between the microphone system and PTZ
camera to provide a close-up view of the active speaker in a meeting/conference room.
It synchronizes the microphone system’s status(active microphones’ ID) and controls the
camera to move to the corresponded speaker by the preset position with the preferred layout,
overlay, and background.
When paired with an AREC media station, It could also control the station’s theme when a
microphone is activated/deactivated.
AREC Inc.© All Rights Reserved 2021 www.arec.com
All information contained in this document is Proprietary
2

Installation
Connection
AREC Inc.© All Rights Reserved 2021 www.arec.com
All information contained in this document is Proprietary
3

Configuration
Video Inputs - Camera Setup
DS-4CU supports cameras with different video output interfaces (HDMI /VGA /Network
cameras(ONVIF protocol) / IP streams: RTSP(Network Cameras) /RTMP /RTP).
The following guide gives an example of the commonly used ONVIF protocol of network
cameras.
Register Camera
1. Make sure the cameras are correctly connected. And go to DS-4CU web Admin page →
Media I/O → Network device manage → Network cameras
2. Click
3. Click , insert the username and password, and click to register
the camera
AREC Inc.© All Rights Reserved 2021 www.arec.com
All information contained in this document is Proprietary
4

4. Repeat the last step if more cameras are needed
*Note: If your camera doesn’t support Onvif protocol, it cannot be found by camera search on
DS4CU. Please go to the Video input page and select "Signal type" to "Encoder" in the "Video
Inputs" and fill in the stream URL of your camera.
**Note: DS-4CU supports IP stream profile: H264, 1920x1080, 30 FPS, Bitrate 4Mbps.
AREC Inc.© All Rights Reserved 2021 www.arec.com
All information contained in this document is Proprietary
5

Assign cameras to video inputs
DS-4CU could be connected to up to 4 video input sources; they could be either HDMI/VGA/IP
camera/encoder(stream sources: RTP/RTSP/RTMP).
*Note: HDMI/VGA only available in 1st and 2nd Video input
1. Go to web admin → Media I/O → Video inputs.
AREC Inc.© All Rights Reserved 2021 www.arec.com
All information contained in this document is Proprietary
6

2. In the preferred video input section,
(1) select "Network Camera" in Signal type,
(2) select the IP address of the camera,
(3) select "over IP (ONVIF)" for PTZ control,
(4) and click Apply
Repeat the steps above to add all necessary cameras.
AREC Inc.© All Rights Reserved 2021 www.arec.com
All information contained in this document is Proprietary
7

Connect to the microphone system
1. Retrieve the Shure’s Microphone’s IP. For different Shure series:
○ MXA Series:
The IP of MXA910 /MXA710 /MXA310
○ MXCW Series:
The IP of the APT(Access Point Transceiver), which is MXCWAPT
○ MXW Series:
The IP of the APT(Access Point Transceiver), which is either an MXWAPT8,
MXWAPT4, or MXWAPT2.
2. Go to DS-4CU’s web Admin page → Speaker Tracking → Control settings
3. Find the External system section and select the corresponding microphone.
Insert the microphone system’s IP and click Apply.
AREC Inc.© All Rights Reserved 2021 www.arec.com
All information contained in this document is Proprietary
8

4. Go to the display’s graphic user interface and click the Info button in the bottom-right
corner.
5. To ensure the connection between DS-4CU and the microphone was successfully set,
activate any microphone to see if any string was shown like the image below.
AREC Inc.© All Rights Reserved 2021 www.arec.com
All information contained in this document is Proprietary
9

Control settings - General default
This configuration defines how the image should be displayed when there is no microphone
activated.
1. Go to DS-4CU’s web Admin page → Speaker Tracking → Control settings, and find the
General default
2. Click the edit button to edit the theme of general default(no microphone activated).
And click [Apply].
Parameter
Description
Range
Content Preset
Preset Position of the camera that
set as 1st video input source
-1 ~ 255, -1 = OFF
Cam1 Preset
Preset Position of the camera that
set as 2nd video input source
-1 ~ 255, -1 = OFF
Cam2 Preset
Preset Position of the camera that
set as 3rd video input source
-1 ~ 255, -1 = OFF
Cam3 Preset
Preset Position of the camera that
set as 4th video input source
-1 ~ 255, -1 = OFF
Overlay
Overlay ID
0 ~ 255, 0 = no overlay
Layout
Layout ID
1 ~ 255
Background
Background ID
0 ~ 255, 0 = no background
Ext. Recorder
Theme
Paired AREC media station Theme
ID
as the drop-down list defines
*Auto: DS-4CU saves the last theme ID of the
media station before any microphone is activated,
and returns to this theme when all mics are OFF.
AREC Inc.© All Rights Reserved 2021 www.arec.com
All information contained in this document is Proprietary
10